The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds node i2c bus 3 to get the appropriate userland device
file. So for prototyping it's possible to experiment within userland.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW54xx can provide PWM4 out either the off-board backlight connector
or the off-board digital I/O connector. By default the pinmux routes it
to the backlight connector but this pinctl alternate provides documentation
for those who may want to change it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since uboot v2016.01-rc2, which supported basic psci for i.mx7d.
So imx7d's second core can be enabled by psci.
Without arch timer, every timer event will be boardcasted to each core.
arch timer has local timer irq for each core.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the remaining SAI instances SAI0, SAI1 and SAI3. All
instances are very similar, except that the DMA channel of SAI3
is available on MUX1 (compared to MUX0 for SAI0-SAI2). Also,
SAI3 has a slightly different memory map due to a deeper FIFO,
however in practice the current driver works for SAI3 fine.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 8ba671efdb.
As reported by kbuild test robot <fengguang.wu@intel.com>:
In file included from arch/arm/boot/dts/mt2701-evb.dts:16:0:
>> arch/arm/boot/dts/mt2701.dtsi:18:28: fatal error: mt2701-pinfunc.h: No such file or directory
#include "mt2701-pinfunc.h"
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the switch from mmp_pdma to pxa_dma driver for pxa architectures,
the pxa_dma requires 2 arguments, namely the requestor line and the
requested priority.
Fix the only left device node which was still passing only one argument,
making the pxa3xx-nand driver misbehave in a device-tree configuration,
ie. failing all data transfers.
Fixes: c943646d1f ("ARM: dts: pxa: add dma engine node to pxa3xx-nand")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Merge "Broadcom devicetree changes for 4.6" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes:
- Rafal adds a Device Tree for the D-Link DIR-885L router which is based on the
BCM47094 SoC similar to the BCM4709
- Simran adds proper audio clock Device Tree nodes to the Cygnus platforms
- Martin adds the auxiliary SPI controllers, makes the UART naming convention
more standard, and finally adds the auxiliary UART found in the BCM2835 to the
BCM2835 Device Tree
- Remi adds PWM clock support to the BCM2835 Device Tree
- Lubomir adds a Device Tree for the Raspberry Pi Model A
- Alexander adds Device Tree information for the Raspberry Pi USB power domain
- Dhananjay enables the GPIO-A controller for the Northstar Plus SoCs
- Jon fixes the PCIE Device Tree nodes by pulling them out of the bus-level node,
removes duplicate CPU definitions, adds PMU nodes, SP804 timers, and SP805 watchdog
to the Northstar Plus SoCs
* tag 'arm-soc/for-4.6/devicetree' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: add bcm2835-aux-uart support to DT
ARM: dts: NSP: Add SP805 Support to DT
ARM: dts: NSP: Add SP804 Support to DT
ARM: dts: NSP: Add PMU Support to DT
ARM: dts: NSP: Fix CPU DT issue
ARM: dts: NSP: Fix PCIE DT issue
ARM: dts: enable GPIO-a for Broadcom NSP
ARM: bcm2835: Add the Raspberry Pi power domain driver to the DT.
ARM: bcm2835: dt: Add Raspberry Pi Model A
ARM: bcm2835: follow dt uart node-naming convention
ARM: bcm2835: Add PWM clock support to the device tree
ARM: bcm2835: add the auxiliary spi1 and spi2 to the device tree
ARM: dts: Add audio clock to the existing Broadcom Cygnus clock DT
ARM: BCM5301X: Add DT for D-Link DIR-885L
With the newly available MSIX driver for Alpine, add the corresponding
node in the Alpine device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Merge "ARM: Xilinx Zynq dt patches for v4.6" from Michal Simek
- Add usb phy for Zybo
- Use earlycon instead of earlyprintk
* tag 'zynq-dt-for-4.6' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Use earlycon instead of earlyprintk
ARM: dts: zynq: Enable USB and USB PHY for ZYBO
Merge "ARM: Keystone DTS for 4.6" from Santosh Shilimkar:
ARM: DTS: Add new bindings for K2G and the K2G evm
K2G SoC family is the newest version of the Keystone family of processors.
