sources for msm8974, this isn't actually a reserved region.
Instead it's marked as "unused" for reserved regions. Let's
remove it so we get back a good chunk of memory.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
AHCI provides the register PORTS_IMPL to let the software know which port
is supported. The register must be initialized by the bootloader. However
in some cases u-boot doesn't properly initialize this value (if it is not
compiled with SATA support for example or if the SATA initialization fails).
The DTS entry "ports-implemented" can be used to override the value in
PORTS_IMPL.
Without this patch the SATA will not work in the following two cases:
* if there has been a failure to initialize SATA in u-boot.
* if ahci_platform module has been removed and re-inserted. The reason is
that the content of PORTS_IMPL is lost after the module is removed.
I suspect that it's because the controller is reset by the hwmod.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
[tony@atomide.com: updated comments with what goes wrong]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch rearrange MT2701 DT nodes to keep them in ascending order.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
[mb: fix pio unit address and order]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
TI DA8xx/OMAPL13x/AM17xx/AM18xx SoCs have extra UART registers beyond
the standard 8250 registers, so we need a new compatible string to
indicate this. Also, at least one of these registers uses the full 32
bits, so we need to specify reg-io-width in addition to reg-shift.
"ns16550a" is left in the compatible specification since it does work
as long as the bootloader configures the SoC UART power management
registers.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The range size for axi is 0x2 bytes too small, as the QSPI needs
0x11c408 + 0x004 (which is 0x0011c40c, not 0x0011c40a). No errors have
been observed with this shortcoming, but fixing it for correctness.
Fixes: 329f98c197 ("ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes")
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
FDT harcoded partition table does not match that one in historical
TI's 2.6.37 kernel and non legacy kernels even use different ECC scheme,
yet noone complained, so remove it altogether.
Also, UBI volumes instead of partitions are used since u-boot-2016.09.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to errata i880 description the speed of Ethernet port 1 on AM572x
SoCs rev 1.1 should be limited to 10/100Mbps, because RGMII2 Switching
Characteristics are not compatible with 1000 Mbps operation [1].
The issue is fixed with Rev 2.0 silicon.
Hence, rework Beagle-X15 and Begale-X15-revb1 to use phy-handle instead of
phy_id and apply corresponding limitation to the Ethernet Phy 1.
[1] http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As the bootloader passes the NAND and the SPI flash partition tables
there is no need to keep them in the kernel device tree.
Removed them.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TI DRA72-EVM Rev C has two DP83867 ethernet phys which support IRQ
generation in case of phy/link status changes. The INT/PWDN lines from both
DP83867 phys are wired to DRA7 gpio6.16, so reflect the same in DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix a typo in impedance setting for ethernet-phy@3
Fixes: b76db38cd8 ("ARM: dts: dra72-evm-revc: add phy impedance settings")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename dmu_reserved to delta_reserved
Rename st231_dmu to st231_delta
Update the delta_reserved memory region start address
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The clock parent was lower than child clock which is not correct.
In some use case, it leads to division by zero.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Previously, the sun8i tablets used everything declared in AXP221 DTSI
while they have an AXP223 PMIC.
This corrects that so the sun8i tablets can get some features the AXP223
has (at the moment, ability to have 100mA as maximal current on VBUS
power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Allwinner Parrot R16 used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Allwinner Parrot R16 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Sinlinx SinA33 used everything declared in AXP221 DTSI
while it has an AXP223 PMIC.
This corrects that so the Sinlinx SinA33 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Previously, the Olimex A33-OlinuXino used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Olimex A33-OlinuXino can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As sti-hda is only available on STiH410-B2120,
disable it in STiH410.dtsi and enable it at board level.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
There are no Exynos4212 based boards in mainline, so there is no need to
keep additional files for SoCs, which are never used. This patch removes
support for Exynos4212 SoCs and moves previously shared Exynos4412
definitions to a single file to simplify future maintenance.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Banana Pro has an AMPAK AP6181 WiFi+Bluetooth module. The WiFi part
is a BCM43362 IC connected to MMC3 of the A20 SoC via SDIO. The IC also
takes a power enable signal via GPIO.
This commit adds a device-tree node to power it up, so the mmc subsys
can scan it, and enables the mmc controller which is connected to it.
As the wifi enable pin of the AP6181 module is not really a regulator,
switch the mmc3 node to the mmc-pwrseq framework for controlling it.
This more accurately reflectes how the hardware actually works.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC routes the LINEOUT pins to the audio out jack on the
board. The onboard microphone is routed to MIC1, with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support the audio codec found on the Allwinner H3 SoC, add
device nodes for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Q8 tablets have an internal mono speaker w/ external amp
which has a shutdown control tied to a GPIO pin. Both the speaker
amp and the headphone jack are tied to the HP output pins. While
the speaker is mono, the headset jack is stereo. Unfortunately
the driver does not support automatic switching of this.
In addition, the headset is DC coupled, or "direct drive" enabled.
The headset's microphone is tied to MIC2 with HBIAS providing power.
A separate internal microphone is tied to MIC1 with MBIAS providing
power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a device tree binding and driver for the A23's
internal audio codec, add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A23/A33, the internal codec's analog path controls are located in
the PRCM node.
Add a sub-device node to the PRCM for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UEXT are Universal EXTension connector from Olimex. They embed i2c, spi
and uart pins along power in one connector and are found on most,
if not all, Olimex boards.
The Olimex A20 SOM EVB have two UEXT connector so enable the nodes found on
those two connectors.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The spi0 controller on the A20 have up to 4 CS (Chip Select) while the
others three only have 1.
Add the num-cs property to each node.
The current driver doesn't read this property but this is useful for
downstream user of DTS (FreeBSD for example).
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use axp209.dtsi in sun7i-a20-olinuxino-lime2.dts and correct
some regulators.
DCDC2 is used for vdd-cpu so it should never be bellow 1V and above 1.4V
DCDC3 is used for VDD_INT so same as above.
LD01 is used for the RTC, and should have a typical value of 1.3V
LD02 is used for AVCC and should have a typical value of 3.0V
LD03/4 are used for Port-E/Port-G Power pin, and the schematics recommands
to set them to 2.8V as they can be used for CSI0/1.
Signed-off-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi One is a low-cost Allwinner A13-based development board, with
an AXP209 PMU, a USB2.0 OTG port, a USB2.0 host port (or an onboard
RTL8723BU Wi-Fi card), optional headers for LCD and CSI, two GPIO
headers and two MicroSD card slots (connected to mmc0 and mmc2, both
bootable).
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
