The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain, so fix the binding example accordingly.
In relation with fix c5a2838025 ("ARM: dts: at91: Configure I2C SCL
gpio as open drain").
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Fixes: 19e5cef058 ("dt-bindings: i2c: at91: document optional bus recovery properties")
The at91 I2C controller can support bus recovery by re-assigning SCL
and SDA to gpios. Add the optional pinctrl and gpio properties to do
so.
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
[codrin.ciubotariu@microchip.com: rebased]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
SAM9X60 also supports i2c-sda-hold-time-ns. Fix the documentation accordingly.
Fixes: 2034e3f4c9 ("dt-bindings: i2c: at91: add new compatible")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The "at," prefix was never correct for Atmel, so fix the few occurrences
that got it wrong. Use "atmel," instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Peter Rosin <peda@axentia.se>
[wsa: merged two patches into one, dropped 'trivial-devices' hunk which
needs to go in seperately]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
add a new value "atmel,sama5d2-i2c" for the "compatible" property.
add a new optional property "atmel,fifo-size" to enable FIFO support when
available.
add missing optional properties "dmas" and "dma-names".
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds the ability to set "clock-frequency" in the device tree for the at91
i2cbus following the naming of other i2c bus implementations. If the property
is not set,the clock frequency will default to the previously used define
of 100KHz.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Filenames of devictree binding documentation seems to be arbitrary and
for me it is unneeded hazzle to find the corresponding documentation for
a specific driver.
Naming the description the same as the driver is a lot easier and makes
sense to me since the driver defines the binding it understands.
Also, remove a reference in one source to the binding documentation, since path
information easily gets stale.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Cc: Rob Herring <robherring2@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
