Use intel_dp_effective_data_rate() to calculate the required link BW for
eDP, DP-SST and MST links. This ensures that the BW is calculated the
same way for all DP output types, during mode validation as well as
during state computation. This approach also allows for accounting with
BW overheads due to the SSC, DSC, FEC being enabled on a link, as well
as due to the MST symbol alignment on the link. Accounting for these
overheads will be added by follow-up changes.
This way also computes the stream BW on a UHBR link correctly, using the
corresponding symbol size to effective data size ratio (i.e. ~97% link
BW utilization for UHBR vs. only ~80% for non-UHBR).
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20251215192357.172201-9-imre.deak@intel.com
The remaining utils display needs from i915_utils.h are primarily
MISSING_CASE() and fetch_and_zero(), with a couple of
i915_inject_probe_failure() uses.
To avoid excessive churn, add duplicates of MISSING_CASE() and
fetch_and_zero() to intel_display_utils.h, and switch display to use the
display utils.
As long as there are display files that include i915_drv.h, which
includes i915_utils.h, we'll need #ifndef guards for MISSING_CASE() and
fetch_and_zero() in both utils headers. We can remove them once display
no longer depends on i915_drv.h.
A couple of files in display still need i915_utils.h for
i915_inject_probe_failure(). Annotate this. They will be handled
separately.
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patch.msgid.link/79f9e31ca64c8c045834d48e20ceb0c515d1e9e1.1761146196.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The Fixed: commit below overlooked the fact that
intel_dp_link_train_all_phys() is only used for non-UHBR link rates, but
intel_dp_stop_link_train() is used for both non-UHBR and UHBR link
rates. Hence, after removing the disabling of the training pattern from
intel_dp_stop_link_train(), the commit missed adding this back to the
end of UHBR link training in intel_dp_128b132b_link_train(). This left
the sink in link training mode at the end of an UHBR rate link training.
Fix things by disabling the training pattern at the end of UHBR link
training as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 11fab5a2a1 ("drm/i915/dp: Clear DPCD training pattern before transmitting the idle pattern")
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://lore.kernel.org/r/20250724182900.160891-1-imre.deak@intel.com
We are supposed to switch off the training pattern in DPCD before
we start transmitting the idle pattern. For LTTPRs we do that
correctly, but for the sink DPRX we only do this correctly
for some platforms.
On pre-HSW (where we don't implement the .set_idle_link_train()
hook), we directly switch from transmitting the training pattern
to normal pixel transmission (the hardware should hopefully
guarantee that the minimum number of required idle patters will
be transmitted during this transition). The DPCD write correctly
precedes the actual switch away from the training pattern.
For HSW+ we start transmitting the idle pattern earlier, and only
switch off the DPCD training pattern after we switch from the idle
pattern to normal pixel transmission. Adjust the code to disable
the DPCD training pattern before we start transmitting the idle
pattern.
v2: Tweak the commit message a bit
Tested-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250710201718.25310-4-ville.syrjala@linux.intel.com
Cross-subsystem Changes:
- Update GVT MAINTAINERS (Jani)
Driver Changes:
- Updates for xe3lpd display (Gustavo)
- Fix link training interrupted by HPD pulse (Imre)
- Watermark bound checks for DSC (Ankit)
- VRR Refactor and other fixes and improvements (Ankit)
- More conversions towards intel_display struct (Gustavo, Jani)
- Other clean-up patches towards a display separation (Jani)
- Maintain asciibetical order for HAS_* macros (Ankit)
- Fixes around probe/initialization (Janusz)
- Fix build and doc build issue (Yue, Rodrigo)
- DSI related fixes (Suraj, William, Jani)
- Improve DC6 entry counter (Mohammed)
- Fix xe2hpd memory type identification (Vivek)
- PSR related fixes and improvements (Animesh, Jouni)
- DP MST related fixes and improvements (Imre)
- Fix scanline_offset for LNL+/BMG+ (Ville)
- Some gvt related fixes and changes (Ville, Jani)
- Some PLL code adjustment (Ville)
- Display wa addition (Vinod)
- DRAM type logging (Lucas)
- Pimp the initial FB readout (Ville)
- Some sagv/bw cleanup (Ville)
- Remove i915_display_capabilities debugfs entry (Jani)
- Move PCH type to display caps debugfs entry (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/Z_kTqPX5Mjruq1pL@intel.com
MSA Ignore Timing PAR enable is set in the DP sink when we enable variable
refresh rate.
