Ensure the UART's transmitter is enabled when meson_console_putchar is
called. If not, then the console output is corrupt (the hardware seems
to try and send /something/ even if the TX is disabled).
This fixes corrupt console output on events such as trying to reboot the
system since the console tx may be called after drivers shutdown method has
been called.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Edward Cragg <edward.cragg@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_empty() uart_op should only return empty if both the transmit fifo
and the transmit state-machine are both idle. Add a test for the hardware's
XMIT_BUSY flag.
Note, this is possibly related to an issue where the port is being shutdown
with paritally transmitted characters in it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Edward Cragg <edward.cragg@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the uart startup entry is called, do not reset the port as this
could cause issues with anything left in the FIFO from a previous operation
such as a console write. Move the hardware reset to probe time and simply
clear the errors before enabling the port.
This fixes the issue where the console could become corrupted as there
where characters left in the output or output fifo when a user process
such as systemd would open/close the uart to transmit characters.
For example, you get:
[ 3.252263] systemd[1]: Dete
instead of:
[ 3.338801] systemd[1]: Detected architecture arm.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meson_uart_release_port() unmaps the register area but does not release
it. The meson_uart_request_port() calls devm_request_mem_region so the
release should call devm_release_mem_region() for that area so that anyt
subsequent use of these calls will work.
This fixes an issue where the addition of reset code before registering
the uart stops the console from working.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using relaxed IO accessors allows GCC to better optimise this code
as we eliminate the heavy memory barriers - for example, GCC can now
cache the address of a register across a read-modify-write sequence,
rather than reloading the base address, offset and access size flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add (incomplete) support for the ZTE UART to the AMBA PL011 driver.
This is similar to the ARM and ST variants, except it has a different
register address layout, and requires 32-bit accesses to the registers.
Use the newly introduced register tables and access size support to
cope with these differences.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for 32-bit register accesses to the AMBA PL011 UART. This
is needed for ZTE UARTs, which require 32-bit accesses as opposed to
the more normal 16-bit accesses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we can detect when the LCR register is split between TX and RX,
we don't need three entries in the table to deal with this. Reduce
this down to two entries by converting the REG_ST_LCRH_* entries to
standard REG_LCRH_* and remove REG_LCRH.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the ST variant register offset table to the driver. Currently,
this is an identical copy of the standard version, but this will be
modified in the following changes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the of-serial driver is now 8250 specific, we can move the
file to a more appropriate place in teh 8250 subdirectory and
adapt the Kconfig help text and file name.
I'm leaving the CONFIG_SERIAL_OF_PLATFORM symbol unchanged
to avoid breaking user configuration files unnecessarily.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only other user of this code was the nwp-serial driver, but that
is now gone, so we can remove a couple of #ifdef statments in this
driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bfin-uart code uses real time with struct timeval. This will
cause problems on 32-bit architectures in 2038 when time_t
overflows.
Since the code just needs delta value of time, it is not
necessary to record them in real time.
This patch changes the code to use the monotonic time instead,
replaces struct timeval and do_gettimeofday() with u64 and
ktime_get_ns().
Signed-off-by: DengChao <chao.deng@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If NO_DMA=y:
drivers/built-in.o: In function `atmel_release_rx_dma':
atmel_serial.c:(.text+0x2502e): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `atmel_release_tx_dma':
atmel_serial.c:(.text+0x25080): undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `atmel_tx_dma':
atmel_serial.c:(.text+0x2517a): undefined reference to `dma_sync_sg_for_cpu'
drivers/built-in.o: In function `atmel_release_tx_pdc':
atmel_serial.c:(.text+0x252e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_prepare_tx_pdc':
atmel_serial.c:(.text+0x2531a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `atmel_release_rx_pdc':
atmel_serial.c:(.text+0x25362): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_tx_pdc':
atmel_serial.c:(.text+0x25722): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_rx_from_pdc':
atmel_serial.c:(.text+0x2601a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_rx_from_dma':
atmel_serial.c:(.text+0x261b2): undefined reference to `dma_sync_sg_for_cpu'
atmel_serial.c:(.text+0x26264): undefined reference to `dma_sync_sg_for_cpu'
drivers/built-in.o: In function `atmel_prepare_rx_pdc':
atmel_serial.c:(.text+0x262de): undefined reference to `dma_unmap_single'
atmel_serial.c:(.text+0x26308): undefined reference to `dma_map_single'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found that our sc16is7xx on spi reported a TX fifo free space value
(TXLVL_REG) of 255 ocassionally, which is obviously wrong, with a
64 byte fifo and caused a buffer overrun and a kernel crash.
To trigger this, a large write to the tty is sufficient. The fifo fills,
TXLVL_REG reads zero, but the handle_tx function does a zero-data-length
write to the TX fifo anyways through sc16is7xx_fifo_write. The next
TXLVL_REG read then yields 255, for unknown reasons. A subsequent read
is ok.
Prevent zero-data-length writes if the TX fifo is full, because they are
pointless, and because they trigger wrong TXLVL read-outs.
Furthermore, prevent a TX buffer overrun if the peripheral reports values
larger than the buffer size and thus, don't allow the peripheral to crash
the kernel.
Signed-off-by: Florian Achleitner <achleitner.florian@fronius.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for REG_* register accessors. This change involves introducing
pl011_reg_to_offset() to convert REG_* to the hardware register offset,
and converting all call sites to use REG_* names. We need to fix up
locations where we check for equivalence of register offsets as well.
