The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver has hit a parity event, HW can no longer write to host memory.
As a result, Tx completions cannot be written to the host SB memory, and
waiting for Tx completions eventually timeout.
As driver is willing to delay as much as 1-2 seconds per Tx queue for its
draining and this delay is sequential, the time to recover might greatly
lengthen needlessly in case the recovery is done under multi-connection
traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW has a rare corner case in which a fragmented packet using lots
of frags would not be linearized, causing the FW to assert while trying
to transmit the packet.
To prevent this, we need to make sure the window of fragements containing
MSS worth of data contains 1 BD less than for regular packets due to
the additional parsing BD.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fields are updated but never read.
Remove the overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy TX load, bnx2x_poll() can loop forever and trigger
soft lockup bugs.
A napi poll handler must yield after one TX completion round,
risk of livelock is too high otherwise.
Bug is very easy to trigger using a debug build, and udp flood, because
of added cpu cycles in TX completion, and we do not receive enough
packets to break the loop.
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's supposed to be impossible for TPA to give us anything else
than IPv4 or IPv6 here. But in case there is a way to reach this error
by some strange received frames, we don't want to flood the kernel log.
WARN_ONCE is better for this purpose.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_pages() already prints a warning when it fails. No need to emit
another message. Certainly not at KERN_ERR level, because it is no big
deal if this GFP_ATOMIC allocation fails occasionally.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Management firmware tells driver in case bandwidth configuration for
a specific function exists, but [regretably] the same field has different
meanings depending on the multi-function mode - it can either be
a percentile value or an actual speed.
For newer multi-function modes current logic is incorrect -
driver understands values as actual speeds instead of percentages,
causing the resulting chip configuration to be incorrect.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver always uses vlan-promisc mode, i.e., it receives both
tagged and untagged traffic and lets the network stack drop packets
tagged with unrequested vlan tags.
This patch implements vlan-filtering offload in the driver -
Unless explicitly configured to promisc mode, only untagged packets or
packets tagged with requested vlans would reach the Rx flow.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with up-to-date management FW will be able to store register dumps
on their persistent storage - in case management FW identifies a fatal
error it would gather and store such dumps, which could later be retrieved
using specific debug tools.
This patch adds the necessary part in the driver in order to make the
feature operational, as well as update users [under debug] during load
in case their device contains a dump of a previous crash.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support to a new multi-function mode, enabling driver to
initialize such devices and correctly interacting with management FW
for fully utilizing their features.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x still appears as a Broadcom driver even though the devices it
utilizes belong to Qlogic for more than a year.
This patch changes the various headers and the device strings to indicate
the correct ownership of the device.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves bnx2x into using 7.12.30 FW. Said firmware fixes the following:
- Packets from a VF with pvid configured which were sent with a
different vlan were transmitted instead of being discarded.
- FCoE traffic might not recover after a failue while there's traffic
to another function.
In addition, this FW opens the door for the driver to implement several
new features; Specifically, this enhances the device's support for
encapsulated packets and will allow vxlan/geneve offloads to be added in
the future, as well as vlan filtering offload.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DMA_API_DEBUG=y bnx2x triggers the error "DMA-API: device
driver frees DMA memory with wrong function".
On archs where PAGE_SIZE > SGE_PAGE_SIZE it also triggers "DMA-API:
device driver frees DMA memory with different size".
Fix this by making the mapping and unmapping symmetric:
- Do not map the whole pool page at once. Instead map the
SGE_PAGE_SIZE-sized pieces individually, so they can be unmapped in
the same manner.
- What's mapped using dma_map_page() must be unmapped using
dma_unmap_page().
Tested on ppc64.
Fixes: 4cace675d6 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.
For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver allocates one page for each buffer on the rx ring, which is
too much on architectures like ppc64 and can cause unexpected allocation
failures when the system is under stress. Now, we keep a memory pool
per queue, and if the architecture's PAGE_SIZE is greater than 4k, we
fragment pages and assign each 4k segment to a ring element, which
reduces the overall memory consumption on such architectures. This
helps avoiding errors like the example below:
[bnx2x_alloc_rx_sge:435(eth1)]Can't alloc sge
[c00000037ffeb900] [d000000075eddeb4] .bnx2x_alloc_rx_sge+0x44/0x200 [bnx2x]
[c00000037ffeb9b0] [d000000075ee0b34] .bnx2x_fill_frag_skb+0x1ac/0x460 [bnx2x]
[c00000037ffebac0] [d000000075ee11f0] .bnx2x_tpa_stop+0x160/0x2e8 [bnx2x]
[c00000037ffebb90] [d000000075ee1560] .bnx2x_rx_int+0x1e8/0xc30 [bnx2x]
[c00000037ffebcd0] [d000000075ee2084] .bnx2x_poll+0xdc/0x3d8 [bnx2x] (unreliable)
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Reviewed-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Submit 909d9faae2 ("bnx2x: Prevent inner-reload while VFs exist")
contained a bug - MTU change was not prevented by it; Instead, it
`randomally' prevented bnx2x_resume() from running [harmless yet wrong].
This moves the check to its correct spot.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are redundant with dev->features. Remove them.
Just make sure to set dev->features ourselves in bnx2x_set_features()
before performing the reload of the card.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is simpler to have the TPA mode as one three-state variable.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If disable_tpa is set, remove NETIF_F_LRO from hw_features, so ethtool sees
it as "off [fixed]".
Note that setting the NETIF_F_LRO bit in dev->features in the 'else'
branch is not needed, because the bit was already set by
bnx2x_init_dev().
Then the check for disable_tpa in in bnx2x_fix_features() becomes unnecessary.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.
Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.
The bug was an unintended consequence of commit aebf6244cd "bnx2x: Be
more forgiving toward SW GRO".
Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some feature changes, driver employes an inner-reload flow where it
resets the function and re-configures it with the new required set of
parameters.
Such a flow proves fatal to any VF since those were not intended to be used
while HW is being reset underneath, causing them [at best] to lose all
connectivity.
This changes driver behavior to fail all configuration changes [e.g., mtu
change] requested of the driver in case VFs are active.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9a2620c877 ("bnx2x: prevent WARN during driver unload")
switched the napi/busy_lock locking mechanism from spin_lock() into
spin_lock_bh(), breaking inter-operability with netconsole, as netpoll
disables interrupts prior to calling our napi mechanism.
This switches the driver into using atomic assignments instead of the
spinlock mechanisms previously employed.
Based on initial patch from Yuval Mintz & Ariel Elior
I basically added softirq starvation avoidance, and mixture
of atomic operations, plain writes and barriers.
Note this slightly reduces the overhead for this driver when no
busy_poll sockets are in use.
Fixes: 9a2620c877 ("bnx2x: prevent WARN during driver unload")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit d75b1ade56 ("net: less interrupt masking in NAPI") napi
repoll is done only when work_done == budget. When in busy_poll is we return 0
in napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_msix_fp_int() and bnx2x_interrupt() run from hard interrupt
context.
They can use napi_schedule_irqoff() instead of napi_schedule()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange macros to query for storage-only modes in different MF environment.
Improves the readibility and maintainability of the code. E.g.:
- if (IS_MF_STORAGE_SD(bp) || IS_MF_FCOE_AFEX(bp))
+ if (IS_MF_STORAGE_ONLY(bp))
In addition, this removes the need for bnx2x_is_valid_ether_addr().
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a sprase warning introduced recently by commit
eeed018cbf ("bnx2x: Add timestamping and PTP hardware clock support"),
as well as another unrelated sparse endian issue.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
