There are cases where an OTG is remapped from driving a regular HDMI
display to a DP/eDP display. There are also cases where DTBCLK needs to
be enabled for HPO, but DTBCLK DTO programming may be done while OTG is
still enabled which is dangerous as the PIPE_DTO_SRC_SEL programming may
change the pixel clock generator source for a mapped and running OTG and
cause it to hang.
Remove the PIPE_DTO_SRC_SEL programming from this sequence since it is
already done in program_pixel_clk(). Additionally, make sure that
program_pixel_clk sets DTBCLK DTO as source for special HDMI cases.
Cc: stable@vger.kernel.org # 6.11+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DTBCLK_P is used to generate virtual pixel clock, and to drive the HPO
stream encoder clock. Programming the required clock when
enabling/disabling both components can cause issues.
For example, if HPO is being disabled and clock source is changed to
REFCLK, virtual pixel rate will then be wrong, causing issues in CRTC.
[HOW]
Only program the DTBCLK_P when programming CRTC, as its expected it will
be enabled prior to HPO, and disabled after HPO in all valid cases.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If two monitors with TMDS signals were timing synced and one was
disconnected, the stream would go out of sync too early due to
the PLL turning off and the system could hang
[How]
On link disable output, change PHY FSM transition from TX_EN-to-PHY_OFF
to TX_EN-to-PLL_ON for TMDS
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Ryan Seto <ryanseto@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable dpp rcg before we disable dppclk in hw_init cause system
hang/reboot
[How]
we remove dccg rcg related code from init into a separate function and
call it after we init pipe
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Qili Lu <qili.lu@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Function used to check the number of FEs connected to the current BE.
This was then used to determine if the symclk could be disabled, if
all FEs were disconnected. However, the function would skip over the
primary FE and return 0 when the primary FE was still connected. This
caused black screens on driver disable with an MST daisy chain hooked
up.
[How]
Refactor the function to correctly return the number of FEs connected
to the input BE. Also, rename it for clarity.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Function was used to check the number of FEs connected to the current BE.
This was then used to determine if the symclk could be disabled, if all
FEs were disconnected. However, the function would skip over the primary
FE and return 0 when the primary FE was still connected. This caused black
screens on driver disable with an MST daisy chain hooked up.
[HOW]
Refactored the function to correctly return the number of FEs connected to
the input BE. Also renamed it for clarity.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
fe_clk_en and be_clk_sel have size of 4 but sizeof(fe_clk_en) has
byte size 16 which is lager than the array size.
[HOW]
Use ARRAY_SIZE for calculating size.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reference clock, either DPREFCLK or DTBCLK can be a value of 0
which then will encounter division by 0.
[How]
Avoid further calculation and programming if refclk is not
populated.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
fe_clk_en has size of 5 but sizeof(fe_clk_en) has byte size 20 which is
lager than the array size.
[HOW]
Divide byte size 20 by its element size.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
