This patch adds support to blsp2_spi5 device, which is used in some of
the APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c0, which is used on some of the
APQ8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to blsp2_i2c1, which is used in one of the
apq8096 based boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds blsp1_i2c2 support, as this bus is used on some of the
apq8096 boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds bslp2_uart2 node in soc so that boards that use this
uart can enable it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds msmgpio label for pin and gpio controller so that
it can referenced in dedicated pins file and other board level gpios.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Previous changes in this series allowed exposing the card clock from the
rk3399 SDHCI device and allowed consuming the card clock in the rk3399
eMMC PHY. Hook things up in the main rk3399 dtsi file.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rk3399 we'd like to be able to properly set corecfg registers in the
Arasan SDHCI component. Specify the syscon to enable that.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Most of the debug-related components on Juno are located in the coreSight
subsystem while others are located in the Cortex-Axx clusters, the SCP
subsystem, and in the main system.
Each core in the two processor clusters contain an Embedded Trace
Macrocell(ETM) which generates real-time trace information that trace
tools can use and an ATB trace output that is sent to a funnel before
going to the CoreSight subsystem.
The trace output signals combine with two trace expansions using another
funnel and fed into the Embedded Trace FIFO(ETF0).
The output trace data stream of the funnel is then replicated before it
is sent to either the:
- Trace Port Interface Unit(TPIU), that sends it out using the trace port.
- ETR that can write the trace data to memory located in the application
memory space
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Adds the cache nodes and next-level-cache property for the
cacheinfo to work.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds the cache nodes and next-level-cache property for the
cacheinfo to work.
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The convention in these files is to use lowercase for "0x" prefixes and for
the hex constants themselves, but a few changes didn't follow that
convention, which makes the file annoying to read.
Use lowercase consistently for the hex constants. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Duc Dang <dhdang@apm.com>
This pull request contains Device Tree changes for Broadcom ARM64-based SoCS:
- Anup adds nodes for the AHCI and SATA3 PHY peripherals to the Northstar2 SoCs
- Dhanajay enables pinctrl for the Northstar2 SoCs
- Jon Mason enables all of the UART peripherals found in the NS2 SVK and
finally adds the CCI-400 and PMU nodes
* tag 'arm-soc/for-4.8/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: NS2: Add CCI-400 PMU support
arm64: dts: NS2: Add all of the UARTs
arm64: dts: Enable GPIO for Broadcom NS2 SoC
arm64: dts: enable pinctrl for Broadcom NS2 SoC
arm64: dts: Add SATA3 AHCI and SATA3 PHY DT nodes for NS2
dt-bindings: ata: add compatible string for iProc AHCI controller
Signed-off-by: Olof Johansson <olof@lixom.net>
The 2nd additional region is the GIC virtual cpu interface register
base and size.
As the gic400 of rk3368 says, the cpu interface register map as below
:
-0x0000 GICC_CTRL
.
.
.
-0x00fc GICC_IIDR
-0x1000 GICC_IDR
Obviously, the region size should be greater than 0x1000.
So we should make sure to include the GICC_IDR since the kernel will access
it in some cases.
Fixes: b790c2cab5 ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Cc: stable@vger.kernel.org
[added Fixes and stable-cc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We've got 9 (count em!) i2c controllers on rk3399, some of which are in
the PMU power domain and some of which are normal peripherals. Add them
all to the main rk3399 dtsi file so future patches can turn them on in
the board dts files.
Note: by default we try to set the i2c clock rate to 200 MHz so that we
can achieve good i2c functional clock rates. 200 MHz gives us the
ability to make very close to 100 kHz / 400 kHz / 1 MHz rates. If
boards want to tune clock rates further they can always override.
Possibly boards could want to tune this if:
- they wanted to save an infinitesimal amount of power and they knew
their i2c bus was slow anyway. Since we gate the functional clock
when the i2c bus is not active, power savings would only be while i2c
transfers were happening and probably won't be very big anyway.
- they wanted to eek out a bit more speed by carefully tuning the source
clock to make divisions work out perfectly, accounting for the rise /
fall time measured on an actual board.
Note also that we still request 200 MHz for the PMU i2c busses even
though we expect that we won't make that exactly (currently PPLL is 676
MHz which gives us 169 MHz).
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
[dianders: wrote desc; put in assigned-clocks; reordered nodes]
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The 'dma-coherent' indicates that the hardware IP block can ensure
the coherency of the data transferred from/to the IP block. This
can avoid the software cache flush/invalid actions, and improve
the performance significantly.
The PCI IP block of ls1043a has this capability, so adding this
feature to improve the PCI performance.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At first, 256 byte of the head of DRAM space was reserved for some
reasons. However, as the progress of development, it turned out
unnecessary, and it was never used in the end. Move the CPU release
address to leave no space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This node consists of various system-level configuration registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Update reserved-memory in accordance with memory the detailed memory map
for 8916, so that we will be able to reference the firmware memory
regions.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables bam dma node, dma is used for both tx and rx on spi
and on high speed serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add integrated MDIO multiplexer driver node which contains
two mux PCIe bus and one ethernet bus along with phys
lying on these bus.
Signed-off-by: Pramod Kumar <pramod.kumar@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPIDR_EL1[63:32] value is equal to 0 for the CPUs of the LS1043A and
LS2080A SoCs. The ARM CPU binding allows #address-cells to be set to 1,
since MPIDR_EL1[63:32] bits are not used for CPUs identification. Update
the #address-cells and reg properties accordingly.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While this devicetree also works for booting in 32-bit mode, it's
placed in arm64 since it's a 64-bit CPU (as suggested by Arnd).
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org> (v1)
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
LS1043A has a SEC v5.4 security engine.
For now don't add rtic or sec_mon subnodes, since these features
haven't been tested yet.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
