Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: Eduard Gavin <egavinc@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.
The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.
So, the initialization sequence is as follows:
1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.
This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
error: implicit declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some user space use cases result in kernel hangup on the HIC_OPEN_SENSOR
command write. In case when a minimalistic application is used for setting
up the streaming, the hangups occur only occasionally. In case of GStreamer
use cases it is always the case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to allow for automatic media device entities linking
from the level of libv4l plugin the open system call shouldn't
fail, as the libv4l plugins can begin their job not until it
succeeds.
This patch allows for leaving the pipeline not linked on
open and postpones verifying it to the moment when streamon
callback is called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
VIDIOC_SUBDEV_G_FMT ioctl should return TRY format previously
set with VIDIOC_SUBDEV_S_FMT. Currently it is not the case as
only ACTIVE formats are saved in the driver. Since the driver
doesn't alter hardware state in the set_fmt op anyway, the
op can save the format in both TRY and ACTIVE case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ironically, 7d4020c3c4 ("[media] exynos4-is: fix some warnings when
compiling on arm64") fixed some format string bugs but introduced a
new one. buf_index is a simple int, so it should be printed with %d,
not %pad (which is correctly used for dma_addr_t).
Fixes: 7d4020c3c4 ("[media] exynos4-is: fix some warnings when compiling on arm64")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was found with the -RT patch enabled, but the fix should apply to
non-RT also.
Compilation error without this fix:
../drivers/media/platform/vsp1/vsp1_video.c: In function
'vsp1_pipeline_stopped':
../drivers/media/platform/vsp1/vsp1_video.c:524:2: error: expected
expression before 'do'
spin_unlock_irqrestore(&pipe->irqlock, flags);
^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_subdev_sensor_ops structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.
This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum isp_pipeline_state versus
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Control framework now requires entities to be registered with
the media device before creating links so commit c7621b3044 ("[media]
v4l: vsp1: separate links creation from entities init") separated link
creation from entities init.
But unfortunately that patch introduced a regression since wrong links
were created causing a boot failure on Renesas boards.
This patch fixes the boot issue and also the media graph was compared
by Geert Uytterhoeven to make sure that the driver changes required by
the Media Control framework next generation did not affect the graph.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
Pull second batch of media updates from Mauro Carvalho Chehab:
"This is the second part of the media patches. It contains the media
controller next generation patches, with is the result of one year of
discussions and development. It also contains patches to enable media
controller support at the DVB subsystem.
The goal is to improve the media controller to allow proper support
for other types of Video4Linux devices (radio and TV ones) and to
extend the media controller functionality to allow it to be used by
other subsystems like DVB, ALSA and IIO.
In order to use the new functionality, a new ioctl is needed
(MEDIA_IOC_G_TOPOLOGY). As we're still discussing how to pack the
struct fields of this ioctl in order to avoid compat32 issues, I
decided to add a patch at the end of this series commenting out the
new ioctl, in order to postpone the addition of the new ioctl to the
next Kernel version (4.6).
With that, no userspace visible changes should happen at the media
controller API, as the existing ioctls are untouched. Yet, it helps
DVB, ALSA and IIO developers to develop and test the patches adding
media controller support there, as the core will contain all required
internal changes to allow adding support for devices that belong to
those subsystems"
* tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (177 commits)
[media] Postpone the addition of MEDIA_IOC_G_TOPOLOGY
[media] mxl111sf: Add a tuner entity
[media] dvbdev: create links on devices with multiple frontends
[media] media-entitiy: add a function to create multiple links
[media] dvb-usb-v2: postpone removal of media_device
[media] dvbdev: Add RF connector if needed
[media] dvbdev: remove two dead functions if !CONFIG_MEDIA_CONTROLLER_DVB
[media] call media_device_init() before registering the V4L2 device
[media] uapi/media.h: Use u32 for the number of graph objects
[media] media-entity: don't sleep at media_device_register_entity()
[media] media-entity: increase max number of PADs
[media] media-entity.h: document the remaining functions
[media] media-device.h: use just one u32 counter for object ID
[media] media-entity.h fix documentation for several parameters
[media] DocBook: document media_entity_graph_walk_cleanup()
[media] move documentation to the header files
[media] media: Move MEDIA_ENTITY_MAX_PADS from media-entity.h to media-entity.c
[media] media: Remove pre-allocated entity enumeration bitmap
[media] staging: v4l: davinci_vpbe: Use the new media graph walk interface
[media] staging: v4l: omap4iss: Use the new media graph walk interface
...
