Fintek F81865 is a LPC to 6 UARTs SuperIO. It has less functional UARTs
likes F81866. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81865 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
Level/Low: IRQ_MODE0:0
Edge/High: IRQ_MODE0:1
The following list is brief descriptions of F81865:
F81865 (0704)
9Bit(not implements with mainline)
RS485(implemented)
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81866 is a LPC to 6 UARTs SuperIO. It has fully functional UARTs
likes F81216H. It's also need check the IRQ mode with system assigned,
but the configuration is not the same with F81216 series.
F81866 IRQ Mode setting:
0xf0
Bit1: IRQ_MODE0
Bit0: Share mode (always on)
0xf6
Bit3: IRQ_MODE1
Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
The following list is brief descriptions of F81866:
F81866 (1010)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek F81216 is a LPC to 4 UARTs device. It's the F81216 series but
support less functional than F81216AD/F81216H
The following list is brief descriptions of F81216 series:
F81216H (0105)
9Bit/High baud rate(not implements with mainline)
RS485, 128Bytes FIFO (implemented)
F81216AD (0216)
9Bit(not implements with mainline)
RS485(implemented)
F81216 (0208)
basically 16550A
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81216H had maximum 128Bytes FIFO, but some BIOS configurated
as normal 16Bytes FIFO. This patch will set 128Bytes FIFO and trigger
level multiplier as 4x when F81216H detected.
Default 16550A trigger level is 8Bytes. When this patch applied, the
trigger level will change to 8Byte x 4 = 32Byte. It can be reduce the RX
incoming interrupts.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set IRQ Mode when port probed in probe_setup_port()
It should hold the IO port premission via fintek_8250_enter_key() and
release via fintek_8250_exit_key() when we configure the SuperIO.
This patch will move all SuperIO configure operations to
probe_setup_port() to reduce fintek_8250_enter_key() and
fintek_8250_exit_key() usage.
Suggested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we need to access SuperIO registers, It should write register offset
to base_addr and read/write value to base_addr + 1 to perform read/write.
We can make it more simply with write/read functions.
This patch add sio_read_reg()/sio_write_reg()/sio_write_mask_reg() to
reduce SuperIO register operation with lot of outb()/inb().
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bugfix for the fintek driver required defining some macros, but
one of them clashes with a system header on ARM:
drivers/tty/serial/8250/8250_fintek.c:34:0: error: "IRQ_MODE" redefined [-Werror]
#define IRQ_MODE 0x70
In file included from /git/arm-soc/arch/arm/include/asm/ptrace.h:13:0,
from /git/arm-soc/arch/arm/include/asm/irqflags.h:6,
from /git/arm-soc/include/linux/irqflags.h:15,
from /git/arm-soc/arch/arm/include/asm/bitops.h:27,
from /git/arm-soc/include/linux/bitops.h:36,
from /git/arm-soc/include/linux/kernel.h:10,
from /git/arm-soc/include/linux/list.h:8,
from /git/arm-soc/include/linux/module.h:9,
from /git/arm-soc/drivers/tty/serial/8250/8250_fintek.c:11:
arch/arm/include/uapi/asm/ptrace.h:55:0: note: this is the location of the previous definition
This renames the newly introduced 'IRQ_MODE' macro to FINTEK_IRQ_MODE.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 4da22f1418 ("serial: 8250_fintek: fix the mismatched IRQ mode")
Link: https://patchwork.kernel.org/patch/9200119/
Acked-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Acked-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250_fintek driver advertises as the PNP0501 driver; however this
conflicts with the standard 16550A uart PNP0501. The conflict causes
the 8250_fintek driver to load with _every_ PNP0501, but never probe,
and causing the entire 8250 driver stack to unload if the 8250_fintek
driver is unloaded (modprobe doesn't know that 8250_pnp rather than
8250_fintek claimed the resource).
This patch merges the Fintek driver into 8250_base. On autoconfig_16550
the device is probed to verify if it is a FINTEK device or not.
This custom probing can be disabled completely via configuration. When a
Fintek device is not probed it will behave as a standard 16550A device,
with no RS485 capabilities.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fintek chip can be configured for io addresses different than the standard.
Query the chip for the configured addresses and try to match it with the
pnp address.
Reported-by: Peter Hong <peter_hong@fintek.com.tw>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch lets you set the RS485 cappabilites of the device through
TIOCSRS485 and TIOCGRS485 as defined on Documentation/serial/serial-rs485.txt
In order to probe the device, the PNP id and the device id is used.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
