Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should keep one way to build skbs, regardless of GRO being on or off.
Note that I made sure to defer as much as possible the point we need to
pull data from the frame, so that future prefetch() we might add
are more effective.
These skb attributes derive from the CQE or ring :
ip_summed, csum
hash
vlan offload
hwtstamps
queue_mapping
As a bonus, this patch removes mlx4 dependency on eth_get_headlen()
which is very often broken enough to give us headaches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing a boolean in fast path is not worth duplicating
the code allocating packets, when GRO is on or off.
If this proves to be a problem, we might later use a jump label.
Next patch will remove this duplicated code and ease code review.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to compute the frame virtual address at different points.
Do it once.
Following patch will use the new va address for validate_loopback()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of fetching dma address from rx_desc->data[0].addr,
prefer using frags[0].dma + frags[0].page_offset to avoid
a potential cache line miss.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new counter tracks number of pages that we allocated for one port.
lpaa24:~# ethtool -S eth0 | egrep 'rx_alloc_pages|rx_packets'
rx_packets: 306755183
rx_alloc_pages: 932897
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same technique than some Intel drivers, for arches where PAGE_SIZE = 4096
In most cases, pages are reused because they were consumed
before we could loop around the RX ring.
This brings back performance, and is even better,
a single TCP flow reaches 30Gbit on my hosts.
v2: added full memset() in mlx4_en_free_frag(), as Tariq found it was needed
if we switch to large MTU, as priv->log_rx_info can dynamically be changed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of order-3 pages is problematic in some cases.
This patch might add three kinds of regression :
1) a CPU performance regression, but we will add later page
recycling and performance should be back.
2) TCP receiver could grow its receive window slightly slower,
because skb->len/skb->truesize ratio will decrease.
This is mostly ok, we prefer being conservative to not risk OOM,
and eventually tune TCP better in the future.
This is consistent with other drivers using 2048 per ethernet frame.
3) Because we allocate one page per RX slot, we consume more
memory for the ring buffers. XDP already had this constraint anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon use order-0 pages, and frag truesize will more precisely
match real sizes.
In the new model, we prefer to use <= 2048 bytes fragments, so that
we can use page-recycle technique on PAGE_SIZE=4096 arches.
We will still pack as much frames as possible on arches with big
pages, like PowerPC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using per frag storage for frag_prefix_size is really silly.
mlx4_en_complete_rx_desc() has all needed info already.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is really a port attribute, no need to duplicate it per
RX queue and per frag.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate it for all queues and frags.
num_frags & log_rx_info become u8 to save space.
u8 accesses are a bit faster than u16 anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cited commit makes a great job of finding optimal shift/multiplier
values assuming a 10 seconds wrap around, but forgot to change the
overflow_period computation.
It overflows in cyclecounter_cyc2ns(), and the final result is 804 ms,
which is silly.
Lets simply use 5 seconds, no need to recompute this, given how it is
supposed to work.
Later, we will use a timer instead of a work queue, since the new RX
allocation schem will no longer need mlx4_en_recover_from_oom() and the
service_task firing every 250 ms.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or we might miss the fact that a page was allocated from memory reserves.
Fixes: dceeab0e52 ("mlx4: support __GFP_MEMALLOC for rx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating EQs to handle CQ completion events for the PF
or for VFs, we create enough EQE entries to handle completions
for the max number of CQs that can use that EQ.
When SRIOV is activated, the max number of CQs a VF (or the PF) can
obtain is its CQ quota (determined by the Hypervisor resource tracker).
Therefore, when creating an EQ, the number of EQE entries that the VF
should request for that EQ is the CQ quota value (and not the total
number of CQs available in the FW).
Under SRIOV, the PF, also must use its CQ quota, because
the resource tracker also controls how many CQs the PF can obtain.
Using the FW total CQs instead of the CQ quota when creating EQs resulted
wasting MTT entries, due to allocating more EQEs than were needed.
Fixes: 5a0d0a6161 ("mlx4: Structures and init/teardown for VF resource quotas")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the VF driver, module parameter mlx4_log_num_mgm_entry_size was
mistakenly overwritten -- and in a manner which overrode the
device-managed flow steering option encoded in the parameter.
log_num_mgm_entry_size is a global module parameter which
affects all ConnectX-3 PFs installed on that host.
If a VF changes log_num_mgm_entry_size, this will affect all PFs
which are probed subsequent to the change (by disabling DMFS for
those PFs).
Fixes: 3c439b5586 ("mlx4_core: Allow choosing flow steering mode")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spoofcheck can't be enabled if VF MAC is zero.
Vice versa, can't zero MAC if spoofcheck is on.
