[Why]
DCN 3.6+ hardware supports CRC-32 polynomial in addition to the
legacy CRC-16. Enable 32-bit CRC values per color component for
improvement of precision in display validation.
[How]
When userspace sets crc_poly_mode (0=CRC-16, 1=CRC-32) via the debugfs
interface, the value is stored in dm_irq_params.crc_poly_mode. When CRC
source configuration triggers amdgpu_dm_crtc_configure_crc_source(),
crc_poly_mode is retrieved from dm_irq_params and passed to
dc_stream_configure_crc().
In the DC layer, dc_stream_configure_crc() sets crc_poly_mode into the
crc_params structure and passes it to optc35_configure_crc(). If the
hardware supports the OTG_CRC_POLY_SEL register, the register is
programmed to select CRC-16 or CRC-32 polynomial.
When reading CRC values, optc35_get_crc() checks whether CRC32 register
masks are available. If present, it reads 32-bit CRC values from
OTG_CRC0/1_DATA_R32/G32/B32 registers; otherwise, it falls back
to reading 16-bit CRC values from legacy OTG_CRC0/1_DATA_RG/B
registers.
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Debugging underflow issues frequently requires knowing the
HW state at the time of underflow. To enable capturing this
HW state information, interface functions are needed for the
various DC HW blocks.
[How]
This change adds the interface functions to read HW state for
the following DC HW blocks:
- HUBBUB
- HUBP
- DPP
- MPC
- OPP
- DSC
- OPTC
- DCCG
Reviewed-by: George Shen <george.shen@amd.com>
Signed-off-by: Karen Chen <Karen.Chen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Knowing the destination of OTG's vertical interrupt 2 is useful for
debugging, but it is not currently included in the OTG state readback
logic
[How]
Read the OTG interrupt destination register to get the vertical interrupt
2 destination on ASICs that have this register when reading back the OTG
state from hardware
Reviewed-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Have the need to specify the CRC window on specific CRC engine.
dc_stream_configure_crc() today calculates CRC on crc engine 0 only and always
resets CRC engine at first.
[How]
Add index parameter to dc_stream_configure_crc() for selecting the desired crc
engine. Additionally, add another parameter to specify whether to skip the
default reset of crc engine.
Reviewed-by: HaoPing Liu <haoping.liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a few cleanup and refactoring tasks that need to be done
with the DML2.1 wrapper and DC interface to remove dependencies on
legacy structures and N-1 prototypes.
[How]
Implemented pipe_ctx->global_sync.
Implemented new functions to use pipe_ctx->hubp_regs and
pipe_ctx->global_sync:
- hubp_setup2
- hubp_setup_interdependent2
- Several other new functions for DCN 4.01 to support newer structures
Removed dml21_update_pipe_ctx_dchub_regs
Removed dml21_extract_legacy_watermark_set
Removed dml21_populate_pipe_ctx_dlg_param
Removed outdated dcn references in DML2.1 wrapper.
Reviewed-by: Austin Zheng <austin.zheng@amd.com>
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Since now we can set multiple crc windows for secure display, add a new input
parameter for dc_stream_get_crc to indicate to fetch crc from which crc
engine.
Reviewed-by: HaoPing Liu <haoping.liu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Before every full update we must wait for all pending updates to be
cleared - this is particularly important for minimal transitions
because if we don't wait for pending cleared, it will be as if
there was no minimal transition at all. In OTG we must read 3 different
status registers for pending cleared, one specifically for OTG updates,
one specifically for OPTC updates, and the last for surface related
updates.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
OTG has new functionality to allow P-State relative to VStartup. Keepout region
for this should be configured based on DML outputs same as other global sync
params.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The values calculated in optc1_get_otg_active_size are assigned to the
wrong output parameters, vertical blank is being used for horizontal size
and vice versa. This results in DPG test pattern looking wrong during
hardware init, as the DPG dimensions get assigned from this output, and
potentially other issues.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN10 OPTC is used by other DCNs, and in some cases it might be useful
to have V_TOTAL_REGS available. This commit add V_TOTAL_REGS as part of
the TG field.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Add extra logging for DCSURF_FLIP_CNTL, DCHUBP_CNTL,
OTG_MASTER_EN, and OTG_DOUBLE_BUFFER_CONTROL for more
debuggability for a system crash.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to support low hz case, but the original
vtotal/vtotal_min/vtotal_max can't support more
than 0x7FFF.
[HOW]
We use the 2 HW reg to contorl long vblank case.
1. OTG_V_COUNT_STOP_CONTROL -> vcount_stop
2. OTG_V_COUNT_STOP_CONTROL2 -> vcount_stop_timer
vcount_stop define from which line we stop using vcount
and start using vcount2.
vcount_stop_timer define how long we use vcount2.
Ex:
Vtotal = 7
OTG_V_COUNT_STOP_CONTROL = 4
OTG_V_COUNT_STOP_CONTROL2 = 5
time : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11
vcount : 0, 1, 2, 3, - - - - - 4, 5, 6
vcount2 : 0, 1, 2, 3, 4,
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Signed-off-by: Robin Chen<robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Odm update is doubled buffered. We need to wait for ODM update to be
completed before optimizing bandwidth or programming new udpates.
[HOW]
implement wait_for_odm_update_pending_complete function to wait for:
1. odm configuration update is no longer pending in timing generator.
2. no pending dpg pattern update for each active OPP.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move all optc files to unique
folder optc.
[how]
creating optc repo in dc, and moved the dcnxx_optc.c and .h files into
corresponding new folders inside the optc and cleared the linkage
errors by adding relative paths in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Parandhaman K <parandhaman.k@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
