Since we are already using DMA attributes in igb for Rx there is no reason
why we can't also apply DMA_ATTR_WEAK_ORDERING which is needed on some
platforms to improve performance.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Information reported to ethtool about link modes is wrong for 25G NIC. Fix
it by checking for presence of 25G NIC, checking the link speed reported by
NIC firmware, and then assigning proper values to the
ethtool_link_ksettings struct.
Signed-off-by: Manish Awasthi <manish.awasthi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some short description of how callback's and NAPI interoperate.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the argument to channel callback from the channel pointer
to the internal data structure containing per-channel info.
This avoids any possible races when callback happens during
initialization and makes IRQ code simpler.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is being setup on boot, there is a small race where
network device callback is registered, but the netvsc_device pointer
is not set yet. This can cause a NULL ptr dereference if packet
arrives during this window.
Fixes: 46b4f7f5d1 ("netvsc: eliminate per-device outstanding send counter")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer array for the tx/rx sub crqs should be free'ed when
releasing the tx/rx sub crqs.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet netdev is connected to the controlling ldom's vswitch
for network bridging. However, for higher performance between ldoms,
there also is a channel between each client ldom. These connections are
represented in the sunvnet driver by a queue for each ldom. The driver
uses select_queue to tell the stack which queue to use by tracking the mac
addresses on the other end of each port. When a connected ldom shuts down,
the driver receives an LDC_EVENT_RESET and the port is removed from the
driver, thus a queue with no ldom on the other end will never be selected
for Tx.
The driver was trying to reinforce the "don't use this queue" notion with
netif_tx_stop_queue() and netif_tx_wake_queue(), which really should only
be used to signal a Tx queue is full (aka XOFF). This misuse of queue
state resulted in NETDEV WATCHDOG messages and lots of unnecessary calls
into the driver's tx_timeout handler. Simply removing these takes care
of the problem.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure multicast packets get counted in the device.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track our used and unused queue indexies correctly. Otherwise, as ports
dropped out and returned, they all eventually ended up with the same
queue index.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this driver, there is a "port" created for the connection to each of
the other ldoms; a netdev queue is mapped to each port, and they are
collected under a single netdev. The generic netdev statistics show
us all the traffic in and out of our network device, but don't show
individual queue/port stats. This patch breaks out the traffic counts
for the individual ports and gives us a little view into the state of
those connections.
Orabug: 25190537
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ldom VM is bound, the network vswitch infrastructure is set up for
it, but was being forced 'UP' by the userland switch configuration script.
When 'UP' but not actually connected to a running VM, the ipv6 neighbor
probes fail (not a horrible thing) and start cluttering up the kernel logs.
Funny thing: these are debug messages that never actually show up, but
we do see the net_ratelimited messages that say N callbacks were
suppressed.
This patch defers the netif_carrier_on() until an actual link has been
established with the VM, as indicated by receiving an LDC_EVENT_UP from
the underlying LDC protocol. Similarly, we take the link down when we
see the LDC_EVENT_RESET. Now when we see the ndo_open(), we reset the
link to get things talking again.
Orabug: 25525312
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the aquantia device mtu is changed the net_device structure is not
updated. As a result the ip command does not properly reflect the mtu change.
Commit 5513e16421 incorrectly assumed that __dev_set_mtu() was making the
assignment ndev->mtu = new_mtu; This is not true in the case where the driver
has a ndo_change_mtu routine.
Fixes: 5513e16421 ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Cc: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David Arcari <darcari@redhat.com>
Tested-by: Pavel Belous <pavel.belous@aquantia.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All IRQs owned by the PF and VF drivers share the same nondescript name
"octeon"; this makes it difficult to setup interrupt affinity.
Change the IRQ names to reflect their specific purpose:
LiquidIO<id>-<func>-<type>-<queue pair num>
Examples:
LiquidIO0-pf0-rxtx-3
LiquidIO1-vf1-rxtx-0
LiquidIO0-pf0-aux
We cannot use netdev->name for naming the IRQs because:
1. Early during init, the PF and VF drivers require interrupts to
send/receive control data from the NIC firmware; so the PF and VF
must request IRQs long before the netdev struct is registered.
2. The IRQ name can only be specified at the time it is requested.
It cannot be changed after that.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove invalid call to dma_sync_single_for_cpu() because previous DMA
allocation was coherent--not streaming. Remove code that references fields
in struct list_head; replace it with calls to list_empty() and
list_first_entry(). Also, add comment to clarify complicated if statement.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows the BCMA version of the bgmac driver to obtain MAC address
from the device tree. If no MAC address is specified there, then
the previous behavior (obtaining MAC address from SPROM) is
used.
