This fixes setting the clock divider on the TI OMAP-L138 LCDK board.
The clock drivers for OMAP-L138 are being covernted to the common clock
framework. When this happens, clk_set_rate() will no longer return an
error. However, on this SoC, the clock rate cannot actually be changed
because the clock has to maintain a fixed ratio to the ARM clock. So
after attempting to set the clock rate, we need to check to see if the
new rate is actually close enough. If not, then follow the previous
error path to adjust the divider in LCDC IP block to compensate for not
being able to change the parent clock rate.
Tested working on a TI OMAP-L138 LCDK board.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
This patch brings back possibility to use drivers depending on
DRM_EXYNOS, on Samsung S5PV210/S5PC110 series based systems.
Fixes: dbbc925bb8 ("drm/exynos: depend on ARCH_EXYNOS for DRM_EXYNOS")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
drm_bridge_attach takes care of these assignments, so there is no need
to open-code them a second time.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DP_TRAINING_AUX_RD_INTERVAL with DP 1.3 spec changed bit scheeme from 8
bits to 7 in DPCD 0x000e. The 8th bit is used to identify extended
receiver capabilities. For panels that use this new feature wait interval
would be increased by 512 ms, when spec is max 16 ms. This behavior is
described in table 2-158 of DP 1.4 spec address 0000eh.
With the introduction of DP 1.4 spec main link clock recovery was
standardized to 100 us regardless of TRAINING_AUX_RD_INTERVAL value.
To avoid breaking panels that are not spec compiant we now warn on
invalid values.
V2: commit title/message, masking all 7 bits, warn on out of spec values.
V3: commit message, make link train clock recovery follow DP 1.4 spec.
V4: style changes
V5: typo
V6: print statement revisions, DP_REV to DPCD_REV, comment correction
V7: typo
V8: Style
V9: Strip out DPCD_REV_XX into seperate patch
v10: DPCD_REV_XX to DP_DPCD_REV_XX
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180504221800.17830-2-matthew.s.atwood@intel.com
During request submission, we call the engine->schedule() function so
that we may reorder the active requests as required for inheriting the
new request's priority. This may schedule several tasklets to run on the
local CPU, but we will need to schedule the tasklets again for the new
request. Delay all the local tasklets until the end, so that we only
have to process the queue just once.
v2: Beware PREEMPT_RCU, as then local_bh_disable() is then not a
superset of rcu_read_lock().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180507135731.10587-2-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fix `[drm:intel_enable_lvds] *ERROR* timed out waiting for panel to
power on` in kernel log at boot time.
Toshiba Satellite Z930 laptops needs between 1 and 2 seconds to power
on its screen during Intel i915 DRM initialization. This currently
results in a `[drm:intel_enable_lvds] *ERROR* timed out waiting for
panel to power on` message appearing in the kernel log during boot
time and when stopping the machine.
This change increases the timeout of the `intel_enable_lvds` function
from 1 to 5 seconds, letting enough time for the Satellite 930 LCD
screen to power on, and suppressing the error message from the kernel
log.
This patch has been successfully tested on Linux 4.14 running on a
Toshiba Satellite Z930.
[vsyrjala: bump the timeout from 2 to 5 seconds to match the DP
code and properly cover the max hw timeout of ~4 seconds, and
drop the comment about the specific machine since this is not
a particulary surprising issue, nor specific to that one machine]
Signed-off-by: Florent Flament <contact@florentflament.com>
Cc: stable@vger.kernel.org
Cc: Pavel Petrovic <ppetrovic@acm.org>
Cc: Sérgio M. Basto <sergio@serjux.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103414
References: https://bugzilla.kernel.org/show_bug.cgi?id=57591
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419160700.19828-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 280b54ade5)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
During state readout we first read out the pipe src size, store
that information in the user mode h/vdisplay, but later on we overwrite
that with the actual crtc timings. That makes our read out crtc state
inconsistent with itself when the BIOS has enabled the panel fitter to
scale the pipe contents. Let's preserve the pipe src size based
information in the user mode to make things consistent again.
