[Why]
To debug when p-state is being blocked and avoid PMFW hangs when
it does occur.
[How]
Re-use the DCN10 hardware sequencer by adding a new interface for
verifying p-state high on the hubbub. The interface is mostly the
same as the DCN10 interface, but the bit definitions have changed for
the debug bus.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move parts of dcn20 code that uses FPU to dml folder. It aims to isolate
FPU operations as described by series:
drm/amd/display: Introduce FPU directory inside DC
https://patchwork.freedesktop.org/series/93042/
This patch moves the following functions from dcn20_resource to
dml/dcn20_fpu and calls of public functions in dcn20_resource are
wrapped by DC_FP_START/END():
- void dcn20_populate_dml_writeback_from_context
- static bool is_dtbclk_required()
- static enum dcn_zstate_support_state()
- void dcn20_calculate_dlg_params()
- static void swizzle_to_dml_params()
- int dcn20_populate_dml_pipes_from_context()
- void dcn20_calculate_wm()
- void dcn20_cap_soc_clocks()
- void dcn20_update_bounding_box()
- void dcn20_patch_bounding_box()
- bool dcn20_validate_bandwidth_fp()
This movement also affects dcn21/30/31, as dcn20_calculate_dlg_params()
is used by them. For this reason, I included dcn20_fpu headers in
dcn20_resource headers to make dcn20_calculate_dlg_params() visible to
dcn21/30/31.
Three new functions are created to isolate well-delimited FPU
operations:
- void dcn20_fpu_set_wb_arb_params(): set cli_watermark,
pstate_watermark and time_per_pixel from wb_arb_params (struct
mcif_arb_params), since those uses FPU operations on double types:
WritebackUrgentWatermark, WritebackDRAMClockChangeWatermark, '16.0'.
- void dcn20_fpu_set_wm_ranges(): set min_fill_clk_mhz and
max_fill_clk_mhz involves FPU calcs on dram_speed_mts (double type);
- void dcn20_fpu_adjust_dppclk(): adjust operation on RequiredDPPCLK
that is a double.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Calculations differ with HostVM enabled/disabled, causing underflow in
configs with high refresh displays + scaling due to lower available BW
[HOW]
Check riommu_active in order to pass correct HostVM enablement to DML
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To help triage issues and coordinate driver/bios release dependency
[How]
Only enable the new Z9 interface when debug option is set, otherwise
treat Z10 only support case as Zstate disallowed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
driver missed the check.
[how]
add the check.
add min display clock = 100mhz check based on dccg doc.
[note]
add SetPhyclkVoltageByFreq as confirmed with smu, but not enabled in
this change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
B0 PHY C map to F, D map to G driver use logic instance, dmub does the
remap. Driver still need use the right PHY instance to access right HW.
[how]
use phyical instance when program PHY register.
[note]
could move resync_control programming to dmub next.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This turns previously global functions into static, thus removing
compile-time warnings such as:
warning: no previous prototype for 'get_highest_allowed_voltage_level'
[-Wmissing-prototypes]
742 | unsigned int get_highest_allowed_voltage_level(uint32_t chip_family, uint32_t hw_internal_rev, uint32_t pci_revision_id)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
warning: no previous prototype for 'rv1_vbios_smu_send_msg_with_param'
[-Wmissing-prototypes]
102 | int rv1_vbios_smu_send_msg_with_param(struct clk_mgr_internal *clk_mgr, unsigned int msg_id, unsigned int param)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Changes since v1:
- As suggested by Rodrigo Siqueira:
1. Rewrite function signatures to make them more readable.
2. Get rid of unused functions in order to remove 'defined but not
used' warnings.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During dcn31_stream_encoder_create, if PHYC/D get remapped to F/G on B0
then we'll index 5 or 6 into a array of length 5 - leading to an
access violation on some configs during device creation.
[How]
Software won't be touching PHYF/PHYG directly, so just extend the
array to cover all possible engine IDs.
Even if it does by try to access one of these registers by accident
the offset will be 0 and we'll get a warning during the access.
Fixes: 2fe9a0e117 ("drm/amd/display: Fix DCN3 B0 DP Alt Mapping")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change since v1: add brief description
1. Add hdmi frl pcon support to existing asic family.
2. Determine pcon frl capability based on pcon dpcd.
3. pcon frl is taken into consideration into mode validation.
v2: squash in warning fix (Alex)
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Clocks don't get recalculated in 0 stream/0 pipe configs,
blocking S0i3 if dcfclk gets high enough
[HOW]
Create DCN31 copy of DCN30 bandwidth validation func which
doesn't entirely skip validation in 0 pipe scenarios
Override dcfclk to vlevel 0/min value during validation if pipe
count is 0
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some ABM registers don't exist on DCN 3.01, so are
missing from its register offset list. However,
this list was copied to later versions of DCN that
do have these registers. As a result, they're
inaccessible from the driver on those DCN versions
even though they exist.
[How]
Add the missing ABM register offsets to DCN 3.02+
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Retrieve 128/132b link cap.
2. 128/132b link training and payload allocation.
3. UHBR10 link rate support.
[squash in warning fixes - Alex]
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
