Ensure that the DAC output is enabled at the correct time by
moving it to the DCE link encoder similarly to how digital
outputs are enabled.
This also removes the call to DAC1EncoderControl from the DCE
HWSS, which always felt like it was a hacky solution.
Fixes: 0fbe321a93 ("drm/amd/display: Implement DCE analog link encoders (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN 3.6+ hardware supports CRC-32 polynomial in addition to the
legacy CRC-16. Enable 32-bit CRC values per color component for
improvement of precision in display validation.
[How]
When userspace sets crc_poly_mode (0=CRC-16, 1=CRC-32) via the debugfs
interface, the value is stored in dm_irq_params.crc_poly_mode. When CRC
source configuration triggers amdgpu_dm_crtc_configure_crc_source(),
crc_poly_mode is retrieved from dm_irq_params and passed to
dc_stream_configure_crc().
In the DC layer, dc_stream_configure_crc() sets crc_poly_mode into the
crc_params structure and passes it to optc35_configure_crc(). If the
hardware supports the OTG_CRC_POLY_SEL register, the register is
programmed to select CRC-16 or CRC-32 polynomial.
When reading CRC values, optc35_get_crc() checks whether CRC32 register
masks are available. If present, it reads 32-bit CRC values from
OTG_CRC0/1_DATA_R32/G32/B32 registers; otherwise, it falls back
to reading 16-bit CRC values from legacy OTG_CRC0/1_DATA_RG/B
registers.
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Direct DIO registers access in hwseq layer was creating register conflicts.
[how]
Migrated DIO registers from hwseq to dio component.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Bhuvanachandra Pinninti <bpinnint@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
- Consolidate memory QoS measurement functions into a single interface for
better maintainability and usability.
- Update function naming for improved clarity.
- Unify latency measurements into a single function call with update
programming sequence.
- Add `start_measuring_urgent_assertion_count` and
`get_urgent_assertion_count` interfaces.
- Add `start_measuring_prefetch_data_size` and `get_prefetch_data_size`
interfaces.
- Update start_measuring_unbounded_bandwidth implementation to measure 200
data returns in the middle of prefetch window.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Panel Replay is not an eDP-specific function.
[HOW]
Create new Panel Replay source files and move the Panel Replay
functions from the eDP files to the new files. Additionally, create
a new link_service construct function to assign the related
function pointers.
Reviewed-by: Robin Chen <robin.chen@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Matthew Stewart <matthew.stewart2@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similarly to the analog_engine field, add a new analog_id field
which contains the encoder ID of the analog encoder that
corresponds to the link encoder.
Previously, the default encoder ID of the link encoder was used,
which meant that we passed the wrong ID in case of DVI-I.
Fixes: 5834c33fd3 ("drm/amd/display: Add concept of analog encoders (v2)")
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is no way to check pipe topology update history through a
dump.
[How]
Add a topology history structure to dc with snapshots of the most recent
pipe topology updates.
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Nicholas Carbones <ncarbone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
An invalidation request arriving during prefetch can potentially hang
the system if dynamic clock gating is enabled and memory power requests
are disabled.
[How]
• Disable clock gating and enable memory power requests for the duration
of the prefetch.
• Turn on clock gating and disable memory power requests again after
prefetch is complete.
Limit the scope for DCN35 and DCN42 only.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a num_analog_stream_encoders field to indicate how many
analog stream encoders are present. When analog stream encoders
are present, create them.
Additionally, add an analog_engine field to link encoders and
search for supported analog encoders in the BIOS for each link.
When connecting an RGB signal, search for analog stream encoders.
The actual DCE analog link and stream encoder is going to be
added in a subsequent commit.
v2:
Add check to see if an analog engine is really supported.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are going to support analog encoders as well, not just digital,
so we need to make space for them in various arrays.
v2: Fix typo.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debugging underflow issues frequently requires knowing the
HW state at the time of underflow. To enable capturing this
HW state information, interface functions are needed for the
various DC HW blocks.
[How]
This change adds the interface functions to read HW state for
the following DC HW blocks:
- HUBBUB
- HUBP
- DPP
- MPC
- OPP
- DSC
- OPTC
- DCCG
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Karen Chen <Karen.Chen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dml2 folder contains all logic for all versions of DML2
This is currently DML2.0 and DML2.1.
Rename dml2 to dml2_0 folder to reflect this better (dml2_0
for DML2.0).
[How]
Rename dml2 to dml2_0 folder and update dml2 references to
use dml2_0 folder.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: waynelin <Wayne.Lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
The DCN401 cursor offload path needs to take into account
use_mall_for_cursor, and also need to ensure the dcn32
function assigns the cursor cache fields (DCN401 uses the
dcn32 implementation).
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We require an interlock between driver and firmware for upcoming
features and given that this could possibly happen on any single
cursor programming call (and that we can't asynchronously wait for
firmware to respond because of it) we'd be regressing cursor performance
by at least an extra 40us per call.
When we could possibly have cursor update every 20us - 100s from high
frequency gaming mice this means that we'd be stuttering or dropping
updates and impacting overall cursor performance.
We want a solution that can:
1. Interlock between other firmware features
2. Not stall out or require the DMCUB lock for every single update
[How]
When cursor offloading is enabled and supported by an ASIC driver will
route the cursor programming through to DMU as part of the regular
DC stream cursor programming interfaces for attributes and position.
The atomic pipe programming version will not be updated: this will still
follow the existing programming path by keeping track of a field that
specifies when the register writes should be deferred to DMU.
