The current code enables up to the maximum MSIX vectors in the PCIE
config space without considering the max completion rings available.
An MSIX vector is only useful when it has an associated completion
ring, so it is better to cap it.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No offload is performed on the XDP_TX ring so we can use the short TX
BDs. This has the effect of doubling the size of the XDP TX ring so
that it now matches the size of the rx ring by default.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is necessary to disable autoneg before enabling PHY loopback,
otherwise link won't come up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac loopback self test operates in polling mode. To support that,
we need to add functions to open and close the NIC half way. The half
open mode allows the rings to operate without IRQ and NAPI. We
use the XDP transmit function to send the loopback packet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci shutdown method to put device in the proper WoL and power state.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to driver probe function to check if the device is WoL capable
and if Magic packet WoL filter is currently set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IEEE80211_CHAN_RADAR is set by cfg80211, passive scan must be
performed. In mwifiex,active scan is performed even though flag is
set from cfg80211. mwifiex_reg_apply_radar_flags() function added
in this patch correctly uses radar flag.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In mwifiex,IEs such as supported channels, supported operating classes
20/40 BSS COexistence are missing and also extra QOS capabilities IE
is added during TDLS discovery response, TDLS setup request and
TDLS setupresponse.
This patch adds require IEs and also removes extra IE.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
trivial fix to spelling mistakes in wl1271_warning error message, change
iligal to invalid and opperation to operation.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When resetting the device, we take a synchronous firmware-loading code
path, which borrows a lot from the asynchronous path used at probe time.
We don't catch errors correctly though, which means that in the PCIe
driver, we may try to dereference the 'adapter' struct after
mwifiex_fw_dpc() has freed it. See this (erronous) print in
mwifiex_pcie_reset_notify():
mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);
Let's instead refactor the synchronous (or "!req_fw_nowait") path so
that we propagate errors and handle them properly.
This fixes a use-after-free issue in the PCIe driver, as well as a
misleading debug message ("successful"). It looks like the SDIO driver
doesn't have these problems, since it doesn't do anything after
mwifiex_reinit_sw().
Fixes: 4c5dae59d2 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to reinit the FW when resetting the device (in the
synchronous version of mwifiex_init_hw_fw() -> mwifiex_fw_dpc()),
mwifiex_fw_dpc() will tear down the interface and free up the adapter.
But we don't actually check for all failure cases of mwifiex_fw_dpc(),
so some of them fall through and dereference adapter->fw_done with a
freed adapter, causing a use-after-free bug.
In any case, mwifiex_fw_dpc() will always signal FW completion -- in the
error OR success case -- so at best, this was repeat work. Let's not do
it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_pcie_suspend() we inform the firmware on the device that
it will enter in D3 state. Before this is done we already bring down
the bus state. However, When entering D3 fails we abort the suspend
and the bus state need to be restored.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.
Verified using two terminals:
Terminal 1 Terminal 2
-------------------------- ---------------------------------
# ip netns add brcm-wifi # iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x1
# ip netns exec brcm-wifi bash
# iw dev
# echo $$
20337 # iw phy0 set netns 20337
# iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x2
# iw phy0 interface add wl3.ap type __ap
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x3
Interface wlan3
ifindex 11
wdev 0x2
# iw dev
# iw phy0 set netns 1
# iw dev
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x5
Interface wlan3
ifindex 11
wdev 0x4
Note:
increasing wdev identifier above indicates issue in
cfg80211 which is addressed separately.
Tested-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chip goes into low power state when this feature is enabled.
This was already enabled for SDIO and PCIe interface based
chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB firmware added support for sending command response/event through
interrupt endpoint, to enhance RX throughput. Added corresponding changes
required to support this feature. This change takes care of backward
compatibility with older firmware.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For quite some time now brcmfmac supports 802.11ac chipsets and it's
not limited to embedded devices only. There are even standalone PCIe
cards based on BCM43602 or BCM4366.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.12. Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled
rtlwifi
* fix scheduling while atomic regression
brcmfmac
* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().
To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.
This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.
_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.
Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.
Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled
rtlwifi
* fix scheduling while atomic regression
brcmfmac
* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Holt HI-311x CAN controller. The HI311x
CAN controller is capable of transmitting and receiving standard data
frames, extended data frames and remote frames. The HI311x interfaces
with the host over SPI.
Datasheet: www.holtic.com/documents/371-hi-3110_v-rev-jpdf.do
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts TI HECC driver to DT only driver. This results in
removing ti_hecc.h containing now obsolete platform data.
Former transceiver_switch callback function will be now modelled via
regulator API.
Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As RoCE doesn't need to use the SRC, allocating ILT memory
on behalf of RoCE is wasting available ILT lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today there's no protocol supported that requires
support from the TM hardware block and enables SRIOV,
but we should still correct the calculation to reflect
the lines required for such future VFs instead of changing
the PF's own lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.
Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.
This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).
The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