Currently for link training we depend on flipline to decide whether we
want to ignore the msa timings. With fixed refresh rate we will still
fill the flipline in all cases whether panel supports VRR or not.
Change the condition for link training to ignore the msa timings if
vrr.in_range.
v2: Add more documentation and a #TODO for readout of vrr.in_range.
(Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250311093751.1329043-9-ankit.k.nautiyal@intel.com
After link training - both in case of a passing and failing LT result -
a work is scheduled to check the link state. This check should take
place after the link training is completed by disabling the link
training pattern and setting intel_dp::link_trained=true. Atm, the work
is scheduled before these steps, which may result in checking the link
state too early (and thus not retraining the link as expected).
Fix the above by scheduling the link check work after link training is
complete.
v2:
- Add MAX_SEQ_TRAIN_FAILURES instead of open-coding it. (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250305114820.3523077-2-imre.deak@intel.com
During Display Port link training the handling of HPD pulses should be
prevented, as that handling can interfere with the link training:
- Accessing DPCD registers outside the range of link training registers
are not allowed by the Standard (see DP Standard v2.1, 3.5.2.16.1,
3.6.6.1). The pulse handler reads the DPRX capability registers, which
are outside of the allowed range.
- Switching of the LTTPR transparent/non-transparent mode may reset the
LTTPRs on the link, thus aborting any ongoing link training. The pulse
handler does set the LTTPR mode, thus it could unexpectedly abort the
ongoing link training.
Block/unblock the HPD pulse handling for the duration of the link
training to prevent the above DPCD register accesses / LTTPR mode
change.
Apart from the above scenarios, there are other ways a non-link training
DPCD register could be accessed during link training: via the DRM AUX
device node, or via DPCD register probing (as performed by
drm_dp_dpcd_probe()). These will be addressed by a follow-up change.
v2: Rebase on the intel_hpd_suspend/resume -> intel_hpd_block/unblock()
rename change.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250304152917.3407080-5-imre.deak@intel.com
drm/i915 feature pull for v6.15:
Features and functionality:
- Enable DP 128b/132b SST DSC (Jani, Imre)
- Allow DSB to perform commits when VRR is enabled (Ville)
- Compute HDMI PLLs for SNPS/C10 PHYs for rates not in fixed tables (Ankit)
- Allow DSB usage when PSR is enabled on LNL+ (Jouni)
- Enable Panel Replay mode change without full modeset (Jouni)
- Enable async flips with compressed buffers on ICL+ (Ville)
- Support luminance based brightness control via DPCD for eDP (Suraj)
- Enable VRR enable/disable without full modeset (Mitul, Ankit)
- Add debugfs facility for force testing HDCP 1.4 (Suraj)
- Add scaler tracepoints, improve plane tracepoints (Ville)
- Improve DMC wakelock debugging facilities (Gustavo)
- Allow GuC SLPC default strategies on MTL+ for performance (Rodrigo)
- Provide more information on display faults (Ville)
Refactoring and cleanups:
- Continue conversions to struct intel_display (Ville, Jani, Suraj, Imre)
- Joiner and Y plane reorganization (Ville)
- Move HDCP debugfs to intel_hdcp.c (Jani)
- Clean up and unify LSPCON interfaces (Jani)
- Move code out of intel_display.c to reduce its size (Ville)
- Clean up and simplify DDI port enabling/disabling (Imre)
- Make LPT LP a dedicated PCH type, refactor (Jani)
- Simplify DSC range BPG offset calculation (Ankit)
- Scaler cleanups (Ville)
- Remove unused code from GVT (David Alan Gilbert)
- Improve plane debugging (Ville)
- DSB and VRR refactoring (Ville)
Fixes:
- Check if vblank is sufficient for DSC prefill and scaler (Mitul)