This fixes a problem introduced by commit a2936e3d9a ("drm/i915:
Use drm_mode_get_hv_timing() to populate plane clip rectangle")
where the inconsistent state is now leading the plane clipping code
to report a failure on account the plane dst coordinates not matching
the user mode size. Previously we did the plane clipping based on
the pipe src size instead and thus never noticed the inconsistency.
The failure manifests as a WARN:
[ 0.762117] [drm:intel_dump_pipe_config [i915]] requested mode:
[ 0.762142] [drm:drm_mode_debug_printmodeline [drm]] Modeline 0:"1366x768" 60 72143 1366 1414 1446 1526 768 771 777 784 0x40 0xa
...
[ 0.762327] [drm:intel_dump_pipe_config [i915]] port clock: 72143, pipe src size: 1024x768, pixel rate 72143
...
[ 0.764666] [drm:drm_atomic_helper_check_plane_state [drm_kms_helper]] Plane must cover entire CRTC
[ 0.764690] [drm:drm_rect_debug_print [drm]] dst: 1024x768+0+0
[ 0.764711] [drm:drm_rect_debug_print [drm]] clip: 1366x768+0+0
[ 0.764713] ------------[ cut here ]------------
[ 0.764714] Could not determine valid watermarks for inherited state
[ 0.764792] WARNING: CPU: 4 PID: 159 at drivers/gpu/drm/i915/intel_display.c:14584 intel_modeset_init+0x3ce/0x19d0 [i915]
...
Cc: FadeMind <fademind@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-by: FadeMind <fademind@gmail.com>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Tested-by: Dave Jones <davej@codemonkey.org.uk>
References: https://lists.freedesktop.org/archives/intel-gfx/2018-April/163186.html
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105992
Fixes: a2936e3d9a ("drm/i915: Use drm_mode_get_hv_timing() to populate plane clip rectangle")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426163015.14232-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: FadeMind <fademind@gmail.com>
(cherry picked from commit bd4cd03c81)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
On intel_dp_compute_config() we were calculating the needed vco
for eDP on gen9 and we stashing it in
intel_atomic_state.cdclk.logical.vco
However few moments later on intel_modeset_checks() we fully
replace entire intel_atomic_state.cdclk.logical with
dev_priv->cdclk.logical fully overwriting the logical desired
vco for eDP on gen9.
So, with wrong VCO value we end up with wrong desired cdclk, but
also it will raise a lot of WARNs: On gen9, when we read
CDCLK_CTL to verify if we configured properly the desired
frequency the CD Frequency Select bits [27:26] == 10b can mean
337.5 or 308.57 MHz depending on the VCO. So if we have wrong
VCO value stashed we will believe the frequency selection didn't
stick and start to raise WARNs of cdclk mismatch.
[ 42.857519] [drm:intel_dump_cdclk_state [i915]] Changing CDCLK to 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 42.897269] cdclk state doesn't match!
[ 42.901052] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 42.938004] RIP: 0010:intel_set_cdclk+0x5d/0x110 [i915]
[ 43.155253] WARNING: CPU: 5 PID: 1116 at drivers/gpu/drm/i915/intel_cdclk.c:2084 intel_set_cdclk+0x5d/0x110 [i915]
[ 43.170277] [drm:intel_dump_cdclk_state [i915]] [hw state] 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
[ 43.182566] [drm:intel_dump_cdclk_state [i915]] [sw state] 308571 kHz, VCO 8640000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
v2: Move the entire eDP's vco logical adjustment to inside
the skl_modeset_calc_cdclk as suggested by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: bb0f4aab0e ("drm/i915: Track full cdclk state for the logical and actual cdclk frequencies")
Cc: <stable@vger.kernel.org> # v4.12+
Link: https://patchwork.freedesktop.org/patch/msgid/20180502175255.5344-1-rodrigo.vivi@intel.com
(cherry picked from commit 3297234a05)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
igt_ctx_exec() expects that we retire all active requests/objects before
completing, so that when we clean up the files afterwards they are ready
to be freed. Before we do so, it is then prudent to ensure that we have
indeed retired the GPU activity, raising an error if it fails. If we do
not, we run the risk of triggering an assertion when freeing the object:
__i915_gem_free_objects:4793 GEM_BUG_ON(i915_gem_object_is_active(obj))
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180505091014.26126-2-chris@chris-wilson.co.uk
This implements the "MG PLL Programming" sequence from our spec. The
biggest problem was that the spec assumes real numbers, so we had to
adjust some numbers and calculations due to the fact that the Kernel
prefers to deal with integers.