Much of this change was made via these sed expressions:
s/ST_UART01[1x]\(_[^_]*\|_LCRH_[TR]X\)\>/REG_ST\1/
s/UART01[1x]_\(DR\|RSR\|ECR\|FR\|ILPR\|[IF]BRD\|LCRH\|CR\|IFLS\|IMSC\|RIS\|MIS\|ICR\|DMACR\)\>/REG_\1/g
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add register accessor functions to amba-pl011. Much of this
transformation was done using the sed expression below, with any
left-overs fixed up manually afterwards, and code formatted to remain
within coding style.
s/readw(\(uap->port.membase\|regs\|port->membase\) +/pl011_read(\1,/g
s/writew(\(.*\) +/pl011_write(\1,/g
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are
supported for the 8250 console, but the 16-bit (MMIO16) is not.
The 8250 UART device on my board is connected to a 16-bit bus and
my main motivation is to use earlycon with it.
(Refer to arch/arm/boot/dts/uniphier-support-card.dtsi)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code waits until the transmitter becomes empty,
before sending each character, and after finishing the whole string.
This seems a bit redundant.
It can be more efficient by checking the transmitter only after sending
each character. This should be safe because the transmitter is already
empty at the first entry of serial_putc().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER has already been masked in early_serial8250_setup(), there is
no reason to save and restore it every time early_serial8250_write()
is called.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This UART driver should not depend on the console. They should be
orthogonal.
Surround the earlycon code with CONFIG_SERIAL_EARLYCON conditional
and rip off "depends on SERIAL_8250_CONSOLE".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reuses the code of drivers/tty/serial/8250/8250_early.c except
- Overwrite device->port.iotype and device->port.regshift for
UPIO_MEM32 because of_setup_earlycon() has set them for UPIO_MEM.
- Set device->baud to zero to prevent early8250_setup() from
initializing the divisor register because port->uartclk does not
match the frequency expected by this hardware.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/8250/Kconfig:config SERIAL_8250_MT6577
drivers/tty/serial/8250/Kconfig: bool "Mediatek serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_ATMEL
drivers/tty/serial/Kconfig: bool "AT91 / AT32 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that imx_mctrl_check is implemented below imx_get_mctrl the former
can call the latter directly instead of via sport->port.ops->get_mctrl.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .get_mctrl callback should not report the status of RTS or LOOP, so
drop this. Instead implement reporting the state of CAR (aka DCD) and
RI.
For .set_mctrl implement setting the DTR line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Even if the probability of this case is very low, fixing it made
static analyzers happy.
Solving this with of_device_get_match_data made also code simplier.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit replaces every instance of the string "jsm"
in the driver with JSM_DRIVER_NAME, as the two are
equivalent. This should increase overall consistency.
Signed-off-by: Gavin Thomas Claugus <gclaugus@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an earlycon console driver needs to acquire the uart_port.lock
spinlock for serial console output, and CONFIG_DEBUG_SPINLOCK=y:
BUG: spinlock bad magic on CPU#0, swapper/0
lock: sci_ports+0x0/0x3480, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
CPU: 0 PID: 0 Comm: swapper Not tainted 4.4.0-rc2-koelsch-g62ea5edf143bb1d0-dirty #2083
Hardware name: Generic R8A7791 (Flattened Device Tree)
[<c00173a0>] (unwind_backtrace) from [<c0013094>] (show_stack+0x10/0x14)
[<c0013094>] (show_stack) from [<c01f2338>] (dump_stack+0x70/0x8c)
[<c01f2338>] (dump_stack) from [<c00702d8>] (do_raw_spin_lock+0x20/0x190)
[<c00702d8>] (do_raw_spin_lock) from [<c0267590>] (serial_console_write+0x4c/0x130)
[<c0267590>] (serial_console_write) from [<c00734c4>] (call_console_drivers.constprop.13+0xc8/0xec)
[<c00734c4>] (call_console_drivers.constprop.13) from [<c0074ef0>] (console_unlock+0x354/0x440)
[<c0074ef0>] (console_unlock) from [<c0075bb4>] (register_console+0x2a0/0x394)
[<c0075bb4>] (register_console) from [<c06cb750>] (of_setup_earlycon+0x90/0xa4)
[<c06cb750>] (of_setup_earlycon) from [<c06cfb60>] (setup_of_earlycon+0x118/0x13c)
[<c06cfb60>] (setup_of_earlycon) from [<c06b34ac>] (do_early_param+0x64/0xb4)
[<c06b34ac>] (do_early_param) from [<c00472c0>] (parse_args+0x254/0x350)
[<c00472c0>] (parse_args) from [<c06b3860>] (parse_early_options+0x2c/0x3c)
[<c06b3860>] (parse_early_options) from [<c06b389c>] (parse_early_param+0x2c/0x40)
[<c06b389c>] (parse_early_param) from [<c06b5b08>] (setup_arch+0x520/0xaf0)
[<c06b5b08>] (setup_arch) from [<c06b3948>] (start_kernel+0x94/0x370)
[<c06b3948>] (start_kernel) from [<40008090>] (0x40008090)
Initialize the spinlock in of_setup_earlycon() and register_earlycon(),
to fix this for both DT-based and legacy earlycon. If the driver would
reinitialize the spinlock again, this is harmless, as it's allowed to
reinitialize an unlocked spinlock.
Alternatives are:
- Drivers having an early_serial_console_write() that only performs
the core functionality of serial_console_write(), without acquiring
the lock (which may be unsafe, depending on the hardware),
- Drivers initializing the spinlock in their private earlycon setup
functions.
As uart_port is owned by generic serial_core, and uart_port.lock is
initialized by uart_add_one_port() for the normal case, this can better
be handled in the earlycon core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reported-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