Signed-off-by: Steve Lin <steven.lin1@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_8xx is being deprecated. Since the includes dependent on
CONFIG_8xx are useless, just drop them.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that port netdevs can be enslaved to a VRF master we need to make
sure the device's routing tables won't be flushed upon the insertion of
a l3mdev rule.
Note that we assume the notified l3mdev rule is a simple rule as used by
the VRF master. We don't check for the presence of other selectors such
as 'iif' and 'oif'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.
Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.
If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We usually destroy the netdev's router interface (RIF) when the last IP
address is removed from it.
However, we shouldn't do that if it's enslaved to an L3 master device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router interface (RIF) is created due to a netdev being enslaved
to a VRF master, then it should be associated with the appropriate
virtual router (VR) and not the default one.
If netdev is a VRF slave, lookup the VR based on the VRF's table ID.
Otherwise default to the MAIN table.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow listeners of the subsequent CHANGEUPPER notification to retrieve
the VRF's table ID by calling l3mdev_fib_table() with the slave netdev.
Without this change, the netdev won't be considered an L3 slave and the
function would return 0.
This is consistent with other master device such as bridge and bond that
set the slave's private flag before linking. It also makes
do_vrf_{add,del}_slave() symmetric.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit c3852ef7f2 ("ipv4: fib: Replay events when registering FIB
notifier") we dumped the FIB tables and replayed the events to the
passed notification block.
However, we merely sent a RULE_ADD notification in case custom rules
were in use. As explained in previous patches, this approach won't work
anymore. Instead, we should notify the caller about all the FIB rules
and let it act accordingly.
Upon registration to the FIB notification chain, replay a RULE_ADD
notification for each programmed FIB rule, custom or not. The integrity
of the dump is ensured by the mechanism introduced in the above
mentioned commit.
Prevent regressions by making sure current listeners correctly sanitize
the notified rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetch target operating channel during potential radar detection when
the interface is just brought up, but no channel is assigned from
userspace. In this scenario rx_channel may not be having a valid pointer
hence fetch the target operating channel to avoid warnings as below
which can be triggered by the commands with DFS testing over longer run
comamnds:
iw wlan1 set type mesh
ifconfig wlan1 up (valid tgt_oper_chan only)
iw wlan1 cac trigger freq 5260 HT20 (valid rx_channel, tgt_oper_chan)
iw wlan1 cac trigger freq 5280 HT20
iw wlan1 cac trigger freq 5300 HT20
Once the CAC expires, current channel context will be removed and
we are only left with the fallback option of using 'target operating
channel'
Firmware and driver log:
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath: phy1: DFS: radar found on freq=5260: id=5, pri=3151, count=6,
count_false=11
ath: phy1: DFS: radar found on freq=5280: id=1, pri=1351, count=6,
count_false=4
ath: phy1: DFS: radar found on freq=5300: id=1, pri=1125, count=5,
count_false=4
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
ath10k_pci 0001:01:00.0: failed to derive channel for radar pulse,
treating as radar
Call trace:
WARNING: CPU: 1 PID: 2145 at
backports-20161201-3.14.77-9ab3068/net/wireless/chan.c:265
cfg80211_set_dfs_state+0x3c/0x88 [cfg80211]()
Workqueue: phy1 ieee80211_dfs_radar_detected_work
[mac80211]
[<c0320770>] (warn_slowpath_null) from [<bf79b90c>]
(cfg80211_set_dfs_state+0x3c/0x88 [cfg80211])
[<bf79b90c>] (cfg80211_set_dfs_state [cfg80211]) from
[<bf79697c>] (cfg80211_radar_event+0xc4/0x140 [cfg80211])
[<bf79697c>] (cfg80211_radar_event [cfg80211]) from
[<bf83c058>] (ieee80211_dfs_radar_detected_work+0xa8/0xb4 [mac80211])
[<bf83c058>] (ieee80211_dfs_radar_detected_work
[mac80211]) from [<c0339518>] (process_one_work+0x298/0x4a4)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The check on ret for an error is redundant because it is already been
checked for non-zero earlier on and ret is never non-zero at this point.
Fix this by removing the redundant check and error message.
Detected by CoverityScan, CID#1357170 ("Logically Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Doing so enables the FFT generation without prior
configuration, leading to an IRQ storm caused by
invalid (or at least unwanted) PHY errors.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If a 5 GHz radio is calibrated for operation in both
the low band (channels 36 to 64) and high band(channels 100 to 169),
hardware allows operations in all the listed channels. However,
if the chip has been calibrated only for the low/high band and
a high/low band channel is configured, due to lack of calibration
there will be potentially invalid signal on those non calibrated channels.
