Pull char/misc/IIO driver updates from Greg KH:
"Here is the big set of char/misc/iio and other smaller driver
subsystem changes for 7.0-rc1. Lots of little things in here,
including:
- Loads of iio driver changes and updates and additions
- gpib driver updates
- interconnect driver updates
- i3c driver updates
- hwtracing (coresight and intel) driver updates
- deletion of the obsolete mwave driver
- binder driver updates (rust and c versions)
- mhi driver updates (causing a merge conflict, see below)
- mei driver updates
- fsi driver updates
- eeprom driver updates
- lots of other small char and misc driver updates and cleanups
All of these have been in linux-next for a while, with no reported
issues"
* tag 'char-misc-7.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (297 commits)
mux: mmio: fix regmap leak on probe failure
rust_binder: return p from rust_binder_transaction_target_node()
drivers: android: binder: Update ARef imports from sync::aref
rust_binder: fix needless borrow in context.rs
iio: magn: mmc5633: Fix Kconfig for combination of I3C as module and driver builtin
iio: sca3000: Fix a resource leak in sca3000_probe()
iio: proximity: rfd77402: Add interrupt handling support
iio: proximity: rfd77402: Document device private data structure
iio: proximity: rfd77402: Use devm-managed mutex initialization
iio: proximity: rfd77402: Use kernel helper for result polling
iio: proximity: rfd77402: Align polling timeout with datasheet
iio: cros_ec: Allow enabling/disabling calibration mode
iio: frequency: ad9523: correct kernel-doc bad line warning
iio: buffer: buffer_impl.h: fix kernel-doc warnings
iio: gyro: itg3200: Fix unchecked return value in read_raw
MAINTAINERS: add entry for ADE9000 driver
iio: accel: sca3000: remove unused last_timestamp field
iio: accel: adxl372: remove unused int2_bitmask field
iio: adc: ad7766: Use iio_trigger_generic_data_rdy_poll()
iio: magnetometer: Remove IRQF_ONESHOT
...
Merge series from David Lechner <dlechner@baylibre.com>:
This series is adding support for SPI controllers and peripherals that
have multiple SPI data lanes (data lanes being independent sets of
SDI/SDO lines, each with their own serializer/deserializer).
This series covers this specific use case:
+--------------+ +---------+
| SPI | | SPI |
| Controller | | ADC |
| | | |
| CS0 |--->| CS |
| SCLK |--->| SCLK |
| SDO |--->| SDI |
| SDI0 |<---| SDOA |
| SDI1 |<---| SDOB |
| SDI2 |<---| SDOC |
| SDI3 |<---| SDOD |
+--------------+ +--------+
The ADC is a simultaneous sampling ADC that can convert 4 samples at the
same time. It has 4 data output lines (SDOA-D) that each contain the
data of one of the 4 channels. So it requires a SPI controller with 4
separate deserializers in order to receive all of the information at the
same time.
This should also work for the use case in [1] as well. (Some of the
patches in this series were already submitted there). In that case the
SPI controller is used kind of like it is two separate SPI controllers,
each with its own chip select, clock, and data lines.
[1]: https://lore.kernel.org/linux-spi/20250616220054.3968946-1-sean.anderson@linux.dev/
The DT bindings are a fairly straight-forward mapping of which pins on
the peripheral are connected to which pins on the controller. The SPI
core code parses this and makes the information available to drivers.
When a peripheral driver sees that multiple data lanes are wired up, it
can chose to use them when sending messages.
The SPI message API is a bit higher-level than just specifying the
number of data lines for a SPI transfer though. I did some research on
other SPI controllers that have this feature. They tend to be the kind
meant for connecting to two flash memory chips at the same time but can
be used more generically as well. They generally have the option to
either use one lane at a time (Sean's use case), or can mirror the same
data on multiple lanes (no users of this yet) or can perform striping
of a single data FIFO/DMA stream to/from the two lanes (our use case).
For now, the API assumes that if you want to do mirror/striping, then
you want to use all available data lanes. Otherwise, it just uses the
first data lane for "normal" SPI transfers.
Jonathan writes:
IIO: New device support, features and cleanup for the 6.20/7.0 cycle.
Slightly messier than normal unfortunately due to some conflicts
and build config bugs related to I3C drivers.