Fixes: 8f7ba3ca12 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlx4 NIC are used on PowerPC with 64K pages, we need to adapt
MLX4_EN_ALLOC_PREFER_ORDER definition.
Otherwise, a fragment sitting in an out of order TCP queue can hold
0.5 Mbytes and it is a serious OOM risk.
Fixes: 51151a16a6 ("mlx4: allow order-0 memory allocations in RX path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) In the case where rate == priv->pkt_rate_low == priv->pkt_rate_high,
mlx4_en_auto_moderation() does a divide by zero.
2) We want to properly change the moderation parameters if rx_frames
was changed (like in ethtool -C eth0 rx-frames 16)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All rx and rx netdev interrupts are handled by respectively
by mlx4_en_rx_irq() and mlx4_en_tx_irq() which simply schedule a NAPI.
But mlx4_eq_int() also fires a tasklet to service all items that were
queued via mlx4_add_cq_to_tasklet(), but this handler was not called
unless user cqe was handled.
This is very confusing, as "mpstat -I SCPU ..." show huge number of
tasklet invocations.
This patch saves this overhead, by carefully firing the tasklet directly
from mlx4_add_cq_to_tasklet(), removing four atomic operations per IRQ.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a reader-writer lock in fast path is silly, when we can
instead use RCU or a seqlock.
For mlx4 hwstamp clock, a seqlock is the way to go, removing
two atomic operations and false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08
The problem is the same as what was described in commit ec13ee8014
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.
Fixes: 07841f9d94 ("net/mlx4_en: Schedule napi when RX buffers allocation fails")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f735 ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling mlx4_en_try_alloc_resources (e.g. by changing the
number of rx-queues with ethtool -L), the existing xdp_prog becomes
inactive.
The bug is that the xdp_prog ptr has not been carried over from
the old rx-queues to the new rx-queues
Fixes: 47a38e1550 ("net/mlx4_en: add support for fast rx drop bpf program")
Cc: Brenden Blanco <bblanco@plumgrid.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
The result is that the VF driver on the VM will experience a command
timeout during the shutdown process when the Hypervisor does not deliver
a command-completion event to the VM.
To avoid FW command timeouts on the VM when the driver's shutdown method
is invoked, we detect the absence of the VF's comm channel at the very
start of the shutdown process. If the comm-channel has already been
disabled, we cause all FW commands during the device shutdown process to
immediately return success (and thus avoid all command timeouts).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure pptx/pprx mask flag is set using new fields upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure MTU mask flag is set using new field upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the port, driver will inform Firmware about the actual MTU
which does not include implicit headers, such as FCS or VLAN tags.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.
This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reading num_tc directly from struct net_device, but use
the helper function netdev_get_num_tc.
Fixes: bc6a4744b8 ("net/mlx4_en: num cores tx rings for every UP")
Fixes: f5b6345ba8 ("net/mlx4_en: User prio mapping gets corrupted when changing number of channels")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to aid debugging of functions that take a resource but
don't put it, add the last function name that successfully grabbed
this resource.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device revision field returned by the NodeInfo MAD is incorrect
on ConnectX3 devices.
This patch is driver side handling to complete a FW fix added at 2.11.1172.
INIT_HCA - bit at offset 0x0C.12 is set to 1 so that FW will report
correct device revision.
Older FW versions won't be affected from turning on that bit,
no capability bit is needed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conform the following warning:
WARNING: ENOSYS means 'invalid syscall nr' and nothing else.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the code clearer, use rb_entry() instead of container_of() to
deal with rbtree.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 04aeb56a17 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boundaries checks for the number of RX, TX, other and combined channels
should be checked by the caller and not in the driver.
In addition, remove wrong memset on get channels as it overrides the cmd
field in the requester struct.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running SRIOV, warnings for SRQ LIMIT events flood the Hypervisor's
message log when (correct, normally operating) apps use SRQ LIMIT events
as a trigger to post WQEs to SRQs.
Add more information to the existing debug printout for SRQ_LIMIT, and
output the warning messages only for the SRQ CATAS ERROR event.
Fixes: acba2420f9 ("mlx4_core: Add wrapper functions and comm channel and slave event support to EQs")
Fixes: e0debf9cb5 ("mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Save the qp context flags byte containing the flag disabling vlan stripping
in the RESET to INIT qp transition, rather than in the INIT to RTR
transition. Per the firmware spec, the flags in this byte are active
in the RESET to INIT transition.
As a result of saving the flags in the incorrect qp transition, when
switching dynamically from VGT to VST and back to VGT, the vlan
remained stripped (as is required for VST) and did not return to
not-stripped (as is required for VGT).
Fixes: f0f829bf42 ("net/mlx4_core: Add immediate activate for VGT->VST->VGT")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
