VRR is not supported on analog signals.
Don't add freesync modes to analog displays or when
VRR is unsupported by DC.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the EDID of an analog display is not available, we can't
know the possible modes supported by the display. However, we
still need to offer the user to select from a variety of common
modes. It will be up to the user to select the best one, though.
This is how it works on other operating systems as well as the
legacy display code path in amdgpu.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This feature is useful for analog connections without EDID:
- Really old monitors with a VGA connector
- Cheap DVI/VGA adapters that don't connect DDC pins
When a connection is established through DAC load detection,
the driver is supposed to fill in the supported modes for the
display, which we already do in amdgpu_dm_connector_get_modes.
Also, because the load detection causes visible glitches, do not
attempt to poll the connector again after it was detected this
way. Note that it will still be polled after sleep/resume or
when force is enabled, which is okay.
v2:
Add dc_connection_dac_load connection type.
Properly release sink when no display is connected.
Don't print error when EDID isn't read from an analog display.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VGA connectors don't support any hotplug detection, so the kernel
needs to periodically poll them to see if a display is connected.
DVI-I connectors have hotplug detection for digital signals, and
some analog DVI cables pull up that pin to work with that.
However, in general not all DVI cables do this so we can't rely on
this feature, therefore we need to poll DVI-I connectors as well.
v2:
Call drm_kms_helper_poll_fini in amdgpu_dm_hpd_fini.
Disable/enable polling on suspend/resume.
Don't call full link detection when already connected.
v3:
Encounter CLANG build failure. Remove unused variable:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_irq.c:980:7:
error: variable 'use_polling' set but not used [-Werror,-Wunused-but-
set-variable]
980 | bool use_polling = false;
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VGA connectors don't have HPD (hotplug detection), so don't
touch any HPD related registers for VGA.
Determine whether hotplug detection is available by checking that
the interrupt source is invalid.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The new analog bit will be used with DVI-I connectors.
DVI-I connectors can connect to both digital and analog monitors
and this bit will help distinguish between those.
v2:
Sanitize analog bit based on connector type.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC determines the DRM connector type based on the
signal type, which becomes problematic when a connector may
support different signal types, such as DVI-I.
With this patch, it is now determined according to the actual
connector type for DVI-D and DVI-I connectors.
Also set the HPD (hotplug detection) flag for DVI-I connectors
to prevent regressing their digital functionality, which has
been already working.
A subsequent commit will also implement polling for DVI-I.
v2:
Only use connector type for DVI to prevent regressions
for other signal types.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
commit 0887054d14 ("drm/amd: Drop abm_level property") dropped the
abm level property in favor of sysfs control. Since then there have
been discussions that compositors showed an interest in modifying
a vendor specific property instead.
So re-introduce the abm level property, but with different semantics.
Rather than being an integer it's now an enum. One of the enum options
is 'sysfs', and that is because there is still a sysfs file for use by
userspace when the compositor doesn't support this property.
If usespace has not modified this property, the default value will
be for sysfs to control it. Once userspace has set the property stop
allowing sysfs control.
The property is only attached to non-OLED eDP panels.
Cc: Xaver Hugl <xaver.hugl@kde.org>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some extra logs to better help triage blackscreen issues.
* Dump all the links to see if they have sinks associated.
* Print the edid manufacturer & product id associated with a stream that
was just created.
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The state pointer found in the struct drm_atomic_state internals for
most object is a bit ambiguous, and confusing when those internals also
have old state and new state.
After the recent cleanups, the state pointer only use is to point to the
state we need to free when destroying the atomic state.
We can thus rename it something less ambiguous, and hopefully more
meaningful.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20251008-drm-rename-state-v2-1-49b490b2676a@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
[Why]
The main reason common modes are added is for compatibility with
clone mode when a laptop is connected to a projector or external
monitor. Since commit 978fa2f6d0 ("drm/amd/display: Use scaling
for non-native resolutions on eDP") when non-native modes are picked
for eDP the GPU scalar will be used. This is because it is inconsistent
whether eDP panels have the capability to actually drive non-native
resolutions. With panels connected to other connectors this limitation
generally doesn't exist as we the EDID will advertise support for a
number of resolutions and monitors will use built in scaling hardware.