One last minute Kconfig fix right at the top after a linux-next report.
I've simplified the Kconfig and made it match other instances in the kernel
so that should be safe enough despite short soak time in front of build bots.
Merge of an immutable branch from I3C to get some stubs that were missing
and caused build issues with dual I2C / I3C drivers. This also brought in a
drop of some deprecated interfaces so there is also one patch to update a
new driver to not use those.
We are having another go at using cleanup.h magic with the IIO mode claim
functions after backing out last try at this. This time we have wrappers
around the new ACQUIRE() and ACQUIRE_ERR() macros.
Having been burnt once, we will be taking it a bit more slowly this time
wrt to wide adoption of these! Thanks in particular to Kurt for taking
on this core IIO work.
New Device Support
==================
adi,ad18113
- New driver to support the AD18113 amplifier - an interesting device due
to the external bypass paths where we need to describe what gain those
paths have in DT. Longer term it will be interesting to see if this
simplistic description is enough for real deployments.
adi,ad4062
- New driver for the AD4060 and AD4052 SAR ADCs including trigger, event
and GPIO controller support. Follow up patch replaced use of some
deprecated I3C interfaces prior to the I3C immutable branch merge as
that includes dropping them.
adi,ad4134
- New driver for the AD4134 24bit 4 channel simultaneous sampling ADC.
adi,ad7768-1,
- Add support for the ADAQ767-1, ADAQ7768-1 and ADAQ7769-1 ADCs after some
rework to enable the driver to support multiple device types.
adi,ad9467
- Add support for the similar ad9211 ADC to this existing driver.
- Make the selection of 2s comp mode explicit for normal operation and
switch to offset binary when entering calibration mode.
honeywell,abp2
- New driver to support this huge family (100+) of board mount pressure and
temperature sensors.
maxim,max22007
- New drier for this 4 channel DAC.
memsic,mmc5633
- New driver for this I2C/I3C magnetometer. Follow on patches fixed up
issues related to single driver supporting both bus types.
microchip,mcp747feb02
- New driver for the Microchip MCP47F(E/V)B(0/1/2)1,
MCP47F(E/V)B(0/1/2)2, MCP47F(E/V)B(0/1/2)4 and MCP47F(E/V)B(0/1/2)8
buffered voltage output DACs.
nxp,sar-adc
- New driver support ADCs found on s32g2 and s32g3 platforms.
ti,ads1018
- New drier for the ADS1018 and ADS1118 SPI ADCs.
ti,ads131m02
- New driver supporting ADS131M(02/03/04/06/08)24-bit simultaneous sampling
ADCs.
Features
========
iio-core
- New IIO_DEV_ACQUIRE_DIRECT_MODE() / IIO_DEV_ACQUIRE_FAILED() +
equivalents for the much rarer case where the mode needs pinning
whether or not it is in direct mode. These use the ACQUIRE()
/ ACQUIRE_ERR() infrastructure underneath to provide both simple
checks on whether we got the requested mode and to provide scope
based release. Applied in a few initial drivers.
adi,ad9467
- Support calibbias control
adi,adf4377
- Add support to act as a clock provider.
adi,adxl380
- Support low power 1KHz sampling frequency mode. Required rework of
how events and filters were configured, plus applying of constraints
when in this mode.
rf-digital,rfd77402
- Add interrupt support as alternative to polling for completion.
st,lsm6dsx
- Tap event detection (after considerable driver rework)
Cleanup and Minor Fixes
=======================
More minor cleanup such as typos, white space etc not called out except
where they were applied to a lot of drivers.
Various drivers.
- Use of dev_err_probe() to cleanup error handling.
- Introduce local struct device and struct device_node variables to
reduce duplication of getting them from containing structs.
- Ensure uses of iio_trigger_generic_data_rdy_poll() set IRQF_NO_THREAD
as that function calls non threaded child interrupt handlers.
- Replace IRQF_ONESHOT in not thread interrupt handlers with
IRQF_NO_THREAD to ensure they run as intended. Drop one unnecessary case.
iio-sw-device/trigger.
- Constify configs_group_operations structures.
iio-buffer-dma / buffer-dma-engine
- Use lockdep_assert_held() to replace WARN_ON() to check lock is
correctly held.
