[Why]
When usb4 link training fails, the dpia sym clock will be disabled and SYMCLK
source should be changed back to phy clock. In enable_streams, it is
assumed that link training succeeded and will switch from refclk to
phy clock. But phy clk here might not be on. Dig reg access timeout
will occur.
[How]
When enable_stream is hit, check if link training failed for usb4.
If it did, fall back to the ref clock to avoid reg access timeout.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Zhongwei <Zhongwei.Zhang@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On DCN20 & DCN30, the 6th DPP's & HUBP's are powered on permanently and
cannot be power gated. Thus, when dpp_reset() is invoked for the DPP5,
while it's still powered on, the cached cursor_state
(dpp_base->pos.cur0_ctl.bits.cur0_enable)
and the actual state (CUR0_ENABLE) bit are unsycned. This can cause a
double cursor in full screen with non-native scaling.
[How]
Force disable cursor on DPP5 on plane powerdown for ASICs w/ 6 DPPs/HUBPs.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4673
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We require an interlock between driver and firmware for upcoming
features and given that this could possibly happen on any single
cursor programming call (and that we can't asynchronously wait for
firmware to respond because of it) we'd be regressing cursor performance
by at least an extra 40us per call.
When we could possibly have cursor update every 20us - 100s from high
frequency gaming mice this means that we'd be stuttering or dropping
updates and impacting overall cursor performance.
We want a solution that can:
1. Interlock between other firmware features
2. Not stall out or require the DMCUB lock for every single update
[How]
When cursor offloading is enabled and supported by an ASIC driver will
route the cursor programming through to DMU as part of the regular
DC stream cursor programming interfaces for attributes and position.
The atomic pipe programming version will not be updated: this will still
follow the existing programming path by keeping track of a field that
specifies when the register writes should be deferred to DMU.
Cursor locking is not required when cursor offload is in progress since
the updates are consolidated and processed by DMU once at the end
of the frame in a periodic manner.
The shared buffer the firmware queries from is allocated along with the
rest of the scratch state region in an area that's accessible by
both firmware and driver.
The size of the cursor offload (v1) state will not change, but it does
have a unique union per ASIC version with room for expansion if needed.
When firmware features notifying DMU of DRR updates are not enabled we
now send an explicit vtotal min/max update via driver to DMU firmware
whenever the vtotal max changes. This is to allow the cursor programming
to determine the appropriate latch update point offset from vupdate.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Newer DCN use the DMCUB HW lock via inbox0 for performance reasons while
older ones will use inbox1.
The should_use_dmub_lock() function does not describe whether the lock
in general should be used, but whether it should be used via inbox1.
[How]
Rename the function to should_use_dmub_inbox1_lock() to reflect this.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's possible to have a stream enabled without a link or link encoder.
There are cases where we'd still like to interlock the driver
programming from firmware programming to ensure that we don't put the
hardware in an undefined (or error) state if two programming sequences
are simultaneously executed on the same hardware blocks.
[How]
Add an explicit DC parameter to should_use_dmub_lock().
Make pointers to should_use_dmub_lock() const since it's a checker
function that shouldn't modify state.
Update the callsites to pass in DC explicitly.
Check that the link is non-NULL before deferencing and performing link
based checks.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove this flag as the driver stopped managing it individually since
commit a4056c2a63 ("drm/amd/display: use HW hdr mult for brightness
boost"). After some back and forth it was reintroduced as a condition to
`set_output_transfer_func()` in [1]. Without direct management, this
flag only changes value when all surface update flags are set true on
UPDATE_TYPE_FULL with no output TF status meaning.
Fixes: bb622e0c00 ("drm/amd/display: program output tf when required") [1]
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If symclk RCO is enabled, stream encoder may not be receiving an ungated
clock by the time we attempt to set stream attributes when setting dpms
on. Since the clock is gated, register writes to the stream encoder fail.
[HOW]
Move set_stream_attribute call into enable_stream, just after the point
where symclk32_se is ungated.
Logically there is no need to set stream attributes as early as is
currently done in link_set_dpms_on, so this should have no impact beyond
the RCO fix.
Reviewed-by: Ovidiu (Ovi) Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN35 is having “DC: failed to blank crtc!” when running HPO
test cases. It's caused by not having sufficient udelay time.
