LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
In order to pass AVI infoframes to LSPCON devices, a source has to
write them in a vendor recommended method and location.
This patch series:
- adds generic LSPCON infoframe setup functions.
- registers these functions into existing AVI infoframe framework.
- triggers these functions from modeset sequence.
Next patches in the series will add vendor specific code.
V2: Added new parameter to align with new definition of
drm_hdmi_avi_infoframe_quant_range
V3: Added r-b from Maarten (for V2)
Added new parameter output_format in struct lspcon to accommodate
Ville's review comments on last patch of the series
V4: Addressed Ville's review comment
- Do not add output_format in LSPCON state, as its non-atomic. Add
this into CRTC state (added in a later patch).
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase
V11: Accommodated rebasing changes in intel_git_port fptrs (set_infoframes and infoframe_enabled)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-5-git-send-email-shashank.sharma@intel.com
This patch adds support for YCBCR 4:4:4 CRTC output format.
To do this, this patch extends the existing YCBCR 4:2:0
framework by:
- Adding new parameter in for YCBCR 4:4:4 enum crtc_iutput_format.
- Adding case for YCBCR 4:4:4 in while setting AVI infoframes.
- Adding necessary checks in modeset sequence.
V3: Added this patch in the series
V4: Added r-b from Maarten (for v3)
Addressed review comment from Ville:
Do not use (config->output_format > CRTC_OUTPUT_RGB)
V5: Rebase
V6: Rebase and small change, to accommodate changes in patch 2
V7: Fixed checkpatch alignment warnings
V8: Rebase
V9: Rebase
V10: Rebase
V11: Addressed review comment from Ville
Missing output_format_str[INTEL_OUTPUT_FORMAT_YCBCR444]
Added Ville's R-B.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-3-git-send-email-shashank.sharma@intel.com
Currently, we are using a bool in CRTC state (state->ycbcr420),
to indicate modeset, that the output format is YCBCR 4:2:0. Now in
order to support other YCBCR formats, we will need more such flags.
This patch adds a new enum parameter for YCBCR 4:2:0 outputs, in the
CRTC output formats and then plugs it during the modeset.
V3: Added this patch in the series, to address review comments from
second patchset.
V4: Added r-b from Maarten (on v3)
Addressed review comments from Ville:
- Change the enum name to intel_output_format.
- Start the enum value (INVALID) from 0 instaed of 1.
- Set the crtc's output_format to RGB in encoder's compute_config.
V5: Broke previous patch 1 into two parts,
- first patch to add CRTC output format in general
- second patch (this one) to add YCBCR 4:2:0 output
format specifically.
- Use ARRAY_SIZE(format_str) for output format validity check (Ville)
V6: Added a separate function to calculate crtc_state->output_format, and
calling it from various get_config function (Fix CI build warning)
V7: Fixed checkpatch warnings for alignment
V8: Rebase
V9: Rebase
V10: Rebase
V11: Addressed review comments from Ville:
- Change check for CRTC output format from > ARRAY_SIZE to >= ARRAY_SIZE.
- Check for values < INTEL_OUTPUT_FORMAT_RGB is unnecessary.
- No need to get CRTC YCBCR config, for pre-BDW functions.
Added Ville's r-b.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-2-git-send-email-shashank.sharma@intel.com
This patch adds an enum "intel_output_format" to represent
the output format of a particular CRTC. This enum will be
used to produce a RGB/YCBCR4:4:4/YCBCR4:2:0 output format
during the atomic modeset calculations.
V5:
- Created this separate patch to introduce and init output_format.
- Initialize parameters of output_format_str respectively (Jani N).
- Call it intel_output_format than crtc_output_format(Ville).
- Set output format in pipe_config for every encoder (Ville).
- Get rid of extra DRM_DEBUG_KMS during get_pipe_config (Ville)
V6: Rebase
V7: Fixed alignment warnings (checkpatch)
V8: Another check[atch warning for alignment
V9: Rebase
V10: Rebase on top of DSI restructure
V11: Addressed review comment from Ville
- Set CRTC format for pre-HSW get_pipe_config() function too.