- Fix Mesa clear color alignment regression (Ville)
- Add missing TC DP PHY lane stagger delay (Imre)
- Fix DSB + VRR usage for PTL+ (Ville)
- Improve robustness of display VT-d workarounds (Ville)
- Fix platforms for dbuf tracker state service programming (Ravi)
- Fix DMC wakelock support conditions (Gustavo)
- Amend DMC wakelock register ranges (Gustavo)
- Disable the Common Primary Timing Generator (CMTG) (Gustavo)
- Enable C20 PHY SSC (Suraj)
- Add workaround for DKL PHY DP mode write (Nemesa)
- Fix build warnings on clamp() usage (Guenter Roeck, Ankit)
- Fix error handling while adding a connector (Imre)
- Avoid full modeset at probe on vblank delay mismatches (Ville)
- Fix encoder HDMI check for HDCP line rekeying (Suraj)
- Fix HDCP repeater authentication during topology change (Suraj)
- Handle display PHY power state reset for power savings (Mika)
- Fix typos all over the place (Nitin)
- Update HDMI TMDS C20 parameters for various platforms (Dnyaneshwar)
- Guarantee a minimum hblank time for 128b/132b and 8b/10b MST (Arun, Imre)
- Do not hardcode LSPCON settle timeout (Giedrius Statkevičius)
Xe driver changes:
- Re-use display vmas when possible (Maarten)
- Remove double pageflip (Maarten)
- Enable DP tunneling (Imre)
- Separate i915 and xe tracepoints (Ville)
DRM core changes:
- Increase DPCD eDP display control CAP size to 5 bytes (Suraj)
- Add DPCD eDP version 1.5 definition (Suraj)
- Add timeout parameter to drm_lspcon_set_mode() (Giedrius Statkevičius)
Merges:
- Backmerge drm-next (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87h64j7b7n.fsf@intel.com
LTTPRs operating modes are defined by the DisplayPort standard and the
generic framework now provides a helper to switch between them, which
is handling the explicit disabling of non-transparent mode and its
disable->enable sequence mentioned in the DP Standard v2.0 section
3.6.6.1.
So use the new drm generic helper instead as it makes the code a bit
cleaner. Since the driver specific implementation holds the
lttrp_common_caps, if the call to the drm generic helper fails, the
lttrp_common_caps need to be updated as the helper has already rolled
back to transparent mode.
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250203-drm-dp-msm-add-lttpr-transparent-mode-set-v5-3-c865d0e56d6e@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
At the end of a 128b/132b link training sequence, the HW expects the
transcoder training pattern to be set to TPS2 and from that to normal
mode (disabling the training pattern). Transitioning from TPS1 directly
to normal mode leaves the transcoder in a stuck state, resulting in
page-flip timeouts later in the modeset sequence.
Atm, in case of a failure during link training, the transcoder may be
still set to output the TPS1 pattern. Later the transcoder is then set
from TPS1 directly to normal mode in intel_dp_stop_link_train(), leading
to modeset failures later as described above. Fix this by setting the
training patter to TPS2, if the link training failed at any point.
The clue in the specification about the above HW behavior is the
explicit mention that TPS2 must be set after the link training sequence
(and there isn't a similar requirement specified for the 8b/10b link
training), see the Bspec links below.
v2: Add bspec aspect/link to the commit log. (Jani)
Bspec: 54128, 65448, 68849
Cc: stable@vger.kernel.org # v5.18+
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 8b4bbaf8dd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
At the end of a 128b/132b link training sequence, the HW expects the
transcoder training pattern to be set to TPS2 and from that to normal
mode (disabling the training pattern). Transitioning from TPS1 directly
to normal mode leaves the transcoder in a stuck state, resulting in
page-flip timeouts later in the modeset sequence.