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
* tag 'keystone_dts_for_4.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Add minimum support for K2G evm
ARM: dts: keystone: Add Initial DT support for TI K2G SoC family
ARM: keystone: Create new binding for K2G SoC
Device tree changes for omaps for v4.6 merge window. Mostly just
adding board specific devices and few new boards:
- N900 improvments for adp1653 and gpio keys
- Add missing bandgap data for omap3
- Add more devices for compulab cm-t335
- Add n950 WLAN support, enable modem, add pinctrl for SSI
- Correct dm814x and dra62x auxclk rate, add support for GPMC and NAND
- Add syscon node for PHY's on dra7
- Add support more devices on logicpd torpedo
- Add USB host support for igep and specify boot console
- Fix audio clock for am335x-sl50 and specify boot console
- Remove deprecated tx-fifo-resize for dwc3 that was only used on
omap5 es1.0
- Add dra7 thermal data
- Update am43x-epos-evm compatible string to am438
- Add support for logicpd dm3730 som-lv
* tag 'omap-for-v4.6/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (38 commits)
ARM: dts: am57xx-beagle-x15: Add eeprom information
ARM: dts: Add HSUSB2 EHCI Support to Logic PD DM37xx SOM-LV
ARM: dts: n900: Use linux input defines instead hardcoded constants
ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV
ARM: dts: omap3logic: Add PWM-Backlight
ARM: dts: omap3-n900: Allow gpio keys to be disabled
ARM: dts: am43x-epos-evm: Add the am438 compatible string
ARM: dts: DRA7: Add missing IVA and DSPEVE thermal domain data
ARM: dts: DRA7: Add IVA thermal data
ARM: dts: DRA7: Add DSPEVE thermal data
ARM: dts: remove deprecated property dwc3
ARM: dts: OMAP3-N950-N9: Add ssi idle pinctrl state
ARM: dts: am335x-sl50: Fix audio codec setup.
ARM: dts: am335x-sl50: Specify the device to be used for boot console output.
ARM: dts: omap3-igep0030-common: Add USB Host support
ARM: dts: igep00x0: Specify the device to be used for boot console output.
ARM: dts: LogicPD Torpedo: Set HSUSB0 Pin Mux
ARM: dts: OMAP3-N950-N9: Enable modem
ARM: dts: OMAP3-N950-N9: Enable SSI module
ARM: dts: LogicPD Torpedo: Add SPI EEPROM
...
Merge "ARM: mediatek: dts updates for v4.6" from Matthias Brugger:
Add support for mt7623 SoC.
Enable SMP support for mt7623.
Enable SMP support for mt2701
Add pinctrl for mt2701
* tag 'v4.5-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: Add pinctrl/GPIO/EINT node for mt2701
ARM: dts: mt2701: enable basic SMP bringup for mt2701
ARM: dts: mt7623: enable SMP bringup
ARM: dts: mediatek: add MT7623 basic support
Document: DT: Add bindings for mediatek MT7623 SoC Platform
OrangePi Plus board has dwo leds - green ("pwr") and red ("status")
and a switch ("sw4"). This patch describes them in a devicetree.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds correct aliases to spi and i2c buses so that they get
correct matching bus numbers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds i2c6 device node and pinctrls required for IFC6410 on
MIPI-CSI connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing i2c pinctrl sleep states.
Also add 16mA drive strength to the pins so that we can detect wide
range of i2c devices on the other side of level shifters.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds PCIE support to APQ8064, tested with Ethernet on
Compulab QS600 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes i2c lables to be inline with serial labels.
The reason to do this is that it would look odd if we add aliases in the
board file along with serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
LogicPD has two main Torpedo styles, a version with wireless and a version
without wireless. This version has Bluetooth and WiFi, but there really
isn't an easy way to identify them automatically. This simply adds
"Wireless" to the model to distinguish it from the 'base' model that will
come soon.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] dm816x TRM: SPRUGX8C: 9.2.4.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM335x TRM: SPRUH73L: 7.1.3.3.12.2 NAND Device-Ready Pin
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM437x TRM: SPRUHL7D: 9.1.3.3.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wait pin monitoring is not used for nand so it is pointless to
have the gpmc,wait-monitoring-ns property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the corresponding device node for R_PIO on H3 to the dtsi. Support
for the controller was added in earlier commit.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
APB0 is bearly mentioned in H3 User Manual and it is only setup in the
Allwinners kernel dump for CIR. I have verified experimentally that the
gate for R_PIO exists and works, though. There are probably other gates
there but I don't know their order right now and I don't have access to
their peripherals on my board to test them.
After some experiments and reviewing how this is organized on other
sunxi SoCs, I couldn't actually find any way to disable clocks for R_PIO
and they are working properly without doing anything so I assume they
are connected straight to the 24Mhz oscillator for now.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