- Make use of cleanup.h magic to simplify various code paths.
- Make iio_dma_buffer_init() return void rather than always success.
adi,ad7766
- Replace custom interrupt handler with iio_trigger_generic_data_rdy_poll()
adi,ad9832
- Drop legacy platform_data support.
adi,ade9000
- Add a maintainer entry.
adi,adt7316
- Move to EXPORT_GPL_SIMPLE_DEV_PM_OPS() and pm_sleep_ptr() so the compiler
can cleanly drop unused pm structures and callbacks.
adi,adxl345
- Relax build constraint vs the driver that is in input so both may be
built as modules and selection made at runtime.
adi,adxl380
- Make sure we don't read tail entries in the hardware fifo if a partial
new scan has been written.
- Move to a single larger regmap_noinc_read() to read the hardware fifo.
aspeed,ast2600
- Add missing interrupts property to DT binding.
bosch,bmi270_i2c
- Add missing MODULE_DEVICE_TABLE() macros so auto probing of modules can
work.
bosch,smi330
- Drop duplicate assignment of IIO_TYPE in smi330_read_avail()
- Use new common field_get() and field_prep() helpers to replace local
version.
honeywell,mprls0025pa
Fixes delayed to merge window as late in cycle and we didn't want to delay
the rest of the series.
- Allow Kconfig selection of specific bus sub-drivers rather than tying that
to the buses themselves being supported.
- Zero spi_transfer structure to avoid chance of unintentionally set fields
effecting transfer.
- Fix a potential timing violation wrt to the chip select to first clock
edge timing.
- As recent driver, take risk inherent in dropping interrupt direction from
driver as that should be set by firmware.
- Fix wrong reported number of data bits for channel.
- Fix a pressure channel calculation bug.
- Rework to allow embedding the tx buffer in the iio_priv() structure rather
than requiring separate allocation.
- Move the buffer clearing to the shared core bringing it into affect for
SPI as well as I2C.
- Stricter checks for status byte.
- Greatly simplify the measurement sequence.
- Add a copyright entry to reflect Petre's continued work on this driver.
intersil,isl29018
- Switch from spritnf to sysfs_emit_at() to make it clear overflow can't
occur.
invensense,icm42600
- Allow sysfs access to temperature when buffered capture in use as it
does not impact other sensor data paths.
invensense,itg3200
- Check unused return value in read_raw() callback.
men,z188
- Drop now duplicated module alias.
rf-digital,rfd77402
- Add DT binding doc and explicit of_device_id table.
- Poll for timeout with times as on datasheet, then replace opencoded
version with read_poll_timeout().
sensiron,scd4x
- Add missing timestamp channel. The code to push it to the buffer was there
but there was no way to turn it on.
vti,sca3000
- Fix resource leak if iio_device_register() fails.
* tag 'iio-for-7.0a' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (144 commits)
iio: magn: mmc5633: Fix Kconfig for combination of I3C as module and driver builtin
iio: sca3000: Fix a resource leak in sca3000_probe()
iio: proximity: rfd77402: Add interrupt handling support
iio: proximity: rfd77402: Document device private data structure
iio: proximity: rfd77402: Use devm-managed mutex initialization
iio: proximity: rfd77402: Use kernel helper for result polling
iio: proximity: rfd77402: Align polling timeout with datasheet
iio: cros_ec: Allow enabling/disabling calibration mode
iio: frequency: ad9523: correct kernel-doc bad line warning
iio: buffer: buffer_impl.h: fix kernel-doc warnings
iio: gyro: itg3200: Fix unchecked return value in read_raw
MAINTAINERS: add entry for ADE9000 driver
iio: accel: sca3000: remove unused last_timestamp field
iio: accel: adxl372: remove unused int2_bitmask field
iio: adc: ad7766: Use iio_trigger_generic_data_rdy_poll()
iio: magnetometer: Remove IRQF_ONESHOT
iio: Replace IRQF_ONESHOT with IRQF_NO_THREAD
iio: Use IRQF_NO_THREAD
iio: dac: Add MAX22007 DAC driver support
dt-bindings: iio: dac: Add max22007
...
