Reject modes with a pixel clock higher than the maximum display
clock. Use 400 MHz as a fallback value when the maximum display
clock is not known. Pixel clocks that are higher than the display
clock just won't work and are not supported.
With the addition of the YUV422 fallback, DC can now accidentally
select a mode requiring higher pixel clock than actually supported
when the DP version supports the required bandwidth but the clock
is otherwise too high for the display engine. DCE 6-10 don't
support these modes but they don't have a bandwidth calculation
to reject them properly.
Fixes: db291ed173 ("drm/amd/display: Add fallback path for YCBCR422")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust the nominal (and performance) clocks for DCE 8-10,
and set them to 625 MHz, which is the value used by the legacy
display code in amdgpu_atombios_get_clock_info.
This was tested with Hawaii, Tonga and Fiji.
These GPUs can output 4K 60Hz (10-bit depth) at 625 MHz.
The extra 15% clock was added as a workaround for a Polaris issue
which uses DCE 11, and should not have been used on DCE 8-10 which
are already hardcoded to the highest possible display clock.
Unfortunately, the extra 15% was mistakenly copied and kept
even on code paths which don't affect Polaris.
This commit fixes that and also adds a check to make sure
not to exceed the maximum DCE 8-10 display clock.
Fixes: 8cd61c313d ("drm/amd/display: Raise dispclk value for Polaris")
Fixes: dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Apparently, both DCE 6.0 and 6.4 have 3 PLLs, but PLL0 can only
be used for DP. Make sure to initialize the correct amount of PLLs
in DC for these DCE versions and use PLL0 only for DP.
Also, on DCE 6.0 and 6.4, the PLL0 needs to be powered on at
initialization as opposed to DCE 6.1 and 7.x which use a different
clock source for DFS.
The following functions were used as reference from the old
radeon driver implementation of DCE 6.x:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Reviewed-by: Rodrigo Siqueira <siqueira@igalia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The variable dp_ref_clk_khz is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
