[why]
Direct DIO registers access in hwseq layer was creating register conflicts.
[how]
Migrated DIO registers from hwseq to dio component.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Bhuvanachandra Pinninti <bpinnint@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A backport of the change made for DCN401 that addresses an issue where
we turn off the PHY PLL when disabling TMDS output, which causes the
OTG to remain stuck.
The OTG being stuck can lead to a hang in the DCHVM's ability to ACK
invalidations when it thinks the HUBP is still on but it's not receiving
global sync.
The transition to PLL_ON needs to be atomic as there's no guarantee
that the thread isn't pre-empted or is able to complete before the
IOMMU watchdog times out.
[How]
Backport the implementation from dcn401 back to dcn35.
There's a functional difference in when the eDP output is disabled in
dcn401 code so we don't want to utilize it directly.
Reviewed-by: Yihan Zhu <yihan.zhu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Double cursor when switching between hardware and software cursor when
dragging an MPO window can occur with cursor offload enabled.
The abort cursor update in the full programming path is responsible for
this issue since it does not reset the pipe mask when attempting to
submit an empty update.
The firmware programs the payload as requested which may contain
invalid or stale data for the previously enabled pipes, resulting in
an offset or double cursor.
[How]
For performance we don't want to memset the entire payload structure
due to its size, so just reset the pipe mask which will indicate the
payload data is empty.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- After the addition of all OVT patches, DSC padding was being accounted
for multiple times, effectively doubling the padding
- This caused compliance failures or corruption
[HOW]
- Add padding to DSC pic width when required by HW, and do not re-add
when calculating reg values
- Do not add padding when computing PPS values, and instead track padding
separately to add when calculating slice width values
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Cursor lines per chunk must be assigned from hubp->att and not
hubp->pos (the one in hubp->pos is unassigned)
- In DCN401 DPP, cur0_enable in attribute struct must be assigned
as this is the field passed to DMU
- DCN401 should not program position in driver if offload is enabled
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
Enabling/disabling DCCG RCG should be done as a last-level step when
enabling/disable blocks. This is handled by HWSS root_clock_control
already during optimize_bandwidth.
However, dccg35_dpp_root_clock_control was missing the RCG enable
call on the disable path.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We require an interlock between driver and firmware for upcoming
features and given that this could possibly happen on any single
cursor programming call (and that we can't asynchronously wait for
firmware to respond because of it) we'd be regressing cursor performance
by at least an extra 40us per call.
When we could possibly have cursor update every 20us - 100s from high
frequency gaming mice this means that we'd be stuttering or dropping
updates and impacting overall cursor performance.
We want a solution that can:
1. Interlock between other firmware features
2. Not stall out or require the DMCUB lock for every single update
[How]
When cursor offloading is enabled and supported by an ASIC driver will
route the cursor programming through to DMU as part of the regular
DC stream cursor programming interfaces for attributes and position.
The atomic pipe programming version will not be updated: this will still
follow the existing programming path by keeping track of a field that
specifies when the register writes should be deferred to DMU.
Cursor locking is not required when cursor offload is in progress since
the updates are consolidated and processed by DMU once at the end
of the frame in a periodic manner.
The shared buffer the firmware queries from is allocated along with the
rest of the scratch state region in an area that's accessible by
both firmware and driver.
The size of the cursor offload (v1) state will not change, but it does
have a unique union per ASIC version with room for expansion if needed.
When firmware features notifying DMU of DRR updates are not enabled we
now send an explicit vtotal min/max update via driver to DMU firmware
whenever the vtotal max changes. This is to allow the cursor programming
to determine the appropriate latch update point offset from vupdate.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-OVT compliance testing for 5120x2880p300Hz YCbCr420 was failing due to
incorrect slice width being calculated
[How]
-Ensure slice width is divisible by 2 for 420 to comply with spec
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For non-zero DSC instances it's possible that the HUBP domain required
to drive it for sequential ONO ASICs isn't met, potentially causing
the logic to the tile to enter an undefined state leading to a system
hang.
[HOW]
Add more checks to ensure that the HUBP domain matching the DSC instance
is appropriately powered.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why&how]
It is possible for an update to acquire otg lock and begin programming
while the previous update has not completed and its values have not
latched. The correct way to go about this is to wait until the vupdate
pulses so we can be sure that previous updates have latched and we can
continue with the current update pipe programming, otherwise during
consecutive full updates we will have corruption flash on the screen.
The corruption flash occurs specifically on configs that require odm
combine, and its local to a specific pipe (will not flash across whole
screen). This ticket is across the otg slave, but it may also appear
across master.
Reviewed-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When HUBP is power gated, the SW state can get out of sync with the
hardware state causing cursor to not be programmed correctly.
[How]
Similar to DPP, add a HUBP reset function which is called wherever
HUBP is initialized or powergated. This function will clear the cursor
position and attribute cache allowing for proper programming when the
HUBP is brought back up.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Sung Lee <sung.lee@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a few cleanup and refactoring tasks that need to be done
with the DML2.1 wrapper and DC interface to remove dependencies on
legacy structures and N-1 prototypes.
[How]
Implemented pipe_ctx->global_sync.
