Pull remoteproc updates from Bjorn Andersson:
"rproc-virtio device names are now auto generated, to avoid conflicts
between remoteproc instances.
The imx_rproc driver is extended with support for communicating with
and attaching to a running M4 on i.MX8QXP, as well as support for
attaching to the M4 after self-recovering from a crash. Support is
added for i.MX8QM and mailbox channels are reconnected during the
recovery process, in order to avoid data corruption.
The Xilinx Zynqmp firmware interface is extended and support for the
Xilinx R5 RPU is introduced.
Various resources leaks, primarily in error paths, throughout the
Qualcomm drivers are corrected.
Lastly a fix to ensure that pm_relax is invoked even if the remoteproc
instance is stopped between a crash is being reported and the recovery
handler is scheduled"
* tag 'rproc-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (25 commits)
remoteproc: core: Do pm_relax when in RPROC_OFFLINE state
remoteproc: qcom: q6v5: Fix missing clk_disable_unprepare() in q6v5_wcss_qcs404_power_on()
remoteproc: qcom_q6v5_pas: Fix missing of_node_put() in adsp_alloc_memory_region()
remoteproc: qcom_q6v5_pas: detach power domains on remove
remoteproc: qcom_q6v5_pas: disable wakeup on probe fail or remove
remoteproc: qcom: q6v5: Fix potential null-ptr-deref in q6v5_wcss_init_mmio()
remoteproc: sysmon: fix memory leak in qcom_add_sysmon_subdev()
remoteproc: sysmon: Make QMI message rules const
drivers: remoteproc: Add Xilinx r5 remoteproc driver
firmware: xilinx: Add RPU configuration APIs
firmware: xilinx: Add shutdown/wakeup APIs
firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration.
arm64: dts: xilinx: zynqmp: Add RPU subsystem device node
dt-bindings: remoteproc: Add Xilinx RPU subsystem bindings
remoteproc: core: Use device_match_of_node()
remoteproc: imx_rproc: Correct i.MX93 DRAM mapping
remoteproc: imx_rproc: Enable attach recovery for i.MX8QM/QXP
remoteproc: imx_rproc: Request mbox channel later
remoteproc: imx_rproc: Support i.MX8QM
remoteproc: imx_rproc: Support kicking Mcore from Linux for i.MX8QXP
...
Add i.MX8QXP compatible
Add a new property fsl,resource-id for SoC which supports SCFW.
This property is used to check whether remote process is under control
of Linux or not.
Add fsl,entry-address to specify the entry address which used by SCFW
to kick M4.
To i.MX8QM/QXP, when M4 is in the same hardware partition with Cortex-A
cores, need power up M4 through SCFW, then M4 could start. So introduce
power-domains property.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20221021041526.3696483-2-peng.fan@oss.nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
SMD edge contains subnodes representing devices related to the remote
processor. With limietd number of remote processors, there is a limited
set of such devices.
List all of them in smd-edge bindings so schema can strictly check for
subnodes.
Additional benefit is requirement of "qcom,smd-channels" for such
subnodes, because their schema cannot enforce it (few devices like APR
or FastRPC can be part of either SMD or GLINK edge).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220909125403.803158-8-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
GLINK edge contains subnodes representing devices related to the remote
processor. Each of such device (e.g. APR or FastRPC) must have
a "qcom,glink-channels" property. However the APR or FastRPC device can
be also part of other communication - SMD - thus their schema does not
require "qcom,glink-channels".
To make the GLINK edge bindings strict, require "qcom,glink-channels"
for its children.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220909125403.803158-6-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Qualcomm FastRPC bindings to yaml format, so that we could validate
dt-entries correctly and any future additions can go into yaml format.
Use compute-cb@ subnodes instead of just cb@. Add qcom,glink-channels and
qcom,smd-channels missing properties to make sure dtbs_check doesn't fail
right off the bat. Correct the name of the parent node in the example from
smd-edge to glink-edge.
Since now the qcom,fastrpc bindings document is yaml, update the
reference to it in qcom,glink-edge and also use $ref.
Also update the MAINTAINERS file to point to the yaml version.
Co-developed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Co-developed-by: David Heidelberg <david@ixit.cz>
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220907074301.3996021-1-abel.vesa@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for the remoteproc on Mediatek MT8188, and
enables caches for MT8186 SCP. It adds support for PRU cores found on
the TI K3 AM62x SoCs.
It moves the recovery work after a firmware crash to an unbound
workqueue, to allow recovery to happen in parallel.
A new DMA API is introduced to release dma_mem for a device.
