When plane size changes, we need to reprogram surface pitch in addition
to viewport and scaler. This change is a conservative way to make this happen.
However it could be more optimized to move pitch programming into
mem_program_viewport.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Andrew Jiang <Andrew.Jiang@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It may take over 200ms for wait hpd ready. To optimize the resume time,
we can power on eDP in init_hw, wait for hpd ready when doing link
training.
also create separate eDP enable function to make sure eDP is powered up
before doing and DPCD access, as HPD low will result in DPDC transaction
failure.
After optimization,
setpowerstate 145ms -> 9.8ms,
DPMS 387ms -> 18.9ms
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cursor is abnormal after pipe_ctx is changed in context.
Cause: cursor attributes is programmed right after front end
programming, but it use old pipe_ctx to program which is not
updated yet.
Solution:
Program cursor regs after context swapped.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During HW initialization, instead of assuming or
detecting the existing MPCC mux configuration and
then removing existing planes, reset all the MPCC
muxes.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HDR display playing video underflow is observed when switching
to full screen due to program a lower watermark right after unlock otg.
Instead of disable plane in next flip coming, if there is a
plane disconnected, after otg unlock wait for mpcc idle and disable
the plane, then program watermark. So there is enough warter mark to make
sure current frame data pass through.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Work around for a hw bug causing optc underflow if blank data
double buffer disable and remove mpcc.
Checking optc status after otg unlock, after wait mpcc idle
check status again, if optc underflow just happens after wait
mpcc idle, clear underflow status and enable blank data double
buffer.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rather than setting it every time there's a full update with surface
count > 0, set it when we need to do plane_atomic_disconnect. Also make
sure that we unset the flag in plane_atomic_disable, so that in the
event we run through a sequence where we do disconnect followed by an
immediate disable, we do not do unnecessarily request a passive flip to
do the optimization.
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix update_mpcc logic to only call assert_mpcc_idle_before_connect
if mpcc is not already being used (and required removal).
Update set_out_rate_control to include optional flow control parameter.
In init_mpcc_from_hw check for case where bot_sel is same as mpcc_id.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Integrating MPC pseudocode to support new blending cases
with secondary MPCC list.
This includes a design change to MPC data structures and
interfaces.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On S3 resume, we do not reconstruct OPP, but we do need to
reinitialize some of its values to the default ones.
Therefore, move those lines out of the OPP constructor and
into init_hw.
Also reset the hubp power gated flag, since nothing is
power gated at init_hw.
Signed-off-by: Andrew Jiang <Andrew.Jiang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dcn10_translate_regamma_to_hw_format costs 750us to run, it cannot be
called within isr, check update flag before calling, only do it for
full update.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