Pull media updates from Mauro Carvalho Chehab:
"The part of patches for Kernel 4.5. There's nothing really big here:
- driver-specific headers for media devices were moved to separate
directories, in order to make clear what headers belong to the core
kABI and require documentation
- Platform data for media drivers were moved from include/media to
include/linux/platform_data/media
- add a driver for cs3308 8-channel volume control, used on some
high-end capture boards
- lirc.h kAPI header were added at include/uapi/linux
- Driver cleanups, new board additions and improvements"
* tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
There are a few discussions left with regards to this ioctl:
1) the name of the new structs will contain _v2_ on it?
2) what's the best alternative to avoid compat32 issues?
Due to that, let's postpone the addition of this new ioctl to
the next Kernel version, to give people more time to discuss it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While mxl111sf may have multiple frontends, it has just one
tuner. Reflect that on the media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices like mxl111sf-based WinTV Aero-m have multiple
frontends, all linked on the same demod. Currently, the
dvb_create_graph() function is not smart enough to create
multiple links. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes, it is desired to create 1:n and n:1 or even
n:n links between different entities with the same
function.
This is actually needed to support DVB devices that
have multiple frontends. While we could do a function
like that internally at the DVB core, such function is
generic enough to be at media-entity, and it could be
useful on some other places.
So, add such function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not remove the media_device until its last usage,
or we may have use after free troubles.
So, move the per-adapter media_device removal to happen at
the end of the adapter removal code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several pure digital TV devices have a frontend with the tuner
integrated on it. Add the RF connector when dvb_create_media_graph()
is called on such devices.
Tested with siano and dvb_usb_mxl111sf drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those functions are used only if CONFIG_MEDIA_CONTROLLER_DVB.
Without that, if !CONFIG_MEDIA_CONTROLLER_DVB, it would produce
two warnings:
drivers/media/dvb-core/dvbdev.c:219:12: warning: 'dvb_create_tsout_entity' defined but not used [-Wunused-function]
static int dvb_create_tsout_entity(struct dvb_device *dvbdev,
^
drivers/media/dvb-core/dvbdev.c:264:12: warning: 'dvb_create_media_entity' defined but not used [-Wunused-function]
static int dvb_create_media_entity(struct dvb_device *dvbdev,
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, v4l2_device_register() doesn't use the media_device
struct. So, calling media_device_init() could be called either
before or after v4l2_device_register().
Yet, it is a good practice to initialize everything before calling
the register functions. Also, the other drivers call
media_device_init() before registering the V4L2 device.
So, move the call for media_device_init() to happen earlier on
exynos4-is and s3c-camif.
This is just a cleanup patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB drivers may have 257 PADs. Get the next power of two
that would accomodate that amount.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using one u32 counter per type for object IDs, use
just one counter. With such change, it makes sense to simplify
the debug logs too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some exported functions were still documented at the .c file,
instead of documenting at the .h one.
Move the documentation to the right place, as we only use headers
at media device-drivers.xml DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This isn't really a part of any interface drivers are expected to use. In
order to keep drivers from using it, hide it in media-entity.c. This was
always an arbitrary number and should be removed in the long run.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bitmaps for entity enumerations used to be statically allocated. Now
that the drivers have been converted to use the new interface which
explicitly initialises the enum objects, drop the pre-allocated bitmaps.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