[how]
Replace the old wait_for_blank_complete function with fsleep function to
sleep just until the next frame should come up. This way it doesn't poll
in case the pixel clock or other clock was bugged or until vactive and
the vblank are hit again.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wen Chen <Wen.Chen3@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Adjusting otg dto programming in this path is unsafe otg may be en at
this time, swapping its src sel for example was discovered to cause
visual artifacts and was moved to dcn31_program_pix_clk (where otg is
guaranteed off) but dto functional clk enable bit is not cleared.
dcn31_program_pix_clk is called during dpms on, so until that point
we will have a otg with functional src sel set (Sel DTBclk) and that
functional clk dto en is unset (i.e DTB DTO EN), which is invalid and tg
will not function and system will hang on something such as flip
incoming from OS during dpms off. will scope out dcn315 as it was
affecting diags tests on certain CI machines (not crbs)
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The boolean fast_validate is used as an
input parameter in multiple functions. To
support more scenarios, we are
replacing it with enum dc_validate_mode.
[How]
The enum dc_validate_mode introduces three
possible values:
1) DC_VALIDATE_MODE_AND_PROGRAMMING:
Apply the mode to hardware
2) DC_VALIDATE_MODE_ONLY:
Check whether the mode can be supported
3) DC_VALIDATE_MODE_AND_STATE_INDEX:
Check if the mode can be supported, and
determine the optimal voltage level
needed to support it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Color gamut_remap state log may be not available for some hw versions,
so prevent null pointer dereference by checking if there is a function
to collect data for this hw version.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Triplebuffer should be programmed on all pipes.
Some code assumed it only needed to be called on top
pipe, but as the HWSS function does not account
for that, it must be called on every pipe.
[HOW]
Remove condition to not program triplebuffer
on non-top/next pipe. Call the function
unconditionally on all pipes.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Sung Lee <Sung.Lee@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are several gaps that can result in SubVP being enabled with
incompatible HW cursor sizes, and unjust restrictions to cursor size due
to wrong predictions on future usage of SubVP.
[HOW]
- remove "prediction" logic in favor of tagging based on previous SubVP
usage
- block SubVP if current HW cursor settings are incompatible
- provide interface for DM to determine if HW cursor should be disabled
due to an attempt to enable SubVP
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are several gaps that can result in SubVP being enabled with
incompatible HW cursor sizes, and unjust restrictions to cursor size due
to wrong predictions on future usage of SubVP
[HOW]
- remove "prediction" logic in favor of tagging based on previous SubVP
usage
- block SubVP if current HW cursor settings are incompatible
- provide interface for DM to determine if HW cursor should be disabled
due to an attempt to enable SubVP
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix was previously in 25.20 but was reverted out as it was accompanied
by other changes that caused regression.
[why&how]
Disabling dtb as the dto src during dpms off relies on in the same
instance being able to also alter the dto src bit to dpref (or not dtb
in general), but this was recently changed to only take place in
dcn31_program_pix_clk, as that is where we want to perform any dto src
changes because tg is off at that point, it is unsafe to do that
elsewhere. What this means is now instead of disabling dtb as dto src
and modifying source bit, we are left with the configuration for a given
tg that specifies dtb as dto src and dtb dto en simultaneously is unset.
dcn31_program_pix_clk can rectify this but its possible for us to
perform some tg dependant operation that would simply hang because when
we go to enable say crtc then, the clk we specify as dto src is "off" en
bit is cleared, source bit was never changed, and program_pix_clk hasnt
been called yet (as apart of dpms on)
We cant disable it as dto src during dpms off if we want the luxury of
performing tg dependant operation during dpms off and before dpms on.
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When link training fails, the phy clock will be disabled. However, in
enable_streams, it is assumed that link training succeeded and the
mux selects the phy clock, causing a hang when a register write is made.
[How]
When enable_stream is hit, check if link training failed. If it did, fall
back to the ref clock to avoid a hang and keep the system in a recoverable
state.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Brendan Tam <Brendan.Tam@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
There are a few cleanup and refactoring tasks that need to be done
with the DML2.1 wrapper and DC interface to remove dependencies on
legacy structures and N-1 prototypes.
[How]
Implemented pipe_ctx->global_sync.
Implemented new functions to use pipe_ctx->hubp_regs and
pipe_ctx->global_sync:
- hubp_setup2
- hubp_setup_interdependent2
- Several other new functions for DCN 4.01 to support newer structures
Removed dml21_update_pipe_ctx_dchub_regs
Removed dml21_extract_legacy_watermark_set
Removed dml21_populate_pipe_ctx_dlg_param
Removed outdated dcn references in DML2.1 wrapper.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit addresses a null pointer dereference issue in
dcn20_program_pipe(). Previously, commit 8e4ed3cf16 ("drm/amd/display:
Add null check for pipe_ctx->plane_state in dcn20_program_pipe")
partially fixed the null pointer dereference issue. However, in
dcn20_update_dchubp_dpp(), the variable pipe_ctx is passed in, and
plane_state is accessed again through pipe_ctx. Multiple if statements
directly call attributes of plane_state, leading to potential null
pointer dereference issues. This patch adds necessary null checks to
ensure stability.
