Add the SAR ADC to meson-gxbb.dtsi and meson-gxl.dtsi. GXBB provides a
10-bit ADC while GXL and GXM provide a 12-bit ADC.
Some boards use resistor ladder buttons connected through one of the ADC
channels. On newer devices (GXL and GXM) some boards use pull-ups/downs
to change the resistance (and thus the ADC value) on one of the ADC
channels to indicate the board revision.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds pinctrl group nodes for the CTS and RTS pins of each serial
controller. This makes it possible to enable the CTS and RTS pins which
are controlled by the serial controller hardware (through the meson_uart
driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the missing node for the uart_AO_B port to the meson-gx.dtsi
(as this is supported by GXBB, GXL and GXM) along with the required
pinctrl pins. This is required as some boards are using it (the boards
from the Khadas VIM series for example have it exposed on the pin
headers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SCPI and SRAM are identical on GXBB and GXL. Moving the corresponding
nodes to meson-gx adds support for the thermal sensor on GXL based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: add scpi_clocks label]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SCPI driver has an updated compatible to indicate the pre-released
(pre v1.0) status of the driver. Since Amlogic used a pre-1.0
version, add that compatible as well.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
When the USB PHY driver was introduced the reset framework did not
have support for triggering a reset pulse for shared resets. On GXBB
however there is only one reset line for both PHYs (meaning we have a
shared reset line). With the latest changes to the reset framework and
the corresponding updates to the phy-meson8b-usb2 driver we can now pass
the reset to the second PHY as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the nodes for the dwc2 USB controller and the related USB PHYs.
Currently we force usb0 to host mode because OTG is currently not
working in our PHY driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic reference driver uses the "mc_val" devicetree property to
configure the PRG_ETHERNET_ADDR0 register. Unfortunately it uses magic
values for this configuration.
According to the datasheet the PRG_ETHERNET_ADDR0 register is at address
0xc8834108. However, the reference driver uses 0xc8834540 instead.
According to my tests, the value from the reference driver is correct.
No changes are required to the board dts files because the only
required configuration option is the phy-mode, which had to be
configured correctly before as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the NVMEM device node in the DTSI.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[khilman: dropped driver cleanup hunk]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the secure monitor node in the Amlogic Meson GXBB DTSI file to
enable it.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit f3abd62961, which caused a build regression:
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi:48:41: fatal error: dt-bindings/clock/gxbb-clkc.h: No such file or directory
We should apply this patch one merge window later, once the clk branch
is merged as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT nodes for additional UARTs (UART B & C in EE domain) and add pins
for all EE domain UARTs.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add two new buses in the DTS: hiu and periphs buses.
In the Amlogic S905/GXBB SoC several devices (clock / eth / pin
controllers, etc...) are mapped under these two buses. Add them in the
DT before starting to add new devices.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them, and remove aliases to disabled devices (serial1).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