Added Ville's R-B
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-1-git-send-email-shashank.sharma@intel.com
There's not much point in following the primary vs. sprite split
for the SKL+ universal plane init code. The only difference is
of our own doing in the form of the .check_plane(). Let's make
a small exception for that little detail and otherwise share
the same code to initialize all the universal planes.
Eventually we should eliminate the mess around .check_plane()
as well, but for now let's be happy with some code reduction.
v2: Remember to set up plane->has_fbc
Make skl_plane_has_ccs() static
v3: Rebase due to NV12, rename some variables
v4: Don't leave the color_encoding/range props behind
v5: Rebase dur to blend properties, skl_plane_max_stride() and
skl_plane_check()
v6: Make skl_update_plane() static
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-10-ville.syrjala@linux.intel.com
commit 4e0b83a567 ("drm/i915: Extract per-platform plane->check()
functions") removed the plane max stride check for sprite planes.
I was going to add it back when introducing GTT remapping for the
display, but after further thought it seems better to re-introduce
it separately.
So let's add the max stride check back. And let's do it in a nicer
form than what we had before and do it for all plane types (easy
now that we have the ->max_stride() plane vfunc).
Only sprite planes really need this for now since primary planes
are capable of scanning out the current max fb size we allow, and
cursors have more stringent stride checks elsewhere.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 4e0b83a567 ("drm/i915: Extract per-platform plane->check() functions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918140243.12207-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
drm_atomic_helper_commit_planes_on_crtc calls begin_commit,
then plane_update hooks, then flush_commit. Because we keep our own
visibility tracking through plane_state->visible there's no need to
rely on the atomic hooks for this.
By explicitly writing our own helper, we can update visible planes
as needed, which is useful to make NV12 support work as intended.
Changes since v1:
- Reword commit message. (Matt Roper)
- Rename to intel_update_planes_on_crtc(). (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-6-maarten.lankhorst@linux.intel.com
Split up intel_check_primary_plane() and intel_check_sprite_plane()
into per-platform variants. This way we can get a unified behaviour
between the SKL universal planes, and we stop checking for non-SKL
specific scaling limits for the "sprite" planes. And we now get
a natural place where to add more plarform specific checks.
v2: Split the .check_plane() calling convention change out (José)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907152413.15761-10-ville.syrjala@linux.intel.com
Let's store the final plane stride in the plane state. This avoids
having to pick between the normal vs. rotated stride during hardware
programming. And once we get GTT remapping the plane stride will
no longer match the fb stride so we'll need a place to store it
anyway.
v2: Keep checking fb->pitches[0] for cursor as later on we won't
populate plane_state->color_plane[0].stride for invisible planes
and we have been checking the cursor fb stride even for invisible
planes
v3: s/betwen/between in commit msg (José)
v4: Check color_plane[0].stride instead of fb->pitches[0] in
the skl_check_main_surface() X-tiling kludge
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180911150139.23922-1-ville.syrjala@linux.intel.com
Merge tag 'gvt-next-2018-09-04'
drm-intel-next-2018-09-06-1:
UAPI Changes:
- GGTT coherency GETPARAM: GGTT has turned out to be non-coherent for some
platforms, which we've failed to communicate to userspace so far. SNA was
modified to do extra flushing on non-coherent GGTT access, while Mesa will
mitigate by always requiring WC mapping (which is non-coherent anyway).
- Neuter Resource Streamer uAPI: There never really were users for the feature,
so neuter it while keeping the interface bits for compatibility. This is a
long due item from past.
