Ensure that the DAC output is enabled at the correct time by
moving it to the DCE link encoder similarly to how digital
outputs are enabled.
This also removes the call to DAC1EncoderControl from the DCE
HWSS, which always felt like it was a hacky solution.
Fixes: 0fbe321a93 ("drm/amd/display: Implement DCE analog link encoders (v2)")
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Tested-by: Mauro Rossi <issor.oruam@gmail.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Spaces before newline are not necessary. Inserting newlines in
multi-line strings are harder to follow when tracing messages.
[How]
Drop extra new lines and split multi-line messages into one print
per line.
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
User may connect mst dock with multi monitors and do quick unplug
and plug in one of the monitor. This operatioin may create CSN from
dock to display driver. Then display driver would disable and then enable
mst link and also disable/enable DPCD mst_en bit in dock RX. However,
when mst_en bit being disabled, if dock has another CSN message to
transmit then the message would be removed because of the disabling of
mst_en. In this case, the message is missing and it ends up no display in
the replugged monitor.
[HOW]
Don't disable mst_en bit when link still has sink connected.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- After the addition of all OVT patches, DSC padding was being accounted
for multiple times, effectively doubling the padding
- This caused compliance failures or corruption
[HOW]
- Add padding to DSC pic width when required by HW, and do not re-add
when calculating reg values
- Do not add padding when computing PPS values, and instead track padding
separately to add when calculating slice width values
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some OLED panels require driver to write Aux BL before link training or
turning on backlight; otherwise monitor brightness will change.
[HOW]
Write the default Vesa Aux backlight control in dmub.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DVI-A & VGA connectors are applicable to DCE ASICs, so move them to
dce110_hwseq.c to block audio sync on SIGNAL_TYPE_RGB for DCE ASICs.
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Analog displays typically have a DDC connection which can be
used by the GPU to read EDID. This commit adds the capability
to probe analog displays using DDC, reading the EDID header and
deciding whether the analog link is connected based on the data
that was read.
Note that VGA has no HPD (hotplug detection), so we need to
to do analog link detection for VGA before checking HPD.
In case of DVI-I, while the connector supports HPD, not all
analog cables connect the HPD pins, so we can't rely on HPD
either.
For reference, see the legacy display code:
amdgpu_connector_vga_detect
amdgpu_display_ddc_probe
DAC load detection will be implemented in a separate commit.
v2:
Fix crash / black screen on newer GPUs during link detection.
Ignore HPD pin for analog connectors.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Analog video signals on VGA or DVI-A (analog part of DVI-I)
don't support audio, so avoid calling any audio related
functions on analog signals.
Stereo sync was not set up for analog signals in the legacy
display code either, so there is no loss of functionality if
we omit it from DC for now.
Also add a dc_is_rgb_signal similar to other dc_is_*_signal.
v2:
Added comment to clarify what we mean by RGB in this context.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-OVT compliance testing for 5120x2880p300Hz YCbCr420 was failing due to
incorrect slice width being calculated
[How]
-Ensure slice width is divisible by 2 for 420 to comply with spec
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Certain OVT timings require DSC configurations which divide the
horizontal active unevenly across DSC slices
-DSC slices must be even, so padding needs to be added to the active
to make this possible
-The pixel clock of the HW now needs to be increased to accommodate
the extra padded pixels
-To keep the line time the same, the blank of the HW timing needs to
be increased as well
[How]
-Calculate h_active padding, h_total padding, and pixel clock based
off of the original OVT timing and DSC calculations
-Store these values in the pipe and program HW with these modifications
-Added general support for cases where DSC slice config does not evenly
split the horizontal active by fixing some slice width calculations
-Updated PPS calculations for these cases
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If symclk RCO is enabled, stream encoder may not be receiving an ungated
clock by the time we attempt to set stream attributes when setting dpms
on. Since the clock is gated, register writes to the stream encoder fail.
[HOW]
Move set_stream_attribute call into enable_stream, just after the point
where symclk32_se is ungated.
Logically there is no need to set stream attributes as early as is
currently done in link_set_dpms_on, so this should have no impact beyond
the RCO fix.
Reviewed-by: Ovidiu (Ovi) Bunea <ovidiu.bunea@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SmartMux is a mechanism to switch the GPU being used for scanout in a
hybrid configuration. This is used for devices with an eDP and two GPUs.
This is only valid when the system has a physical switch (Multiplexer)
in the board to switch between the two GPUs.
When a graphically intensive workload like a game is being run, the
system can be switch the active display to the dGPU, so that we can
avoid copying the buffer from dGPU to APU for scanout. This helps with
latency and FPS. When power consumption is preferred, the system can be
switched to the APU.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The tunnel BW validation code has changed to the new one.
Remove the unused code.
The DP tunneling overhead is not updated in SST.
Move updating DP tunneling overhead for both SST and MST.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Observe that we try to access DPCD 0x600h of disconnected DP ports.
In order not to wasting time on retrying these ports, call
dpcd_write_rx_power_ctrl() after checking its connection status.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
When MST config is unplugged/replugged too quickly, it can potentially
result in a scenario where previous DC state has not been reset before
the HPD link detection sequence begins. In this case, driver will
disable the streams/link prior to re-enabling the link for link
training.