It adds support a panic handler for the Qualcomm modem remoteproc,
with the goal of having caches flushed in memory dumps for post-mortem
debugging and it introduces a mechanism to wait for the modem firmware
on SM8450 to decrypt part of its memory for post-mortem debugging.
Qualcomm sysmon is restricted to only inform remote processors about
peers that are actually running, to avoid a race where Linux tries to
notify a recovering remote processor about its peers new state. A
mechanism for waiting for the sysmon connection to be established is
also introduced, to avoid out-of-sync updates for rapidly restarting
remote processors.
A number of Devicetree binding cleanups and conversions to YAML are
introduced, to facilitate Devicetree validation. Lastly it introduces
a number of smaller fixes and cleanups in the core and a few different
drivers"
* tag 'rproc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (42 commits)
remoteproc: qcom_q6v5_pas: Do not fail if regulators are not found
drivers/remoteproc: fix repeated words in comments
remoteproc: Directly use ida_alloc()/free()
remoteproc: Use unbounded workqueue for recovery work
remoteproc: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
remoteproc: qcom_q6v5_pas: Deal silently with optional px and cx regulators
remoteproc: sysmon: Send sysmon state only for running rprocs
remoteproc: sysmon: Wait for SSCTL service to come up
remoteproc: qcom: q6v5: Set q6 state to offline on receiving wdog irq
remoteproc: qcom: pas: Check if coredump is enabled
remoteproc: qcom: pas: Mark devices as wakeup capable
remoteproc: qcom: pas: Mark va as io memory
remoteproc: qcom: pas: Add decrypt shutdown support for modem
remoteproc: qcom: q6v5-mss: add powerdomains to MSM8996 config
remoteproc: qcom_q6v5: Introduce panic handler for MSS
remoteproc: qcom_q6v5_mss: Update MBA log info
remoteproc: qcom: correct kerneldoc
remoteproc: qcom_q6v5_mss: map/unmap metadata region before/after use
remoteproc: qcom: using pm_runtime_resume_and_get to simplify the code
remoteproc: mediatek: Support MT8188 SCP
...
Pull remoteproc updates from Bjorn Andersson:
"This fixes a race condition in the user space interface for starting
and stopping remote processors, it makes the ELF loader properly skip
zero memsz segments and it cleans up the debugfs tracefile code a bit
by not checking for errors.
It introduces support for controlling the audio DSP on Qualcomm
MSM8226, as well as audio and compute DSPs on Qualcomm SC8280XP.
It makes it possible to specify the firmware path for Mediatek's
remote processors, fixes a double free in the SCP driver and addresses
an issue with the SRAM initialization on MT8195.
Lastly it deprecates the custom ELF loader in the iMX remoteproc
driver, in favor of using the shared one"
* tag 'rproc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (21 commits)
dt-bindings: remoteproc: mediatek: Add optional memory-region to mtk,scp
dt-bindings: remoteproc: mediatek: Make l1tcm reg exclusive to mt819x
dt-bindings: remoteproc: st,stm32-rproc: Fix phandle-array parameters description
remoteproc: imx_rproc: Support i.MX93
dt-bindings: remoteproc: imx_rproc: Support i.MX93
remoteproc: qcom: pas: Add MSM8226 ADSP support
dt-bindings: remoteproc: qcom: pas: Add MSM8226 adsp
remoteproc: mediatek: Allow reading firmware-name from DT
dt-bindings: remoteproc: mediatek: Add firmware-name property
remoteproc: qcom: pas: Add sc8280xp remoteprocs
dt-bindings: remoteproc: qcom: pas: Add sc8280xp adsp and nsp pair
dt-bindings: remoteproc: mediatek: Add interrupts property to mtk,scp
remoteproc: imx_rproc: Ignore create mem entry for resource table
remoteproc: core: Move state checking to remoteproc_core
remoteproc: core: Remove state checking before calling rproc_boot()
remoteproc: imx_dsp_rproc: Make rsc_table optional
remoteproc: imx_dsp_rproc: use common rproc_elf_load_segments
remoteproc: elf_loader: skip segment with memsz as zero
remoteproc: mtk_scp: Fix a potential double free
remoteproc: Don't bother checking the return value of debugfs_create*
...
Commit ca23ecfdbd ("remoteproc/mediatek: support L1TCM") added support
for the l1tcm memory region on the MT8192 SCP, adding a new da_to_va
callback that handles l1tcm while keeping the old one for
back-compatibility with MT8183. However, since the mt8192 compatible was
missing from the dt-binding, the accompanying dt-binding commit
503c64cc42 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region")
mistakenly added this reg as if it were for mt8183. And later
it became common to all platforms as their compatibles were added.