Cross-subsystem Changes:
- Backmerge of branch drm-next-4.19 for DP_DPCD_REV_14 changes
Core Changes:
- None
Driver Changes:
- A load of Icelake (ICL) enabling patches (Paulo, Manasi)
- Enabled full PPGTT for IVB,VLV and HSW (Chris)
- Bugzilla #107113: Distribute DDB based on display resolutions (Mahesh)
- Bugzillas #100023,#107476,#94921: Support limited range DP displays (Jani)
- Bugzilla #107503: Increase LSPCON timeout (Fredrik)
- Avoid boosting GPU due to an occasional stall in interactive workloads (Chris)
- Apply GGTT coherency W/A only for affected systems instead of all (Chris)
- Fix for infinite link training loop for faulty USB-C MST hubs (Nathan)
- Keep KMS functional on Gen4 and earlier when GPU is wedged (Chris)
- Stop holding ppGTT reference from closed VMAs (Chris)
- Clear error registers after error capture (Lionel)
- Various Icelake fixes (Anusha, Jyoti, Ville, Tvrtko)
- Add missing Coffeelake (CFL) PCI IDs (Rodrigo)
- Flush execlists tasklet directly from reset-finish (Chris)
- Fix LPE audio runtime PM (Chris)
- Fix detection of out of range surface positions (GLK/CNL) (Ville)
- Remove wait-for-idle for PSR2 (Dhinakaran)
- Power down existing display hardware resources when display is disabled (Chris)
- Don't allow runtime power management if RC6 doesn't exist (Chris)
- Add debugging checks for runtime power management paths (Imre)
- Increase symmetry in display power init/fini paths (Imre)
- Isolate GVT specific macros from i915_reg.h (Lucas)
- Increase symmetry in power management enable/disable paths (Chris)
- Increase IP disable timeout to 100 ms to avoid DRM_ERROR (Imre)
- Fix memory leak from HDMI HDCP write function (Brian, Rodrigo)
- Reject Y/Yf tiling on interlaced modes (Ville)
- Use a cached mapping for the physical HWS on older gens (Chris)
- Force slow path of writing relocations to buffer if unable to write to userspace (Chris)
- Do a full device reset after being wedged (Chris)
- Keep forcewake counts over reset (in case of debugfs user) (Imre, Chris)
- Avoid false-positive errors from power wells during init (Imre)
- Reset engines forcibly in exchange of declaring whole device wedged (Mika)
- Reduce context HW ID lifetime in preparation for Icelake (Chris)
- Attempt to recover from module load failures (Chris)
- Keep select interrupts over a reset to avoid missing/losing them (Chris)
- GuC submission backend improvements (Jakub)
- Terminate context images with BB_END (Chris, Lionel)
- Make GCC evaluate GGTT view struct size assertions again (Ville)
- Add selftest to exercise suspend/hibernate code-paths for GEM (Chris)
- Use a full emulation of a user ppgtt context in selftests (Chris)
- Exercise resetting in the middle of a wait-on-fence in selftests (Chris)
- Fix coherency issues on selftests for Baytrail (Chris)
- Various other GEM fixes / self-test updates (Chris, Matt)
- GuC doorbell self-tests (Daniele)
- PSR mode control through debugfs for IGTs (Maarten)
- Degrade expected WM latency errors to DRM_DEBUG_KMS (Chris)
- Cope with errors better in MST link training (Dhinakaran)
- Fix WARN on KBL external displays (Azhar)
- Power well code cleanups (Imre)
- Fixes to PSR debugging (Dhinakaran)
- Make forcewake errors louder for easier catching in CI (WARNs) (Chris)
- Fortify tiling code against programmer errors (Chris)
- Bunch of fixes for CI exposed corner cases (multiple authors, mostly Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907105446.GA22860@jlahtine-desk.ger.corp.intel.com
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
After
commit 2cd9a689e9 ("drm/i915: Refactor intel_display_set_init_power() logic")
it makes more sense to check the power domain/well refcounts after
enabling the power domains functionality. Before that it's guaranteed
that most power wells (in the INIT domain) will have a reference held,
so not an interesting state.
While at it also add the check after the init_hw/fini_hw, disable and
suspend/resume steps. Make the test optional on a Kconfig option since
it may add substantial overhead: on VLV/CHV the corresponding PUNIT reg
access for each power well may take up to 20ms.
v2:
- Add the state check to more spots. (Chris)
v3:
- During suspend check the state before deiniting display core.