There is a bug in the current logic that does not account for the fact
that current_state can be released and cleared prior to swapping to a
new state (resulting in the pipe_ctx stream pointers to be cleared) in
between disabling streams.
To resolve this, cache the original streams prior to committing any
stream updates.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
The response of DP BW allocation is handled in Outbox ISR.
When it failed to request the DP BW allocation, it sent another
DPCD request in Outbox ISR immediately. The DP AUX reply also
uses the Outbox ISR. So, no AUX reply happened in this case.
Change to use HPD IRQ for the notification.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We see unstable DP LL 4.2.1.3 test result with dpia pre-train. It is
because the outbox interrupt mechanism can not handle HPD
immediately and require some improvement.
[HOW]
1. not enable link if hpd_pending is true.
2. abort pre-train if training failed and hpd_pending is true.
3. check if 2 lane supported when it is alt mode
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The defines have also been updated with prefix AMD_ and atomfirmware.h
has been temporarily updated with both sets of defines to allow the
transition.
This update is being made to standardize workaround chip_cap flags,
in order to support more workaround flags in the future.
[HOW]
Updated EXT_DISPLAY_PATH_CAPS__DP_FIXED_VS_EN define, the flag is now
an enum masked by EXT_DISPLAY_PATH_CAPS__EXT_CHIP_MASK. All checks for
DP_FIXED_VS_EN are now performed by masking with EXT_CHIP_MASK and
checking for an exact match rather than the previous bitwise AND check.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain small HBlank timings may not have a large enough HBlank to
support audio when low bpp DSC is enabled. HBlank expansion by the
source can solve this problem, but requires the branch/sink to support
HBlank reduction.
[How]
Update DPMS sequence to call DM to perform DPCD write to enable HBlank
reduction on the branch/sink. Add stub in dm_helpers to be implemented
later.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We like to have pretrain for dpia link so that dp and dp tunneling
have aligned behavior. The Main difficult for dpia pretrain is that
encoder can not get corresponded dpia port when link detection
in current implementation.
[HOW]
1. create enable/disable dpia output functions for dcn35 encoder
and have dpia_id and other necessary info as inputs.
2. dcn35 dpia use the new functions to enable/disable output.
3. have a option to enable/disable the change.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
OLED power up sequence takes an extra 150ms via hardcoded delay,
but there is a strict requirement on DisplayOn resume time.
For customer panel, remove these delays to meet target until a
cleaner solution is can be put in place.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Supporting UHBR10 link rate on eDP leverages
the existing DP2.0 code but need to add some small
adjustments in code.
[how]
Acknowledge the given DPCD caps for UHBR10
link rate support and allow DP2.0 programming
sequence and link training for eDP.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
In newer DCN's the programming of SYMCLK_FE_SRC_SEL depends on
the value of DIG_FE_SOURCE_SELECT. If DIG_FE_SOURCE_SELECT is not
already programmed at the time of PHY / DIG enable then the FW
sequence will program an incorrect SYMCLK source. Ensure that we
program DIG_FE_SOURCE_SELECT for all DIO scenarios (DVI in this
particular case) before going through the PHY / DIG enable sequence.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In order to support glitchless display clock ramping for virtual stream,
we must
turn on symclk for stream encoder. The code will power on phy and enable
symclk
for dio encoder during virtual stream dpms sequence.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Switching between DSC clock or disable DSC block are not double buffered update.
Corruption is observed if these updates happen before DSC double buffered
disconnection.
[how]
Move DSC disable and refclk reset to post unlock update. Wait for DSC double buffered
disconnection and all mpccs are disconnected before reset DSC clock.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Upon disconnecting a UHBR SST display, the disconnection and the
SetTimings to disable the display can occur such that link_set_dpms_off
occurs after the disconnection has already processed
(link->type is dc_connection_none). Thus, the AUX related
operations should be skipped when clearing the payload allocation table.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
as part of cleanup, need to refactor vpg. It was improperly referenced
as a dcn specfic part of link. the dcn agnostic code needed was ripped out
and put into vpg.h, now in dc/inc/hw.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Enabling higher compiler warning levels results in many issues that can
be trivially resolved as well as some potentially critical issues.
[how]
Fix all compiler warnings found with various compilers and higher
warning levels. Primarily, potentially uninitialized variables and
unreachable code.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When usb4 bandwidth allocation mode is enabled, driver need to request
bandwidth from connection manager. For mst link, the requested
bandwidth should be big enough for all remote streams.
[HOW]
- If mst link, the requested bandwidth should be the sum of all mst
streams bandwidth added with dp MTPH overhead.
- Allocate/deallcate usb4 bandwidth when setting dpms on/off.
- When doing display mode validation, driver also need to consider total
bandwidth of all mst streams for mst link.
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Peichen Huang <peichen.huang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changing PBN calculation to be more in line with spec. We don't need to
inflate PBN_NATIVE value by the 1.006 margin, since that is already
taken care of in the get_pbn_per_slot function.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