I recommend grabbing some coffee, a pen and paper before reviewing
this patch.
v2:
- Correctly identify DP encoders after upstream change.
- Small checkpatch issues.
- Rebase.
v3:
- Try to impove the comment on the tdc_targetcnt calculation based on
Manasi's feedback (Manasi).
- Rebase.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180328215803.13835-7-paulo.r.zanoni@intel.com
This commit introduces the definitions for the ICL clocks and adds the
basic functions to the shared DPLL framework. It adds code for the
Enable and Disable sequences for some PLLs, but it does not have the
code to compute the actual PLL values, which are marked as TODO
comments and should be introduced as separate commits.
Special thanks to James Ausmus for investigating and fixing a bug with
the placement of icl_unmap_plls_to_ports() function.
v2:
- Rebase around dpll_lock changes.
v3:
- The spec now says what the timeouts should be.
- Touch DPCLKA_CFGCR0_ICL at the appropriate time so we don't freeze
the machine.
- Checkpatch found a white space problem.
- Small adjustments before upstreaming.
v4:
- Move the ICL checks out of the *map_plls_to_ports() functions
(James)
- Add extra encoder check (James)
- Call icl_unmap_plls_to_ports() later (James)
v5:
- Rebase after the pll struct changes.
v6:
- Properly make the unmap function based on encoders_post_disable()
with regarding to checks and iterators.
- Address checkpatch comment on "min = max = x()".
Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180427231436.9353-1-paulo.r.zanoni@intel.com
In the cleanup, I didn't notice that we needed to dereference the
connector for the bus_format. Fix the regression by looking up the
first (and only) connector attached to us, and assume that its
bus_format is what we want. Some day it would be good to have that
part of display_info attached to the bridge, instead.
v2: Fix stray whitespace change
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 7b1298e053 ("drm/vc4: Switch DPI to using the panel-bridge helper.")
Link: https://patchwork.freedesktop.org/patch/msgid/20180309233256.1667-1-eric@anholt.net
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Clear the old_state and new_state pointers for every object in
drm_atomic_state_default_clear(). Otherwise
drm_atomic_get_{new,old}_*_state() will hand out stale pointers to
anyone who hasn't first confirmed that the object is in fact part of
the current atomic transcation, if they are called after we've done
the ww backoff dance while hanging on to the same drm_atomic_state.
For example, handle_conflicting_encoders() looks like it could hit
this since it iterates the full connector list and just calls
drm_atomic_get_new_connector_state() for each.
And I believe we have now witnessed this happening at least once in
i915 check_digital_port_conflicts(). Commit 8b69449d26 ("drm/i915:
Remove last references to drm_atomic_get_existing* macros") changed
the safe drm_atomic_get_existing_connector_state() to the unsafe
drm_atomic_get_new_connector_state(), which opened the doors for
this particular bug there as well.
v2: Split private objs out to a separate patch (Daniel)
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Abhay Kumar <abhay.kumar@intel.com>
Fixes: 581e49fe6b ("drm/atomic: Add new iterators over all state, v3.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180502183247.5746-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
