Acquire NVM lock before reads on all devices. Previously, locks were
only used for X722 and later. Fixes an issue where simultaneous X710
NVM accesses were interfering with each other.
Change-ID: If570bb7acf958cef58725ec2a2011cead6f80638
Signed-off-by: Aaron Salter <aaron.k.salter@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Missing in the initial submission, qed fails to propagate qedi's
request to enable OOO to firmware.
Fixes: fc831825f9 ("qed: Add support for hardware offloaded iSCSI")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set the number of entries in database, otherwise the logic
would quickly surpass the array.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before iterating over the the LL2 Rx ring, the ring's
spinlock is taken via spin_lock_irqsave().
The actual processing of the packet [including handling
by the protocol driver] is done without said lock,
so qed releases the spinlock and re-claims it afterwards.
Problem is that the final spin_lock_irqrestore() at the end
of the iteration uses the original flags saved from the
initial irqsave() instead of the flags from the most recent
irqsave(). So it's possible that the interrupt status would
be incorrect at the end of the processing.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
CC: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an Rx LL2 packet, qed fails to unmap the previous buffer.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support");
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current Logic would allow the creation of a chain with U32_MAX + 1
elements, when the actual maximum supported by the driver infrastructure
is U32_MAX.
Fixes: a91eb52abb ("qed: Revisit chain implementation")
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Doorbell HW block can be configured at a granularity
of 16 x CIDs, so we need to make sure that the actual number
of CIDs configured would be a multiplication of 16.
Today, when RoCE is enabled - given that the number is unaligned,
doorbelling the higher CIDs would fail to reach the firmware and
would eventually timeout.
Fixes: dbb799c397 ("qed: Initialize hardware for new protocols")
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255.
This fixes vlans learning not being enabled for wider ranges than 255.
Fixes: a4feea74cd ("mlxsw: reg: Add Switch Port VLAN MAC Learning register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The num_rec field is 8 bit, so the maximal count number is 255. This
fixes vlans not being enabled for wider ranges than 255.
Fixes: b2e345f9a4 ("mlxsw: reg: Add Switch Port VID and Switch Port VLAN Membership registers definitions")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds support for the GENETv5 implementation.
The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver. Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit changes the ioctl handling behavior to return the
EOPNOTSUPP error code instead of the EINVAL error code when an
unknown ioctl command value is detected.
It also removes some redundant parsing of the ioctl command value
and allows the SIOCSHWTSTAMP value to be handled.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reclaim function should return the number of buffer descriptors
reclaimed, not just the number corresponding to skb packets.
Also, remove the unnecessary computation when updating the consumer
index.
While this is not a functional problem it could degrade performance
of napi in a fragmented transmit stream.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the DMA interrupt status is latched and the DMA servicing can be
polled, it is a good idea to clear the latched status of a DMA interrupt
before performing the service that would be invoked by the interrupt.
This prevents old status from causing spurious interrupts when the
interrupt is unmasked at a later time.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcmgenet_wol_isr() handler performs the necessary processing for
waking from a GENET event. There is no necessary functionality behind
servicing the UMAC_IRQ_MPD_R event in the handling of isr0. Therefore
the code that unmasks and masks this interrupt and that gets invoked
in response to it is removed by this commit.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit moves DMA interrupt enabling out of init_umac() and adds
the masking of these interrupts to the napi enable and disable code.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An assortment of non-functional lines are removed to reduce confusion
and some typos in comments are corrected.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A 2's complement subtraction will always do a borrow, so masking
off the sign bits is the same as conditionally adding (mask+1).
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.
It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.
In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].
Changes from Previous versions:
-------------------------------
- V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the rx queue default size when dma interrupts are treated,
since dma op mode can be also set there.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures default number of RX and TX queues when
using the pci glue driver.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace init_timer with setup_timer to simplify the source code.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TC flower offload statistics including number of packets,
bytes and last use timestamp. Currently the statistics are gathered on a
per-rule basis.
Signed-off-by: Arkadi Sharshvesky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for packets and byte statistics on TCAM entries. The counters
are allocated from the generic flow counters pool.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Policing and Counting action block. This action block
will be used to bind counter to TCAM entries.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce periodic task for dumping the activity status for the ACL
rule TCAM entries. This is done in order to emulate last use statistics.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.comi>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ACL rules can be accessed only by hashing. In order to
dump the activity the rules are also placed in a list.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for retrieving TCAM entry activity. In order to support ACL
rule activity corresponding TCAM entry should be queried.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for allocating generic flow counter. Generic flow counter
can count packets or packets and bytes and can be assigned to different
hardware processes. First use will be for counting packets and bytes of
ACL rules, and will be introduced in the following patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add implementation for counter allocator. The ASIC has special memory
pool for various counting purposes. Counter memory is distributed between
equal size banks.
The static sub-pool configuration should specify the following parameters
for each sub-pool:
- Number of required banks.
- Maximum entry size.
Each module can add dedicated sub-pool or use existing one.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support prepending data from XDP. We are already always allocating
some headroom because FW may prepend metadata to packets.
xdp_adjust_head() can be supported by making sure that headroom is
big enough for XDP. In case FW had prepended metadata to the packet,
however, we have to move it out of the way before we call XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP may require us to move metadata to make room for pushing
headers. Track meta data location with a pointer and pass
it explicitly to functions.
While at it validate that meta_len from the descriptor is not
bogus.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename pkt_off variable to dma_off, it should hold data offset
counting from beginning of DMA mapping. Compute the value only
in XDP context.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP_NET_CFG_RX_OFFSET is 32bit wide, make sure what we read from
there is reasonable for packet headroom. This allows us to store
the rx_offset in a 8bit variable.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of testing if xdp_prog is present store the dma direction
in data path structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing around sets of rings and their parameters just
store all information in the data path structure.
We will no longer user xchg() on XDP programs when we swap programs
while the traffic is guaranteed not to be flowing. This allows us
to simply assign the entire data path structures instead of copying
field by field.
The optimization to reallocate only the rings on the side (RX/TX)
which has been changed is also removed since it seems like it's not
worth the code complexity.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use xdp_prog member of data path struct to carry the xdp_prog to
alloc/free free functions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use fl_bufsz member of data path struct to carry desired size of
free list entries.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of passing variables around use dp to store number of tx rings
for the stack and number of IRQ vectors.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make callers of nfp_net_ring_reconfig() pass newly allocated data
path structure. We will gradually make use of that structure
instead of passing parameters around to all the allocation functions.
This commit adds allocation and propagation of new data path struct,
no parameters are converted, yet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control BAR pointer is used to unmask interrupts so it should be
in the first cacheline of adapter structure.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all data path information into a separate structure. This way
we will be able to allocate new data path with all new rings etc.
and swap it in easily.
No functional changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the configuration of the AVB Credit-Based Shaper.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac debug dump for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares mac irq status treatment for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adapts flow_ctrl function to prepare it for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functionality of RX queue to dma channel mapping
based on configuration.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