Change spi-rx-bus-width and spi-tx-bus-width properties from single
uint32 values to arrays of uint32 values. This allows describing SPI
peripherals connected to controllers that have multiple data lanes for
receiving or transmitting two or more words in parallel.
Each index in the array corresponds to a physical data lane (one or more
wires depending on the bus width). Additional mapping properties will be
needed in cases where a lane on the controller or peripheral is skipped.
Bindings that make use of this property are updated in the same commit
to avoid validation errors.
The adi,ad4030 binding can now better describe the chips multi-lane
capabilities, so that binding is refined and gets a new example.
Converting from single uint32 to array of uint32 does not break .dts/
.dtb files since there is no difference between specifying a single
uint32 value and an array with a single uint32 value in devicetree.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20260123-spi-add-multi-bus-support-v6-1-12af183c06eb@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add compatibles for supported parts in the ad7768-1 family:
ADAQ7767-1, ADAQ7768-1 and ADAQ7769-1
Add property and checks for AFF gain, supported by ADAQ7767-1
and ADAQ7769-1, and for PGA gain, supported by ADAQ7768-1
and ADAQ7769-1:
adi,aaf-gain-bp
pga-gpios
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jonathan Santos <Jonathan.Santos@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add dt-bindings for AD4062 family, devices AD4060/AD4062, low-power with
monitor capabilities SAR ADCs. Each variant of the family differs in
resolution. The device contains two outputs (gp0, gp1). The outputs can
be configured for range of options, such as threshold and data ready.
The device uses a 2-wire I3C interface.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device has interrupts allocated according to the datasheet, and
the devicetree already defines the interrupt property. Address existing
warnings by allowing the property.
Signed-off-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The s32g2 and s32g3 NXP platforms have two instances of a Successive
Approximation Register ADC. It supports the raw, trigger and scan
modes which involves the DMA. Add their descriptions.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree bindings documentation for the Texas Instruments
ADS131M0x analog-to-digital converters. This family includes the ADS131M02,
ADS131M03, ADS131M04, ADS131M06, and ADS131M08 variants.
These variants differ primarily in the number of supported channels
(2, 3, 4, 6, and 8, respectively), which requires separate compatible
strings to validate the channel nodes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char/misc/IIO driver updates from Greg KH:
"Here is the big set of char/misc/iio driver updates for 6.19-rc1. Lots
of stuff in here including:
- lots of IIO driver updates, cleanups, and additions
- large interconnect driver changes as they get converted over to a
dynamic system of ids
- coresight driver updates
- mwave driver updates
- binder driver updates and changes
- comedi driver fixes now that the fuzzers are being set loose on
them
- nvmem driver updates
- new uio driver addition
- lots of other small char/misc driver updates, full details in the
shortlog
All of these have been in linux-next for a while now"
* tag 'char-misc-6.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (304 commits)
char: applicom: fix NULL pointer dereference in ac_ioctl
hangcheck-timer: fix coding style spacing
hangcheck-timer: Replace %Ld with %lld
hangcheck-timer: replace printk(KERN_CRIT) with pr_crit
uio: Add SVA support for PCI devices via uio_pci_generic_sva.c
dt-bindings: slimbus: fix warning from example
intel_th: Fix error handling in intel_th_output_open
misc: rp1: Fix an error handling path in rp1_probe()
char: xillybus: add WQ_UNBOUND to alloc_workqueue users
misc: bh1770glc: use pm_runtime_resume_and_get() in power_state_store
misc: cb710: Fix a NULL vs IS_ERR() check in probe()
mux: mmio: Add suspend and resume support
virt: acrn: split acrn_mmio_dev_res out of acrn_mmiodev
greybus: gb-beagleplay: Fix timeout handling in bootloader functions
greybus: add WQ_PERCPU to alloc_workqueue users
char/mwave: drop typedefs
char/mwave: drop printk wrapper
char/mwave: remove printk tracing
char/mwave: remove unneeded fops
char/mwave: remove MWAVE_FUTZ_WITH_OTHER_DEVICES ifdeffery
...
The Renesas RZ/N1 ADC controller is the ADC controller available in the
Renesas RZ/N1 SoCs family.
