This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin
which will be used by ath10k driver to identify coex support
of a hardware and notify wifi firmware the gpio pin number.
This pin number information is needed for the hardware QCA4019.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add device tree binding documentation details for wcn3990
wifi block present in Qualcomm SDM845/APQ8098 SoC into
"qcom,ath10k.txt".
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus + bmi-chip-id + bmi-board-id is not enough to identify the correct
board data file on QCA4019 based devices. Multiple different boards share
the same values. Only the original reference designs can currently be
identified and loaded from the board-2.bin. But these will not result in
the correct calibration data when combined with the pre-calibration data
from the device.
An additional "variant" information has to be provided (via SMBIOS or DT)
to select the correct board data for a design which was modified by an ODM.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There two things done in this patch,
1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
not only calibration data, it carries board specific data too.
So, make appropriate update in doc.
2) ipq4019 wifi needs new devie tree entry to carry calibration
data alone (called pre cal data, it doesn't include any other info).
Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
the purpose of it. Hence, add new device tree entry called
'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add device tree binding documentation details for wifi block present
in Qualcomm IPQ4019 SoC into "qcom,ath10k.txt".
Right now, ath10k wireless driver has support for PCI based wlan devices.
There is a plan to extend ath10k driver to support wifi devices which are
connected over AHB as well (enumeration will happen via device tree node).
For AHB based devices (ie, ipq4019), all wifi properties are supplied via
device tree (including irq, reg addr, cal data,etc).
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Acked-by: Rob Herring <robh@kernel.org>
[kvalo@qca.qualcomm.com: fixed typos noticed by Rob]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