Fixes: 8e4ed3cf16 ("drm/amd/display: Add null check for pipe_ctx->plane_state in dcn20_program_pipe")
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Zicheng Qu <quzicheng@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want to clean up unnecessary asserts, one of which is an assert in
resource_is_pipe_type that fires if a pipe has no stream and still has
pointers to other pipes ("dangling state"). This gets hit because pipes
are not properly cleaned up in reset_back_end_for_pipe. When resetting a
pipe, the existing MPCC / ODM combine pointers are no longer valid,
especially when we put ODM in bypass.
[How]
- reset pipe pointers in reset_back_end_for_pipe
- remove useless code to avoid confusion
(a long time ago it had a reason to be there, not anymore)
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a known HW bug that causes the internal 3DLUT fetch signal to
be lost at VREADY, regardless of whether the OTG lock is being held or
not. A workaround is necessary to make sure that this internal signal
stays up after OTG unlock.
[How]
Set the 3DLUT_ENABLE bit immediately before and after the unlock. Also
use VUPDATE_KEEPOUT to prevent lock transition in the region between
VSTARTUP and VREADY, which could cause issues with this WA sequence.
Also including misc. 3DLUT DMA-related sequence fixes to address a few
regressions causing corruption.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn32_blank_phantom() does not consider the subVP+ODM case when blanking.
Only one of the pipes will get blanked. Remaining pipes are not blanked.
Will cause underflow in the phantom pipe when enabling the CRTC.
[How]
Use blank_pixel_data() instead of blank_phantom().
remove dcn32_blank_phantom() since logic is identical.
Different DPG dimensions get programmed when blanking phantom pipes.
Previously had phantom pipes use DPG dimensions of the main stream.
Now use DPG dimensions of the phantom streams
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In cases where an MPO plane is being dragged around partially off-screen,
it is possible to get a flip where the only scaling parameters to change
are the clip rect size and position. Currently, clip rect size changes
are considered medium updates, which can result in the clip rect being used
for HW programming being larger than the clip rect that was used for the
last DML validation. This can lead to mismatches in different parts of the
pipe and can result in a p-state hang.
[How]
- consider clip rect size changes scaling changes, therefore full updates
- refactor get_scaling_info_update_type for clarity
- remove clip_size_change update flag
Clip rect size changes were previously demoted from full updates as an
optimization when the MPO + ODM policy changed to always pre-allocate MPO
pipes, but it created the issue described above. Personally testing this
use case, the performance feels fine with full update spam, and we expect
this is a fairly infrequent use case. If the performance needs to be
optimized in the future, consider reworking the entire update type logic
to run a DML pass and determine the update type based on what DML says
will actually change.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit adds a null check for the set_output_gamma function pointer
in the dcn20_set_output_transfer_func function. Previously,
set_output_gamma was being checked for null at line 1030, but then it
was being dereferenced without any null check at line 1048. This could
potentially lead to a null pointer dereference error if set_output_gamma
is null.
To fix this, we now ensure that set_output_gamma is not null before
dereferencing it. We do this by adding a null check for set_output_gamma
before the call to set_output_gamma at line 1048.
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit addresses a null pointer dereference issue in the
`dcn20_program_pipe` function. The issue could occur when
`pipe_ctx->plane_state` is null.
The fix adds a check to ensure `pipe_ctx->plane_state` is not null
before accessing. This prevents a null pointer dereference.
Reported by smatch:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn20/dcn20_hwseq.c:1925 dcn20_program_pipe() error: we previously assumed 'pipe_ctx->plane_state' could be null (see line 1877)
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some interface functions are defined in both the public and private HWSS
interfaces, which can lead to confusion and runtime issues, therefore
the duplicates should be eliminated.
[How]
- power_down should only be private, because it's only used within HWSS.
- update_plane_addr should only be public, as it's used outside HWSS.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as stream_enc and dc->bw_vbios, are null checked previously
in the same function, so Coverity warns "implies that stream_enc and
dc->bw_vbios might be null". They are used multiple times in the
subsequent code and need to be checked.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