Fix the dt-binding so that the l1tcm reg can be present only on the
supported platforms: mt8192 and mt8195.
Fixes: 503c64cc42 ("dt-bindings: remoteproc: mediatek: add L1TCM memory region")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220511195452.871897-2-nfraprado@collabora.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Qualcomm driver updates for v5.19
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
* tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
soc: qcom: pdr: use static for servreg_* variables
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains
soc: qcom: rpmhpd: Don't warn about sparse rpmhpd arrays
dt-bindings: power: rpmpd: Add sc8280xp RPMh power-domains
spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema
soc: qcom: socinfo: Sort out 8974PRO names
dt-bindings: soc: qcom,smp2p: convert to dtschema
dt-bindings: qcom: geni-se: Update UART schema reference
dt-bindings: qcom: geni-se: Update I2C schema reference
dt-bindings: soc: qcom,rpmh-rsc: convert to dtschema
bus: add driver for initializing the SSC bus on (some) qcom SoCs
dt-bindings: bus: add device tree bindings for qcom,ssc-block-bus
dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI
dt-bindings: soc: qcom,smd: convert to dtschema
firmware: qcom_scm: Add compatible for MSM8976 SoC
dt-bindings: firmware: qcom-scm: Document msm8976 bindings
soc: qcom: smem: validate fields of shared structures
soc: qcom: smem: map only partitions used by local HOST
...
Link: https://lore.kernel.org/r/20220509181839.316655-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull remoteproc updates from Bjorn Andersson:
"In the remoteproc core, it's now possible to mark the sysfs attributes
read only on a per-instance basis, which is then used by the TI wkup
M3 driver.
Also, the rproc_shutdown() interface propagates errors to the caller
and an array underflow is fixed in the debugfs interface. The
rproc_da_to_va() API is moved to the public API to allow e.g. child
rpmsg devices to acquire pointers to memory shared with the remote
processor.
The TI K3 R5F and DSP drivers gains support for attaching to instances
already started by the bootloader, aka IPC-only mode.
The Mediatek remoteproc driver gains support for the MT8186 SCP. The
driver's probe function is reordered and moved to use the devres
version of rproc_alloc() to save a few gotos. The driver's probe
function is also transitioned to use dev_err_probe() to provide better
debug support.
Support for the Qualcomm SC7280 Wireless Subsystem (WPSS) is
introduced. The Hexagon based remoteproc drivers gains support for
voting for interconnect bandwidth during launch of the remote
processor. The modem subsystem (MSS) driver gains support for probing
the BAM-DMUX driver, which provides the network interface towards the
modem on a set of older Qualcomm platforms. In addition a number a bug
fixes are introduces in the Qualcomm drivers.
Lastly Qualcomm ADSP DeviceTree binding is converted to YAML format,
to allow validation of DeviceTree source files"
* tag 'rproc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (22 commits)
remoteproc: qcom_q6v5_mss: Create platform device for BAM-DMUX
remoteproc: qcom: q6v5_wpss: Add support for sc7280 WPSS
dt-bindings: remoteproc: qcom: Add SC7280 WPSS support
dt-bindings: remoteproc: qcom: adsp: Convert binding to YAML
remoteproc: k3-dsp: Add support for IPC-only mode for all K3 DSPs
remoteproc: k3-dsp: Refactor mbox request code in start
remoteproc: k3-r5: Add support for IPC-only mode for all R5Fs
remoteproc: k3-r5: Refactor mbox request code in start
remoteproc: Change rproc_shutdown() to return a status
remoteproc: qcom: q6v5: Add interconnect path proxy vote
remoteproc: mediatek: Support mt8186 scp
dt-bindings: remoteproc: mediatek: Add binding for mt8186 scp
remoteproc: qcom_q6v5_mss: Fix some leaks in q6v5_alloc_memory_region
remoteproc: qcom_wcnss: Add missing of_node_put() in wcnss_alloc_memory_region
remoteproc: qcom: Fix missing of_node_put in adsp_alloc_memory_region
remoteproc: move rproc_da_to_va declaration to remoteproc.h
remoteproc: wkup_m3: Set sysfs_read_only flag
remoteproc: Introduce sysfs_read_only flag
remoteproc: Fix count check in rproc_coredump_write()
remoteproc: mtk_scp: Use dev_err_probe() where possible
...
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
In order to make the 'mboxes' property in the TI remoteproc examples
parseable, mailbox provider nodes are needed. Normally, the examples
have a __fixup__ node which can be used for determining each
phandle+arg entry. However, for this binding the arg cells contain a
phandle, and the __fixups__ information can't be used.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220119181053.3846613-1-robh@kernel.org
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
