Replace all code that initializes or releases fbdev emulation
throughout the driver. Instead initialize the fbdev client by a
single call to intel_fbdev_setup() after i915 has registered its
DRM device. Just like similar code in other drivers, i915 fbdev
emulation now acts like a regular DRM client. Do the same for xe.
The fbdev client setup consists of the initial preparation and the
hot-plugging of the display. The latter creates the fbdev device
and sets up the fbdev framebuffer. The setup performs display
hot-plugging once. If no display can be detected, DRM probe helpers
re-run the detection on each hotplug event.
A call to drm_client_dev_unregister() releases all in-kernel clients
automatically. No further action is required within i915. If the fbdev
framebuffer has been fully set up, struct fb_ops.fb_destroy implements
the release. For partially initialized emulation, the fbdev client
reverts the initial setup. Do the same for xe and remove its call to
intel_fbdev_fini().
v8:
- setup client in intel_display_driver_register (Jouni)
- mention xe in commit message
v7:
- update xe driver
- reword commit message
v6:
- use 'i915' for i915 device (Jouni)
- remove unnecessary code for non-atomic mode setting (Jouni, Ville)
- fix function name in commit message (Jouni)
v3:
- as before, silently ignore devices without displays
v2:
- let drm_client_register() handle initial hotplug
- fix driver name in error message (Jani)
- fix non-fbdev build (kernel test robot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409081029.17843-7-tzimmermann@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Move code from ad-hoc fbdev callbacks into DRM client functions
and remove the old callbacks. The functions instruct the client
to poll for changed output or restore the display.
The DRM core calls both, the old callbacks and the new client
helpers, from the same places. The new functions perform the same
operation as before, so there's no change in functionality.
Fox xe, remove xe_display_last_close(), which restored the fbdev
display. As with i915, the DRM core's drm_lastclose() performs
this operation automatically.
v8:
- mention xe in commit message
v7:
- update xe driver
v6:
- return errors from client callbacks (Jouni)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409081029.17843-6-tzimmermann@suse.de
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Let's simply convert all the current callers towards direct
xe_pm_runtime access and remove this extra layer of indirection.
No functional change is expected with this patch since
xe_mem_access_get was already using the xe_pm_runtime_get_noresume
at this point.
v2: Convert all the current callers instead of a big refactor
at once.
v3: - Rebased
- Squashed the GSC/HDCP
- Added a new case: sriov_pf_policy
- Improved commit message to highlight that
there's no functional change in this patch.
Reviewed-by: Matthew Auld <matthew.auld@intel.com> #v2
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240418143049.43231-1-rodrigo.vivi@intel.com
xe_pm_init is the very last thing during the xe_pci_probe(),
hence these protections are useless from the point of view
of ensuring that the device is awake.
Let's remove it so we continue towards the goal of killing
xe_device_mem_access.
v2: Adding more cases
v3: Provide a separate fix for xe_tile_init_noalloc return (Matt)
Adding a new case where display HDCP init calls which
are also called at display probe time.
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240417203952.25503-5-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The flags stored in the BO grew over time without following
much a naming pattern. First of all, get rid of the _BIT suffix that was
banned from everywhere else due to the guideline in
drivers/gpu/drm/i915/i915_reg.h that xe kind of follows:
Define bits using ``REG_BIT(N)``. Do **not** add ``_BIT`` suffix to the name.
Here the flags aren't for a register, but it's good practice to keep it
consistent.
Second divergence on names is the use or not of "CREATE". This is
because most of the flags are passed to xe_bo_create*() family of
functions, changing its behavior. However, since the flags are also
stored in the bo itself and checked elsewhere in the code, it seems
better to just omit the CREATE part.
With those 2 guidelines, all the flags are given the form
XE_BO_FLAG_<FLAG_NAME> with the following commands:
git grep -le "XE_BO_" -- drivers/gpu/drm/xe | xargs sed -i \
-e "s/XE_BO_\([_A-Z0-9]*\)_BIT/XE_BO_\1/g" \
-e 's/XE_BO_CREATE_/XE_BO_FLAG_/g'
git grep -le "XE_BO_" -- drivers/gpu/drm/xe | xargs sed -i -r \
-e 's/XE_BO_(DEFER_BACKING|SCANOUT|FIXED_PLACEMENT|PAGETABLE|NEEDS_CPU_ACCESS|NEEDS_UC|INTERNAL_TEST|INTERNAL_64K|GGTT_INVALIDATE)/XE_BO_FLAG_\1/g'
And then the defines in drivers/gpu/drm/xe/xe_bo.h are adjusted to
follow the coding style.