Comparing DC and non-DC code paths the non-DC code path only adds
common modes for LVDS and eDP whereas the DC codepath does it for
all connector types.
In the past there was an experiment done to disable common mode adding
for eDP and LVDS from commit 6d396e7ac1 ("drm/amd/display: Disable
common modes for LVDS") and commit 7948afb46a ("drm/amd/display:
Disable common modes for eDP") but this was reverted in
commit a8b79b0918 ("drm/amd: Re-enable common modes for eDP and
LVDS") because it caused problems with Xorg.
[How]
Only add common modes for eDP and LVDS for DC, matching the behavior
of non-DC.
Suggested-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250924161624.1975819-2-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't update DC stream color components during atomic check. The driver
will continue validating the new CRTC color state but will not change DC
stream color components. The DC stream color state will only be
programmed at commit time in the `atomic_setup_commit` stage.
It fixes gamma LUT loss reported by KDE users when changing brightness
quickly or changing Display settings (such as overscan) with nightlight
on and HDR. As KWin can do a test commit with color settings different
from those that should be applied in a non-test-only commit, if the
driver changes DC stream color state in atomic check, this state can be
eventually HW programmed in commit tail, instead of the respective state
set by the non-blocking commit.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4444
Reported-by: Xaver Hugl <xaver.hugl@gmail.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Modifications in per asic capability means mpc.preblend flag should be used
to indicate preblend. Update relevant paths to use this flag.
Fixes: 3992305061 ("drm/amd/display: Clear DPP 3DLUT Cap")
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Right now, only selected APUs have enabled DTM v3, which allows to use
newer firmware for content protection.
We want to enable it on the dGPUs starting with DCN 3.2
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the first data point for a custom brightness curve is not 0% luminance
then the first few luminance values will be ignored.
[How]
Check signal is below first data point and if so do linear interpolation to
0 instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
dc_post_update_surfaces_to_stream needs to be called after a full update
completes in order to optimize clocks and watermarks for power. Add
missing calls before idle entry is requested to ensure optimal power.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On clients that utilize AMD_PRIVATE_COLOR properties for HDR support,
brightness sliders can include a hardware controlled portion and a
gamma-based portion. This is the case on the Steam Deck OLED when using
gamescope with Steam as a client.
When a user sets a brightness level while HDR is active, the gamma-based
portion and/or hardware portion are adjusted to achieve the desired
brightness. However, when a modeset takes place while the gamma-based
portion is in-use, restoring the hardware brightness level overrides the
user's overall brightness level and results in a mismatch between what
the slider reports and the display's current brightness.
To avoid overriding gamma-based brightness, only restore HW backlight
level after boot or resume. This ensures that the backlight level is
set correctly after the DC layer resets it while avoiding interference
with subsequent modesets.
Fixes: 7875afafba ("drm/amd/display: Fix brightness level not retained over reboot")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4551
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit replaces the utilization of i2c_add/del_adapter() with
devm_i2c_add_adapter() to reduce the amount of boilerplate. Using
devm_i2c_add_adapter() has the advantage of removing the manual
manipulation of the I2C adapter.
Suggested-by: Robert Beckett <bob.beckett@collabora.com>
Signed-off-by: Rodrigo Siqueira <siqueira@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Documentation/process/deprecated.rst recommends against the use of kmalloc
with dynamic size calculations due to the risk of overflow and smaller
allocation being made than the caller was expecting. This could lead to
buffer overflow in code similar to the memcpy in
amdgpu_dm_plane_add_modifier().
Signed-off-by: James Flowers <bold.zone2373@fastmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCE 6 was not advertised as being able to support VRR,
so let's mark it as unsupported for now.
The VRR implementation in amdgpu_dm depends on the VUPDATE
interrupt which is not registered for DCE 6.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DP validation may fail with multiple displays and higher color depths.
The sink may support others though.
[How]
When DP bandwidth validation fails, progressively fallback through:
- YUV422 8bpc (bandwidth efficient)
- YUV422 6bpc (reduced color depth)
- YUV420 (last resort)
This resolves cases where displays would show no image due to insufficient
DP link bandwidth for the requested RGB mode.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
fill_stream_properties_from_drm_display_mode() will not configure pixel
encoding to YCBCR422 when the DRM color format supports YCBCR422 but not
YCBCR420 or YCBCR4444. Instead it will fallback to RGB.
