make dtbs_check:
arch/arm/boot/dts/r8a7791-koelsch-single-memory-node.dtb: pmic@58: 'wdt' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/mfd/dlg,da9063.yaml
...
Change the watchdog child node names to match the DA9063 DT bindings and
the Generic Names Recommendation in the Devicetree Specification.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1dafdce285f7d14bec9e2033ac87fb30135895db.1655818230.git.geert+renesas@glider.be
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW12) do
not have external pull-up resistors, but rely on internal pull-ups being
enabled. Fortunately this is satisfied by the initial state of these
pins.
Make this explicit by enabling bias-pull-up, to remove the dependency on
initial state and/or boot loader configuration.
While at it, rename the surrounding device node from "gpio-keys" to
"keyboard", to comply with generic node name recommendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/45f38a5333feba9bea80efeb5a41a6c3f60deda2.1619785905.git.geert+renesas@glider.be
After set PROBE_PREFER_ASYNCHRONOUS flag on the mmc host drivers,
the order of /dev/mmcblkN was not fixed in some SoCs which have
multiple SDHI and/or MMCIF controllers. So, we were hard to use
such a device as rootfs by using the kernel parameter like
"root=/dev/mmcblkNpM".
According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into R-Car Gen2
board dts files. Note that, since R-Car Gen2 is even more complicated
about SDHI and/or MMCIF channels variations and they share pins,
add the aliases into board dts files instead of SoC dtsi files.
[1]
https://lore.kernel.org/linux-arm-kernel/CAPDyKFptyEQNJu8cqzMt2WRFZcwEdjDiytMBp96nkoZyprTgmA@mail.gmail.com/
Fixes: 7320915c88 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14")
Fixes: 21b2cec61c ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1613131316-30994-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Small fixes to make these DTs compliant with the adi,adv7511w and
adi,adv7513 bindings:
r8a7745-iwg22d-sodimm-dbhd-ca.dts
r8a7790-lager.dts
r8a7790-stout.dts
r8a7791-koelsch.dts
r8a7791-porter.dts
r8a7792-blanche.dts
r8a7793-gose.dts
r8a7794-silk.dts:
Remove the adi,input-style and adi,input-justification properties.
r8a7792-wheat.dts:
Reorder the I2C slave addresses of hdmi@3d and hdmi@39 and remove
the adi,input-style and adi,input-justification properties.
Signed-off-by: Ricardo Cañuelo <ricardo.canuelo@collabora.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200511110611.3142-3-ricardo.canuelo@collabora.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
To improve human readability and enable automatic validation, the tuples
in the "states" properties of device nodes compatible with
"regulator-gpio" should be grouped, as reported by "make dtbs_check":
$ make dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi0: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi1: states:0: [3300000, 1, 1800000, 0] is too long
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: Additional items are not allowed (1800000, 0 were unexpected)
arch/arm/boot/dts/r8a7791-koelsch.dt.yaml: regulator-vccq-sdhi2: states:0: [3300000, 1, 1800000, 0] is too long
...
Fix this by grouping the tuples using angle brackets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191213164115.3697-2-geert+renesas@glider.be
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
The vin port node does not have an address and thus does not need
address-cells or address size-properties.
This is flagged by dtc as follows:
# make dtbs W=1
arch/arm/boot/dts/r8a7794-silk.dtb: Warning (avoid_unnecessary_addr_size): /soc/video@e6ef0000/port: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Extend the Silk board support to include SW3, SW4, SW6 and SW12. They
are all connected via GPIO lines and handled by the gpio-keys driver.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Create a separate bus for HDMI related I2C1 and provide fallback to GPIO.
Based on work for the r8a7790/lager by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[wsa: rebased, fixed aliases, switched to named GPIOs]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Convert the R-Car E2 SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)", "Renesas CPG DIV6 Clock", and "Renesas CPG Module Stop
(MSTP) Clocks" DT bindings to the new unified "Renesas Clock Pulse
Generator / Module Standby and Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The scif_clk device node is already enabled in r8a7794.dtsi, so there is
no need to update its status again.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the R8A7794 sound device node.
Add device node for Asahi Kasei AK4643 stereo codec to the I2C1 bus.
Add the "simple-audio-card" device node to interconnect the SoC sound
device and the codec.
This patch is based on the commit 493b4da7c1 ("ARM: dts: porter: add
sound support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /regulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
This patch updates the silk device tree to use the generic properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add and enable the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
This increases the range and accuracy of supported baud rates.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7511W HDMI transmitter
(connected to DU0) and ADV7123 video DAC (connected to DU1). Add the
necessary subnodes to interconnect DU, HDMI/VDAC devices, and HDMI/VGA
connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit e488ca9f8d ("doc: dt: mtd: partitions: add compatible
property to "partitions" node"), the "partitions" subnode of an SPI
FLASH device node must have a compatible property. The partitions are no
longer detected if it is not present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commits 5cfdedb7b9 ("mtd: ofpart: move ofpart partitions to a
dedicated dt node") and fe2585e9c2 ("doc: dt: mtd: support partitions
in a special 'partitions' subnode"), having partitions as direct subnodes
of an mtd device is discouraged. Hence move the SPI FLASH partitions to a
"partitions" subnode.
Based on similar work for the koelsch board by Geert Uytterhoeven.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the VIN0 device node.
Add the device node for Analog Devices ADV7180 video decoder to I2C1 bus.
Add the necessary subnodes to interconnect VIN0 and ADV7180 devices.
Based on the Henninger VIN0/ADV8170 device tree patch by myself.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the SILK board dependent part of the MMCIF device node (the board has
eMMC chip) along with the necessary voltage regulator (note that the Vcc/Vccq
regulator is dummy -- it's required by the MMCIF driver but doesn't actually
exist on the board).
Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