To avoid this problem this patch sets IEEE80211_CHAN_DISABLED flag for
those non calibrated channels by using low_5ghz_chan and high_5ghz_chan
values which we get from target through wmi service ready event.
Driver initialized flags are getting re initialized in handle_channel
in cfg80211. So calling the function to disable the non supported channel
from reg_notifier().
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If DFS is not enabled in hostapd (ieee80211h=0) DFS channels shall
not be available for use even though the hardware may have the capability
to support DFS. With this configuration (DFS disabled in hostapd) trying to
bring up ath10k device in DFS channel for AP mode fails and trying to
simulate DFS in ath10k debugfs results in a warning in cfg80211 complaining
invalid channel and this should be avoided in the driver itself rather than
false propogating RADAR detection to mac80211/cfg80211. Fix this by
checking for the first vif 'is_started' state(should work for client mode
as well) as all the vifs shall be configured for the same channel
sys/kernel/debug/ieee80211/phy1/ath10k# echo 1 > dfs_simulate_radar
WARNING: at net/wireless/chan.c:265 cfg80211_radar_event+0x24/0x60
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
WARNING: at net/wireless/nl80211.c:2488 nl80211_get_mpath+0x13c/0x4cc
Workqueue: phy0 ieee80211_dfs_radar_detected_work [mac80211]
[<c022f2d4>] (warn_slowpath_null) from
[<bf72dab8>] (cfg80211_radar_event+0x24/0x60 [cfg80211])
[<bf72dab8>] (cfg80211_radar_event [cfg80211]) from
[<bf7813e0>] (ieee80211_dfs_radar_detected_work+0x94/0xa0 [mac80211])
[<bf7813e0>] (ieee80211_dfs_radar_detected_work [mac80211]) from
[<c0242320>] (process_one_work+0x20c/0x32c)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We manually init wakeup info, but we don't detach it on device removal.
This means that if we (for example) rmmod + modprobe the driver, the
device framework might return -EEXIST the second time, and we'll
complain in the logs:
[ 839.311881] mwifiex_pcie 0000:01:00.0: fail to init wakeup for mwifiex
AFAICT, there's no other negative effect.
But we can fix this by disabling wakeup on remove, similar to what a few
other drivers do (e.g., the power supply framework).
This code (and bug) has existed on SDIO for a while, but it got moved
around and enabled for PCIe with commit 853402a008 ("mwifiex: Enable
WoWLAN for both sdio and pcie").
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mwifiex_dbg() log handler utilizes the struct device in
adapter->dev. Without it, it decides not to print anything.
As of commit 2e02b58142 ("mwifiex: Allow mwifiex early access to device
structure"), we started assigning that pointer only after we finished
mwifiex_register() -- this effectively neuters any mwifiex_dbg() logging
done before this point.
Let's move the device assignment into mwifiex_register().
Fixes: 2e02b58142 ("mwifiex: Allow mwifiex early access to device structure")
Cc: Rajat Jain <rajatja@google.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Reported-and-tested-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements workaround for errata 10GE_8 and ENET_11:
"HW reports length error for valid 64 byte frames with len <46 bytes"
by recovering them from error.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements workaround for errata 10GE_1:
10Gb Ethernet port FIFO threshold default values are incorrect.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Rx checksum validation logic and
adds NETIF_F_RXCSUM flag.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the wrong logical OR operation by changing it to
bit-wise OR operation.
Fixes: 3bb502f830 ("drivers: net: xgene: fix statistics counters race condition")
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the hardware checksum settings by properly program
the classifier. Otherwise, packet may be received with checksum error
on X-Gene1 SoC.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes a typo in the argument to xgene_enet_wr_mdio_csr().
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer hardware does not provide a cumulative payload length when multiple
descriptors are needed to handle the data. Once the MTU increases beyond
the size that can be handled by a single descriptor, the SKB does not get
built properly by the driver.
The driver will now calculate the size of the data buffers used by the
hardware. The first buffer of the first descriptor is for packet headers
or packet headers and data when the headers can't be split. Subsequent
descriptors in a multi-descriptor chain will not use the first buffer. The
second buffer is used by all the descriptors in the chain for payload data.
Based on whether the driver is processing the first, intermediate, or last
descriptor it can calculate the buffer usage and build the SKB properly.
Tested and verified on both old and new hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspending the PHY would be putting it in a low power state where it
may no longer allow us to do Wake-on-LAN.
Fixes: cc013fb488 ("net: bcmgenet: correctly suspend and resume PHY device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the end of the timeout loop, retries will always be zero so
the check for zero is redundant so remove it. Also replace
printk with pr_err as recommended by checkpatch.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the main ISR for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch configures TSO for all available tx queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