[How]
Add support for YCBCR422 in pixel encoding mapping.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds the pixel_clock field to the display config
struct so that power management (DPM) can use it.
We currently don't have a proper bandwidth calculation on old
GPUs with DCE 6-10 because dce_calcs only supports DCE 11+.
So the power management (DPM) on these GPUs may need to make
ad-hoc decisions for display based on the pixel clock.
Also rename sym_clock to pixel_clock in dm_pp_single_disp_config
to avoid confusion with other code where the sym_clock refers to
the DisplayPort symbol clock.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The error message "failed to initialize sw for display support" is used
for both DRM device and vblank initialization failures, making it difficult
to identify the specific failure during troubleshooting.
[How]
Update the vblank initialization error message to
"failed to initialize vblank for display support"
to distinguish it from the DRM device init failure.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a `scale` sysfs attribute that can be used to indicate when
non-linear brightness scaling is in use. As Custom brightness curves
work by linear interpolation of points the scale is no longer linear.
[How]
Indicate non-linear scaling when custom brightness curves in use and
linear scaling otherwise.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <superm1@kernel.org>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM should be able to control HDCP retry limit via configurable
parameter.
[How]
Expose a retry_limit parameter for controlling the maximum number of
retries and lift the hardcode out to DM.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes a bug where unbinding of the GPU would leave the oem i2c adapter
registered resulting in a null pointer dereference when applications try
to access the invalid device.
Fixes: 3d5470c973 ("drm/amd/display/dm: add support for OEM i2c bus")
Cc: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Geoffrey McRae <geoffrey.mcrae@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for v6.18:
Cross-subsystem Changes:
- Update a number of DT bindings for STM32MP25 Arm SoC
Core Changes:
gem:
- Simplify locking for GPUVM
panel-backlight-quirks:
- Add additional quirks for EDID, DMI, brightness
sched:
- Fix race condition in trace code
- Clean up
sysfb:
- Clean up
Driver Changes:
amdgpu:
- Give kernel jobs a unique id for better tracing
amdxdna:
- Improve error reporting
bridge:
- Improve ref counting on bridge management
- adv7511: Provide SPD and HDMI infoframes
- it6505: Replace crypto_shash with sha()
- synopsys: Add support for DW DPTX Controller plus DT bindings
gud:
- Replace simple-KMS pipe with regular atomic helpers
imagination:
- Improve power management
- Add support for TH1520 GPU
- Support Risc-V architectures
ivpu:
- Clean up
nouveau:
- Improve error reporting
panthor:
- Fail VM bind if BO has offset
- Clean up
rcar-du:
- Make number of lanes configurable
rockchip:
- Add support for RK3588 DPTX output
rocket:
- Use kfree() and sizeof() correctly
- Test DMA status
- Clean up
sitronix:
- st7571-i2c: Add support for inverted displays and 2-bit grayscale
- Clean up
stm:
- ltdc: Add support support for STM32MP257F-EV1 plus DT bindings
tidss:
- Convert to kernel's FIELD_ macros
v3d:
- Improve job management and locking
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250904090932.GA193997@linux.fritz.box
Certain OLED devices malfunction on specific brightness levels.
Specifically, when DP_SOURCE_BACKLIGHT_LEVEL is written to with
the first byte being 0x00 and sometimes 0x01, the panel forcibly
turns off until the device sleeps again.
Below are some examples. This was found by iterating over brighness
ranges while printing DP_SOURCE_BACKLIGHT_LEVEL. It was found that
the screen would malfunction on specific values, and some of them
were collected.
Therefore, introduce a quirk where the minor byte of brightness is
OR'd with 0x03 to avoid the range of invalid values.
This quirk was tested by removing the workarounds and iterating
from 0 to 50_000 value ranges with a cadence of 0.2s/it. The
range of the panel is 1000...400_000, so the values were slightly
interpolated during testing. The custom brightness curve added on
6.15 was disabled.
86016: 10101000000000000
86272: 10101000100000000
87808: 10101011100000000
251648: 111101011100000000
251649: 111101011100000001
86144: 10101000010000000
87809: 10101011100000001
251650: 111101011100000010
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3803
Tested-by: Philip Müller <philm@manjaro.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250829145541.512671-5-lkml@antheas.dev
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