Cursor locking is not required when cursor offload is in progress since
the updates are consolidated and processed by DMU once at the end
of the frame in a periodic manner.
The shared buffer the firmware queries from is allocated along with the
rest of the scratch state region in an area that's accessible by
both firmware and driver.
The size of the cursor offload (v1) state will not change, but it does
have a unique union per ASIC version with room for expansion if needed.
When firmware features notifying DMU of DRR updates are not enabled we
now send an explicit vtotal min/max update via driver to DMU firmware
whenever the vtotal max changes. This is to allow the cursor programming
to determine the appropriate latch update point offset from vupdate.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Certain OVT timings require DSC configurations which divide the
horizontal active unevenly across DSC slices
-DSC slices must be even, so padding needs to be added to the active
to make this possible
-The pixel clock of the HW now needs to be increased to accommodate
the extra padded pixels
-To keep the line time the same, the blank of the HW timing needs to
be increased as well
[How]
-Calculate h_active padding, h_total padding, and pixel clock based
off of the original OVT timing and DSC calculations
-Store these values in the pipe and program HW with these modifications
-Added general support for cases where DSC slice config does not evenly
split the horizontal active by fixing some slice width calculations
-Updated PPS calculations for these cases
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Header file name "link.h" collides with system header when dc is
compiled as a user-mode library
[WHAT]
Rename link.h to link_service.h to avoid name collision
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bounding box values can be stored in multiple locations. (e.g. PMFW, VBIOS, DMUB).
The source and interpretation of these values can vary with DCN revision
so there should be a component that can gather these values and translate
them accordingly
[How]
Have component start with the statically defined values as a base.
Then update them as needed with DCN-specific logic
Guard this component with FPU flags since values need to be in float point.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HUBP needs to know the size of the lut's destination in MPC.
This is currently defaulted to 17, and needs to be set for specific
lut size.
[how]
Define and apply the missing hubp field. Taking this opportunity
to consolidate the programming of 3dlut into a hubp and mpc function.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function `dp_retrain_link_dp_test` currently allocates a large
audio_output array on the stack, causing the stack frame size to exceed
the compiler limit (1080 bytes > 1024 bytes).
This change prevents stack overflow issues:
amdgpu/../display/dc/link/accessories/link_dp_cts.c:65:13: warning: stack frame size (1080) exceeds limit (1024) in 'dp_retrain_link_dp_test' [-Wframe-larger-than]
static void dp_retrain_link_dp_test(struct dc_link *link,
v2: Move audio-related data like `audio_output` is kept "per pipe" to
manage the audio for that specific display pipeline/display output path
(stream). (Wenjing)
v3: Update in all the places where `build_audio_output` is currently
called with a separate audio_output variable on the stack & wherever
`audio_output` is passed to other functions
`dce110_apply_single_controller_ctx_to_hw()` &
`dce110_setup_audio_dto()` (like `az_configure`, `wall_dto_setup`)
replace with usage of `pipe_ctx->stream_res.audio_output`
to centralize audio data per pipe.
v4: Remove empty lines before `build_audio_output`. (Alex)
Fixes: 9c6669c2e2 ("drm/amd/display: Fix Link Override Sequencing When Switching Between DIO/HPO")
Cc: Wayne Lin <wayne.lin@amd.com>
Cc: George Shen <george.shen@amd.com>
Cc: Michael Strauss <michael.strauss@amd.com>
Cc: Alvin Lee <Alvin.Lee2@amd.com>
Cc: Ray Wu <ray.wu@amd.com>
Cc: Wenjing Liu <wenjing.liu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Tom Chung <chiahsuan.chung@amd.com>
Cc: Roman Li <roman.li@amd.com>
Cc: Alex Hung <alex.hung@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SmartMux is a mechanism to switch the GPU being used for scanout in a
hybrid configuration. This is used for devices with an eDP and two GPUs.
This is only valid when the system has a physical switch (Multiplexer)
in the board to switch between the two GPUs.
When a graphically intensive workload like a game is being run, the
system can be switch the active display to the dGPU, so that we can
avoid copying the buffer from dGPU to APU for scanout. This helps with
latency and FPS. When power consumption is preferred, the system can be
switched to the APU.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC block level should only be responsible for reporting single DSC
instance capabilities. Factoring in ODM combine requirements should be
handled in dc_dsc.c. Both components should acquire clocks from clk_mgr
to determine throughput capabilities instead of relying on hard coded
values as these can differ by SoC and SKU.
[HOW]
1) Add dsc_get_single_enc_caps to acquire single DSC instance
capabilities (replacing dsc_get_enc_caps), factoring in DSCCLK
2) add build_dsc_enc_caps to combine single DSC instance capabilities
3) account for max pixel rate per pipe (DISPCLK) when calculating
minimum slice count
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When performing certain link maintenance compliance tests or forcing link
settings, changing between 128b/132b and 8b/10b rates no longer works on
some ASICs. Some rate divider updates only occur when we set
timings or validate state, which is not performed currently when toggling
DPMS to change rates.
[HOW]
Re-calculate dividers and reprogram audio when switching between DIO
and HPO through DP compliance/escape code path.
Add OTG disable/re-enable so we don't touch the clock while OTG is active.
Acquire dcLock before forcing link settings to avoid thread synchronization
errors due to added programming in escape code path and potential HPD
interrupts.
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Mike Katsnelson <mike.katsnelson@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The tunnel BW validation code has changed to the new one.
Remove the unused code.
The DP tunneling overhead is not updated in SST.
Move updating DP tunneling overhead for both SST and MST.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