Signed-off-by: Herve Codina (Schneider Electric) <herve.codina@bootlin.com>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the compatible strings "aspeed,ast2700-adc0" and "aspeed,ast2700-adc1"
to the binding for the Aspeed ADC. These new compatibles represent the
ADC instances found on the AST2700 SoC, which are similar to the AST2600
but have their trimming data located at different SCU offset.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC of the RK3506 is similar to the one found in the RK3528
in terms of number of channels and the other implementation details.
So add a variant compatible for it, that reflects this fact.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree binding support for the AD4087 14-bit SAR ADC.
Add adi,ad4087 to the compatible enum.
A fallback compatible string to adi,ad4080 is not appropriate as the
AD4087 has different resolution (14-bit vs 20-bit) and LVDS CNV clock
count maximum (1 vs 7), requiring different driver configuration.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree binding support for the AD4086 14-bit SAR ADC.
Add adi,ad4086 to the compatible enum.
A fallback compatible string to adi,ad4080 is not appropriate as the
AD4086 has different resolution (14-bit vs 20-bit) and LVDS CNV clock
count maximum (4 vs 7), requiring different driver configuration.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree binding support for the AD4083 16-bit SAR ADC.
Add adi,ad4083 to the compatible enum.
A fallback compatible string to adi,ad4080 is not appropriate as the
AD4083 has different resolution (16-bit vs 20-bit) and LVDS CNV clock
count maximum (5 vs 7), requiring different driver configuration.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device-tree documentation for MAX14001/MAX14002 ADCs.
The MAX14001/MAX14002 are isolated, single-channel analog-to-digital
converters with programmable voltage comparators and inrush current
control optimized for configurable binary input applications.
They share the same features, but in the MAX14001 the inrush trigger
threshold, current magnitude, and current duration are all programmable,
whereas in the MAX14002 these parameters are fixed.
Co-developed-by: Kim Seer Paller <kimseer.paller@analog.com>
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Signed-off-by: Marilene Andrade Garcia <marilene.agarcia@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree binding support for the AD4081 20-bit SAR ADC.
Add adi,ad4081 to the compatible enum.
A fallback compatible string to adi,ad4080 is not appropriate as the
AD4081 has a different LVDS CNV clock count maximum (2 vs 7), requiring
different driver configuration.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree binding support for the AD4084 16-bit SAR ADC.
Add adi,ad4084 to the compatible enum.
A fallback compatible string to adi,ad4080 is not appropriate as the
AD4084 has different resolution (16-bit vs 20-bit) and LVDS CNV clock
count maximum (2 vs 7), requiring different driver configuration.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document the A/D 12-Bit successive approximation converters found in the
Renesas RZ/T2H (R9A09G077) and RZ/N2H (R9A09G087) SoCs.
RZ/T2H has two ADCs with 4 channels and one with 6.
RZ/N2H has two ADCs with 4 channels and one with 15.
Signed-off-by: Cosmin Tanislav <cosmin-gabriel.tanislav.xa@renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79112 is an ADC/GPIO with 32 channels. The channel inputs can
be used as ADC or GPIO. Using the GPIOs as IRQ sources isn't supported.
The ADC is 12-bit, supporting input voltages up to 5.7V, and separate I/O
voltage supply. Maximum SPI clock rate is 20 MHz (10 MHz with
daisy-chain configuration) and maximum sampling rate is 1MSPS.
Add a device tree binding document for the ROHM BD79112.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use correct clocks properties for the AD7124 family of ADCs.
These ADCs have an internal clock along with an optional external clock
that can be connected to the CLK pin. This pin can be wired up 3 ways:
1. Not connected - the internal clock is used.
2. Connected to an external clock (input) - the external clock is used.
3. Connected to the CLK pin on another ADC (output) - the internal clock
is used on one and the other is configured for an external clock.
The new bindings describe these 3 cases by picking one of the following:
1. Omit both clocks and #clock-cells properties.
2. Include only the clocks property with a phandle to the external clock.
3. Include only the #clock-cells property on the ADC providing the output.
The clock-names property is now deprecated and should not be used. The
MCLK signal that it refers to is an internal counter in the ADC and
therefore does not make sense as a devicetree property as it can't be
connected to anything external to the ADC. Since there is only one
possible external clock, the clock-names property is not needed anyway.