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240322142702.186529-3-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Enable HDCP for Xe by defining functions which take care of
interaction of HDCP as a client with the GSC CS interface.
Add intel_hdcp_gsc_message to Makefile and add corresponding
changes to xe_hdcp_gsc.c to make it build.
--v2
-add kfree at appropriate place [Daniele]
-remove useless define [Daniele]
-move host session logic to xe_gsc_submit.c [Daniele]
-call xe_gsc_check_and_update_pending directly in an if condition
[Daniele]
-use xe_device instead of drm_i915_private [Daniele]
--v3
-use xe prefix for newly exposed function [Daniele]
-remove client specific defines from intel_gsc_mtl_header [Daniele]
-add missing kfree() [Daniele]
-have NULL check for hdcp_message in finish function [Daniele]
-dont have too many variable declarations in the same line [Daniele]
--v4
-don't point the hdcp_message structure in xe_device to anything
until it properly gets initialized [Daniele]
--v5
-Squash commits for buildability
--v6
-Order includes alphabetically [Lucas]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240306024247.1857881-6-suraj.kandpal@intel.com
Bring changes from drm-misc-next that got merged in drm-next back to
drm-xe so they can be used for additional features.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
On MTL the GOP (for whatever reason) likes to bind its framebuffer
high up in the ggtt address space. This can conflict with whatever
ggtt_reserve_guc_top() is trying to do, and the result is that
ggtt_reserve_guc_top() fails and then we proceed to explode when
trying to tear down the driver. Thus far I haven't analyzed what
causes the actual fireworks, but it's not super important as even
if it didn't explode we'd still fail the driver load and the user
would be left with an unusable GPU.
To remedy this (without having to figure out exactly what
ggtt_reserve_guc_top() is trying to achieve) we can attempt to
relocate the BIOS framebuffer to a lower ggtt address. We can do
this at this early point in driver init because nothing else is
supposed to be clobbering the ggtt yet. So we simply change where
in the ggtt we pin the vma, the original PTEs will be left as is,
and the new PTEs will get written with the same dma addresses.
The plane will keep on scanning out from the original PTEs until
we are done with the whole process, and at that point we rewrite
the plane's surface address register to point at the new ggtt
address.
Since we don't need a specific ggtt address for the plane
(apart from needing it to land in the mappable region for
normal stolen objects) we'll just try to pin it without a fixed
offset first. It should end up at the lowest available address
(which really should be 0 at this point in the driver init).
If that fails we'll fall back to just pinning it exactly to the
origianal address.
To make sure we don't accidentlally pin it partially over the
original ggtt range (as that would corrupt the original PTEs)
we reserve the original range temporarily during this process.
v2: Try to pin explicitly to ggtt offset 0 as otherwise DG2 puts it
even higher (atm we have no PIN_LOW flag to force it low)
v3: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-16-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Currently we assume that we bind the BIOS fb exactly into the same
ggtt address where the BIOS left it. That is about to change, and
in order to keep intel_reuse_initial_plane_obj() working as intended
we need to compare the original ggtt offset (called 'base' here)
as opposed to the actual vma ggtt offset we selected. Otherwise
the first plane could change the ggtt offset, and then subsequent
planes would no longer notice that they are in fact using the same
ggtt offset that the first plane was already using. Thus the reuse
check will fail and we proceed to turn off these subsequent planes.
TODO: would probably make more sense to do the pure readout first
for all the planes, then check for fb reuse, and only then proceed
to pin the object into the final location in the ggtt...
v2: "fix" xe
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Tested-by: Paz Zcharya <pazz@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202224340.30647-15-ville.syrjala@linux.intel.com
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
intel_power_domains_init is called twice in xe_device_probe:
1) intel_power_domains_init()
xe_display_init_nommio()
xe_device_probe()
2) intel_power_domains_init()
intel_display_driver_probe_noirq()
xe_display_init_noirq()
xe_device_probe()
It needs remove one to avoid power_domains->power_wells double malloc.