Atm, in case of a failure during link training, the transcoder may be
still set to output the TPS1 pattern. Later the transcoder is then set
from TPS1 directly to normal mode in intel_dp_stop_link_train(), leading
to modeset failures later as described above. Fix this by setting the
training patter to TPS2, if the link training failed at any point.
The clue in the specification about the above HW behavior is the
explicit mention that TPS2 must be set after the link training sequence
(and there isn't a similar requirement specified for the 8b/10b link
training), see the Bspec links below.
v2: Add bspec aspect/link to the commit log. (Jani)
Bspec: 54128, 65448, 68849
Cc: stable@vger.kernel.org # v5.18+
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217223828.1166093-2-imre.deak@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Use a forward declaration for struct cec_notifier instead of including
media/cec-notifier.h in intel_display_types.h, and only include it where
needed.
Also realize that a lot of places depend on including linux/debugfs.h
via intel_display_types.h -> media/cec-notifier.h -> media/cec.h, and
include that too where needed.
v2: hsw_ips.c also needs debugfs.h (kernel test robot)
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240827104521.4151471-1-jani.nikula@intel.com
On MST links - at least for some MST branch devices - the list of modes
returned to users on an enabled link depends on the current link
rate/lane count parameters (besides the DPRX link capabilities, any MST
branch BW limit and the maximum link parameters reduced after LT
failures). In particular the MST branch BW limit may depend on the link
rate/lane count parameters programmed to DPCD. After an LT failure and
limiting the maximum link parameters accordingly, users should see a
mode list reflecting these new limits. However with the current fallback
order this isn't ensured, as the new limit could allow for modes
requiring a higher link BW, but these modes will be filtered out due to
the enabled link's lower link BW.
Ensure that the mode list changes in a consistent way after a link
training failure and reducing the link parameters by changing the
fallback order on MST links to happen in BW order.
v2:
- s/INTEL_DP_MAX_SUPPORTED_LANE_COUNTS/INTEL_DP_MAX_SUPPORTED_LANE_CONFIGS
and s/num_common_lane_counts/num_common_lane_configs to make the
difference wrt. max lane counts clearer. (Suraj)
- Add a TODO comment to make the SST fallback logic work the same way as
MST. (Arun)
- Use sort_r()'s default swap function instead of a custom one.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729144458.2763667-1-imre.deak@intel.com
Add connector debugfs entries to force the link rate/lane count to be
used by a link training afterwards. These settings will be clamped to
the supported, i.e. the source's and sink's common rate/lane count.
After forcing the link rate/lane count reset the link training
parameters and for a non-auto setting disable reducing the link
parameters via the fallback logic. The former one can be used after
testing link training failure scenarios - via debugfs entries added
later - to reset the reduced link parameters after the test.
v2:
- Add the entries from intel_dp_link_training.c (Jani)
- Rename the entries to i915_dp_set_link_rate/lane_count.
v3: (Ville)
- Rename the entries/struct fields to force_link_rate/lane_count.
- Lock connection_mutex only for the required intel_dp state.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-18-imre.deak@intel.com
After a link training failure if the link parameters can't be further
reduced, there is no point in trying to retrain the link in the driver.
This avoids excessive retrain attempts after detecting a bad link, for
instance while handling MST HPD IRQs, which is likely redundant as the
link training failed already twice with the same minimum link
parameters. Userspace can still try to retrain the link with these
parameters via a modeset.
While at it make the error message more accurate.
v2: Move converting the error to a debug message to the relevant
follow-up patch. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240610164933.2947366-15-imre.deak@intel.com
