Add initial dtsi files to support Marvell Armada 3700 SoC with Cortex-A53
CPUs. There are two members in this family: the Armada 3710 (Single CPU)
and the Armada 3720 (Dual CPUs).
It also adds a dts file for the Marvell Armada 3720 DB board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a device node for the Cortex-A53 L2 cache-controller.
The L2 cache for the Cortex-A53 CPU cores is 512 KiB large (organized as
32 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add "snps,quirk-frame-length-adjustment" property to USB3 node for
erratum A009116. This property provides value of GFLADJ_30MHZ for post
silicon frame length adjustment.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ARM's Juno platforms have two HDLCD controllers, each linked to an NXP
TDA19988 HDMI transmitter that provides output encoding. Add them
to the device tree.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Keyboard driver for GPIO buttons(gpio-keys) checks for the legacy
"gpio-key,wakeup" boolean property to enable gpio buttons as wakeup
source.
Few dts files assign value "1" to gpio-key,wakeup and in one instance a
value "0" is assigned probably assuming it won't be enabled as a wakeup
source. Since the presence of the boolean property indicates it is
enabled, value of "0" have no value.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property which inturn fixes the above mentioned issue.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The PCIe controller is found on all Juno SoC version. However it's not
functional on R0 due to some hardware bug.
In preparation to add Juno R2 support, this patch moves the
pcie-controller defination to base DTS file. It's marked as disabled by
default and is enabled for Juno R1 explicitly.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The ARMv8 Foundation model sports a command line parameter to use
a GICv3 emulation instead of the default GICv2 interrupt controller.
Add a new .dts file which reuses most of the definitions of the
existing model while just adding the required properties for the
GICv3 node.
This allows the public Foundation model to run with a GICv3.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The ARMv8 Foundation model can be run with a GICv2 or a GICv3.
To prepare for the GICv3 version of the .dts without code duplication,
move most of the nodes of the existing DT (except the GIC) into an
include file and just keep that include statement and the GIC node in
the current foundation-v8.dts.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Foundation model GIC mapping is wrong, as the GICC region should
be 8kB instead of 4kB (the model implements the GICv2 architecture).
This defect prevents the driver from switching to EOImode==1.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
To prepare the ARM foundation model to support GICv3, we adjust
the #address-cells property of the current GICv2 node to be
compatible with the two cells required for GICv3 later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add device tree file for AMD/Linaro 96Boards Enterprise Edition Server
(Husky) Board. This is based on the AMD Seattle Rev.B0 system
Signed-off-by: Leo Duran <leo.duran@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device tree files for AMD Overdrive boards which comes with
AMD Seattle Revision B0 and B1 SOCs.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add AMD XGBE device tree file, which is available in AMD Seattle RevB.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix DMA ranges of smb0 and pcie0 nodes in AMD Seattle SOC.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes incorrect sizes of the GICv2 device tree node.
This has triggered error message when booting Xen hypervisor.
Signed-off-by: Brijesh Singh <brijeshkumar.singh@amd.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Instead of using the generic armv8-pmuv3 compatibility use the more
specific Cortex A57 compatibility.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
Add device nodes for the L2 caches, and link the CPU node to its L2
cache node.
The L2 cache for the Cortex-A57 CPU cores is 2 MiB large (organized as
128 KiB x 16 ways).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates:
- SCIF:
- Supports now 50, 230400, 460800, 500000, and 921600 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
- HSCIF:
- Supports now 50, 75, and 110 bps,
- Perfect match for standard 50-460800, and 9216000 bps.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device node for the external SCIF_CLK.
The presence of the SCIF_CLK crystal and its clock frequency depend on
the actual board.
Add the two optional clock sources (S3D1 and SCIF_CLK for the internal
resp. external clock) for the Baud Rate Generator for External Clock
(BRG) to all SCIF and HSCIF device nodes.
This increases the range and accuracy of supported baud rates on
(H)SCIF.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
vexpress fixes for v4.5
Couple of minor fixes for vexpress platforms:
1. Add missing of_node_put in vexpress config bus
2. Add missing DMA-330 abort interrupt on Juno platforms
* tag 'vexpress-for-v4.5/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
The NVIDIA bootloader, nvtboot, expects the "chosen" node to be present
in the device-tree blob and if it is not then it fails to boot the kernel.
Add the chosen node so we can boot the kernel on Tegra132 Norrin with the
nvtboot bootloader.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The DMA-330 has an "irq_abort" interrupt line on which it signals faults
separately from the "irq[n:0]" channel interrupts. On Juno, this is
wired up to SPI 92; add it to the DT so that DMAC faults are correctly
reported for the driver to reset the thing, rather than leaving it
locked up and waiting to time out.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add tuning clk for emmc and sdmmc, otherwise I get
the following failure while enabling mmc-hs200-1_8v.
dwmmc_rockchip ff0f0000.dwmmc: Tuning clock (sample_clk) not defined.
mmc0: tuning execution failed
mmc0: error -5 whilst initialising MMC card
With it
dwmmc_rockchip ff0f0000.dwmmc: Successfully tuned phase to 170
mmc0: new HS200 MMC card at address 0001
mmcblk0: mmc0:0001 M8G1GC 7.28 GiB
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