Based on the implementation of the Linux driver, it looks like the
"mclk" clock was basically being used as a control to select the power
mode of the ADC, which is not something that should be done in the
devicetree.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250828-iio-adc-ad7124-proper-clock-support-v3-1-0b317b4605e5@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ROHM BD79105 is a simple, 16-bit, 1-channel ADC with a 'CONVSTART'
pin used to start the ADC conversion. Other than the 'CONVSTART', there
are 3 supply pins (one used as a reference), analog inputs, ground and
communication pins. It's worth noting that the pin somewhat confusingly
labeled as 'DIN', is a pin which should be used as a chip-select. The IC
does not have any writable registers.
The device is designed so that the output pin can, in addition to
outputting the data, be used as a 'data-ready'-IRQ. There are cases
where the IRQ can't be used (because it is delivered via SPI data-line).
Hence, some systems may use a GPIO for polling the data readiness.
Add a compatible for the bd79105 and add the data-ready GPIO to the
binding.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/3f70f68665225be3091f8a0412e74037b6a2a88e.1754901948.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SARADC controller in most Rockchip SoCs are part of power domains
that are always powered on, i.e. PD_BUS or PD_PERI. These always powered
on power domains have typically not been described in the device tree.
Because these power domains have been left out of the device tree there
has not been any real need to properly describe the power domain of the
SARADC controller.
On RK3528 the SARADC controller is part of the PD_VPU power domain.
Add support to describe an optional power-domains for the SARADC
controller in Rockchip SoCs.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250723085654.2273324-4-jonas@kwiboo.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char / misc / IIO / other driver updates from Greg KH:
"Here is the big set of char/misc/iio and other smaller driver
subsystems for 6.17-rc1. It's a big set this time around, with the
huge majority being in the iio subsystem with new drivers and dts
files being added there.
Highlights include:
- IIO driver updates, additions, and changes making more code const
and cleaning up some init logic
- bus_type constant conversion changes
- misc device test functions added
- rust miscdevice minor fixup
- unused function removals for some drivers
- mei driver updates
- mhi driver updates
- interconnect driver updates
- Android binder updates and test infrastructure added
- small cdx driver updates
- small comedi fixes
- small nvmem driver updates
- small pps driver updates
- some acrn virt driver fixes for printk messages
- other small driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-6.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
binder: Use seq_buf in binder_alloc kunit tests
binder: Add copyright notice to new kunit files
misc: ti_fpc202: Switch to of_fwnode_handle()
bus: moxtet: Use dev_fwnode()
pc104: move PC104 option to drivers/Kconfig
drivers: virt: acrn: Don't use %pK through printk
comedi: fix race between polling and detaching
interconnect: qcom: Add Milos interconnect provider driver
dt-bindings: interconnect: document the RPMh Network-On-Chip Interconnect in Qualcomm Milos SoC
mei: more prints with client prefix
mei: bus: use cldev in prints
bus: mhi: host: pci_generic: Add Telit FN990B40 modem support
bus: mhi: host: Detect events pointing to unexpected TREs
bus: mhi: host: pci_generic: Add Foxconn T99W696 modem
bus: mhi: host: Use str_true_false() helper
bus: mhi: host: pci_generic: Add support for EM929x and set MRU to 32768 for better performance.
bus: mhi: host: Fix endianness of BHI vector table
bus: mhi: host: pci_generic: Disable runtime PM for QDU100
bus: mhi: host: pci_generic: Fix the modem name of Foxconn T99W640
dt-bindings: interconnect: qcom,msm8998-bwmon: Allow 'nonposted-mmio'
...
Fix following dt_schema warning when offload is used:
DTC [C] arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb
/home/angelo/dev-baylibre/linux-iio/arch/arm/boot/dts/xilinx/zynq-zed-adv7511-ad7606.dtb: adc@0: 'oneOf' conditional failed, one must be fixed:
'interrupts' is a required property
'io-backends' is a required property
from schema $id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
There isn't any reason that we couldn't have interrupts wired up at the
same time we are using io-backends or SPI offload, so dropping off the
related "oneOf" block entirely.
Fixes: 81fe5529e8 ("dt-bindings: iio: adc: adi,ad7606: add SPI offload properties")
Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20250526-wip-bl-ad7606-dtschema-fixes-v2-1-9bd56d039489@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