unreferenced object 0xffff88811150ee00 (size 512):
comm "systemd-udevd", pid 506, jiffies 4294674198 (age 3605.560s)
hex dump (first 32 bytes):
10 b4 9d a0 ff ff ff ff ff ff ff ff ff ff ff ff ................
ff ff ff ff ff ff ff ff 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff8134b901>] __kmem_cache_alloc_node+0x1c1/0x2b0
[<ffffffff812c98b2>] __kmalloc+0x52/0x150
[<ffffffffa08b0033>] __set_power_wells+0xc3/0x360 [xe]
[<ffffffffa08562fc>] xe_display_init_nommio+0x4c/0x70 [xe]
[<ffffffffa07f0d1c>] xe_device_probe+0x3c/0x5a0 [xe]
[<ffffffffa082e48f>] xe_pci_probe+0x33f/0x5a0 [xe]
[<ffffffff817f2187>] local_pci_probe+0x47/0xa0
[<ffffffff817f3db3>] pci_device_probe+0xc3/0x1f0
[<ffffffff8192f2a2>] really_probe+0x1a2/0x410
[<ffffffff8192f598>] __driver_probe_device+0x78/0x160
[<ffffffff8192f6ae>] driver_probe_device+0x1e/0x90
[<ffffffff8192f92a>] __driver_attach+0xda/0x1d0
[<ffffffff8192c95c>] bus_for_each_dev+0x7c/0xd0
[<ffffffff8192e159>] bus_add_driver+0x119/0x220
[<ffffffff81930d00>] driver_register+0x60/0x120
[<ffffffffa05e50a0>] 0xffffffffa05e50a0
The call to intel_power_domains_cleanup() needs to stay where it is for
now. The main issue is that while the init is called by the display
side, shared by i915 and xe, the cleanup is called by a non-shared code
path. Fixing that will be done as a separate commit.
Fixes: 44e694958b ("drm/xe/display: Implement display support")
Signed-off-by: Xiaoming Wang <xiaoming.wang@intel.com>
[ reword commit message and explain why the fini needs to stay
where it is ]
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240202215658.561298-1-lucas.demarchi@intel.com
When CONFIG_DRM_I915_DEBUG is not set, a dummy
__i915_inject_probe_error() is provided on the xe side. Use the same
logic as in drivers/gpu/drm/i915/i915_utils.c to ifdef it out. This
fixes the build with W=1 and without that config:
CC [M] drivers/gpu/drm/xe/display/ext/i915_utils.o
../drivers/gpu/drm/xe/display/ext/i915_utils.c:19:5: error: no previous prototype for ‘__i915_inject_probe_error’ [-Werror=missing-prototypes]
19 | int __i915_inject_probe_error(struct drm_i915_private *i915, int err,
| ^~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Xe need to use remapped display page table for tiled framebuffers
on anywhere else than DG2. Here add function to write such dpt and
enable usage of remapped display page tables where needed.
Signed-off-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Define intel_hdcp_gsc_check_status in Xe to account
for changes in i915 and Xe.
intel_hdcp_check_status always returns false as gsc cs
interface is not yet ported.
intel_hdcp_gsc_cs_required always returns true as going
forward gsc cs will always be required by upcoming
platforms
--v5
-Define intel_hdcp_gsc_cs_required()
--v6
-Explain reasons for the return values [Chaitanya]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This introduces an exclusive version of vga decode for xe.
Rest of the display changes will be re-used from i915.
Currently it adds just a dummy implementation. VGA decode
needs to be handled correctly in i915, proper implementation
will be adopted once the i915 changes are finalized and merged
in upstream.
v2: Addressed Arun's review comments
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Arun R Murthy <arun.r.mruthy@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
As for display, the intent is to share the display code with the i915
driver so that there is maximum reuse there.
We do this by recompiling i915/display code twice.
Now that i915 has been adapted to support the Xe build, we can add
the xe/display support.
This initial work is a collaboration of many people and unfortunately
this squashed patch won't fully honor the proper credits.
But let's try to add a few from the squashed patches:
Co-developed-by: Matthew Brost <matthew.brost@intel.com>
Co-developed-by: Jani Nikula <jani.nikula@intel.com>
Co-developed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Co-developed-by: Matt Roper <matthew.d.roper@intel.com>
Co-developed-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Co-developed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Co-developed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