Afterwards DC states are disabled (and so the dc_off power well is
enabled) even though we don't hold a reference on it.
- Do the test conditionally based on a new Kconfig option. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Add DRM_I915_DEBUG_RUNTIME_PM to welcome messages]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817145837.26592-1-imre.deak@intel.com
The device global init_power_on flag is somewhat arbitrary and makes
debugging power refcounting problems difficult. Instead arrange things
so that all display power domain get has a corresponding put call. After
this change we have the following sequences:
driver loading:
intel_power_domains_init_hw();
<other init steps>
intel_power_domains_enable();
driver unloading:
intel_power_domains_disable();
<other uninit steps>
intel_power_domains_fini_hw();
system suspend:
intel_power_domains_disable();
<other suspend steps>
intel_power_domains_suspend();
system resume:
intel_power_domains_resume();
<other resume steps>
intel_power_domains_enable();
at other times while the driver is loaded:
intel_display_power_get();
...
intel_display_power_put();
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-2-imre.deak@intel.com
Currently, we cancel the extra wakeref we have for !runtime-pm devices
inside power_wells_fini_hw. However, this is not strictly paired with
the acquisition of that wakeref in runtime_pm_enable (as the fini_hw may
be called on errors paths before we even call runtime_pm_enable). Make
the symmetry more explicit and include a check that we do release all of
our rpm wakerefs.
v2: Fixup transfer of ownership back to core whilst keeping our wakeref
count balanced.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-1-imre.deak@intel.com
Currently tests modify i915.enable_psr and then do a modeset cycle
to change PSR. We can write a value to i915_edp_psr_debug to force
a certain PSR mode without a modeset.
To retain compatibility with older userspace, we also still allow
the override through the module parameter, and add some tracking
to check whether a debugfs mode is specified.
Changes since v1:
- Rename dev_priv->psr.enabled to .dp, and .hw_configured to .enabled.
- Fix i915_psr_debugfs_mode to match the writes to debugfs.
- Rename __i915_edp_psr_write to intel_psr_set_debugfs_mode, simplify
it and move it to intel_psr.c. This keeps all internals in intel_psr.c
- Perform an interruptible wait for hw completion outside of the psr
lock, instead of being forced to trywait and return -EBUSY.
Changes since v2:
- Rebase on top of intel_psr changes.
Changes since v3:
- Assign psr.dp during init. (dhnkrn)
- Add prepared bool, which should be used instead of relying on psr.dp. (dhnkrn)
- Fix -EDEADLK handling in debugfs. (dhnkrn)
- Clean up waiting for idle in intel_psr_set_debugfs_mode.
- Print PSR mode when trying to enable PSR. (dhnkrn)
- Move changing psr debug setting to i915_edp_psr_debug_set. (dhnkrn)
Changes since v4:
- Return error in _set() function.
- Change flag values to make them easier to remember. (dhnkrn)
- Only assign psr.dp once. (dhnkrn)
- Only set crtc_state->has_psr on the crtc with psr.dp.
- Fix typo. (dhnkrn)
Changes since v5:
- Only wait for PSR idle on the PSR connector correctly. (dhnkrn)
- Reinstate WARN_ON(drrs.dp) in intel_psr_enable. (dhnkrn)
- Remove stray comment. (dhnkrn)
- Be silent in intel_psr_compute_config on wrong connector. (dhnkrn)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809142101.26155-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
It makes sense to keep unchanging data const. Extract such fields from
the i915_power_well struct into a new i915_power_well_desc struct that
we initialize during compile time. For the rest of the dynamic
fields allocate an array of i915_power_well objects in i915 dev_priv,
and link to each of these objects their corresponding
i915_power_well_desc object.
v2:
- Fix checkpatch warnings about missing param name in fn declaration and
lines over 80 chars. (Paulo)
- Move check for unique IDs to __set_power_wells().
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Fixed checkpatch warn in __set_power_wells()]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-5-imre.deak@intel.com