Implemented new functions to use pipe_ctx->hubp_regs and
pipe_ctx->global_sync:
- hubp_setup2
- hubp_setup_interdependent2
- Several other new functions for DCN 4.01 to support newer structures
Removed dml21_update_pipe_ctx_dchub_regs
Removed dml21_extract_legacy_watermark_set
Removed dml21_populate_pipe_ctx_dlg_param
Removed outdated dcn references in DML2.1 wrapper.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Driver disable will deallocate framebuffer to reset IPS state, this will cause IPS start with
INIT state to blindly power gate ONO region to break power sequence. All the gating blocks
should be powered up when releasing hw to ensure all the power optimizations are identical to pre-OS.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Yihan Zhu <Yihan.Zhu@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot skips MPC init for the active pipe, resulting in stale MPC
rate control state being retained. This will cause issues since other
logic assumes it is disabled (as DCN30 and newer does not need it).
[How]
Disable MPC rate control on ODM pipe update to cover the seamless boot
case.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mmhubbub_warmup is a field that was only read by the just removed
dc_stream_warmup_writeback() function.
Remove the field and it's initialisers.
It was only ever initialised to a single function value
(dcn30_mmhubbub_warmup) which is called explicitly elsewhere.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Implement the new backlight_level_params structure as part of the VBAC
framework, the information in this structure is needed to be passed down
to the DMCUB to identify the backlight control type, to adjust the
backlight of the panel and to perform any required conversions from PWM
to nits or vice versa.
[How]
Modified existing functions to include the new backlight_level_params
structure.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Kaitlyn Tse <Kaitlyn.Tse@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It makes DSC enable when we commit the stream which need
keep power off, and then it will skip to disable DSC if
pipe reset at this situation as power has been off. It may
cause the DSC unexpected enable on the pipe with the
next new stream which doesn't support DSC.
[HOW]
Check the DSC used on current pipe status when update stream.
Skip to enable if it has been off. The operation enable
DSC should happen when set power on.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
enable dpp rcg before we disable dppclk in hw_init cause system
hang/reboot
[How]
we remove dccg rcg related code from init into a separate function and
call it after we init pipe
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Qili Lu <qili.lu@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc_state_destruct() nulls the resource context of the DC state. The pipe
context passed to dcn35_set_drr() is a member of this resource context.
If dc_state_destruct() is called parallel to the IRQ processing (which
calls dcn35_set_drr() at some point), we can end up using already nulled
function callback fields of struct stream_resource.
The logic in dcn35_set_drr() already tries to avoid this, by checking tg
against NULL. But if the nulling happens exactly after the NULL check and
before the next access, then we get a race.
Avoid this by copying tg first to a local variable, and then use this
variable for all the operations. This should work, as long as nobody
frees the resource pool where the timing generators live.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3142
Fixes: 06ad7e1642 ("drm/amd/display: Destroy DC context while keeping DML and DML2")
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In certain scenarios DC can internally trigger back to back full updates
which will miss some required programming that is normally deferred
until post update via optimize_bandwidth.
[HOW]
In back to back update scenarios, wait for pending updates to complete
and perform any strictly required outstanding programming.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The commit 5034b935f6 ("drm/amd/display: Modify DHCUB waterwark
structures and functions") introduced a code refactor for DCHUB, but
during the merge process into amd-staging-drm-next, the program det
segments were removed. This commit adds the DET segment programming for
DCN35.
Fixes: 5034b935f6 ("drm/amd/display: Modify DHCUB waterwark structures and functions")
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some interface functions are defined in both the public and private HWSS
interfaces, which can lead to confusion and runtime issues, therefore
the duplicates should be eliminated.
[How]
- power_down should only be private, because it's only used within HWSS.
- update_plane_addr should only be public, as it's used outside HWSS.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
We calculate static screen wait frames based
on the current timing info in the active stream.
If stream is not initialized, then we should skip
the calculation and go with the default values.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The null checks for res_pool->dccg are redundant as it was already
dereferenced previously, as reported by Coverity; therefore the
null checks are removed.
This fixes 6 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Empty SST TUs are illegal to transmit over a USB4 DP tunnel.
Current policy is to configure stream encoder to pack 2 pixels per pclk
even when ODM combine is not in use, allowing seamless dynamic ODM
reconfiguration. However, in extreme edge cases where average pixel
count per TU is less than 2, this can lead to unexpected empty TU
generation during compliance testing. For example, VIC 1 with a 1xHBR3
link configuration will average 1.98 pix/TU.
[HOW]
Calculate average pixel count per TU, and block 2 pixels per clock if
endpoint is a DPIA tunnel and pixel clock is low enough that we will
never require 2:1 ODM combine.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Missing check for when there is new pipe configuration but both cur_pipe
and new_pipe are both populated causing update_state of DSC for that
instance not being updated correctly.
This causes some display mode changes to cause underflow since DSCCLK
is still gated when the display requires DSC.
[How]
Added another condition in the new pipe addition branch that checks if
there is a new pipe configuration and if it is not the same as cur_pipe.
cur_pipe does not necessarily have to be NULL to go in this branch.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently 3-tap chroma subsampling is used for YCbCr422/420. When ODM
pipesplit is used, pixels on the left edge of ODM slices need one extra
pixel from the right edge of the previous slice to calculate the correct
chroma value.
Without this change, the chroma value is slightly different than
expected. This is usually imperceptible visually, but it impacts test
pattern CRCs for compliance test automation.
[HOW]
Update logic to use the register for adding extra left edge pixel for
YCbCr422/420 ODM cases.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
