The intel_port_to_tc() call in mtl_port_to_pll_id() assumed that all
TypeC DDI ports are connected to a TypeC PHY. This is not true on BMG
where all the ports - including the PORT_TC1..4 TypeC DDI ports - are
connected to a non-TypeC PHY. For these ports intel_port_to_tc()
returns TC_PORT_NONE, which results in an incorrect port -> PLL ID
mapping. Fix this up by using the expected PORT_TC1..4 port ->
TC_PORT_1..4 tc_port mapping on BMG as well.
Fixes: ca1eda5cd4 ("drm/i915/cx0: Add MTL+ .get_dplls hook")
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patch.msgid.link/20251120172358.1282765-1-imre.deak@intel.com
MTL+ platforms are supported by dpll framework remove a separate
check for hw comparison and rely solely on dpll framework
hw comparison.
Finally, all required hooks are now in place so initialize
PLL manager for MTL+ platforms and remove the redirections
to the legacy code paths from the following interfaces:
* intel_encoder::clock_enable/disable()
* intel_encoder::get_config()
* intel_dpll_funcs::get_hw_state()
* intel_ddi_update_active_dpll()
* pipe_config_pll_mismatch()
v2: Rebase on !HAS_LT_PHY check in intel_ddi_update_active_dpll()
v3: Rebase on !display->dpll.mgr check in intel_ddi_update_active_dpll()
Add check for NVL as the platform is not part of pll framework (Suraj)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20251118132859.2584452-1-mika.kahola@intel.com
Add the PLL hooks for the TBT PLL on MTL+. These are simple stubs
similarly to the TBT PLL on earlier platforms, since this PLL is always
on from the display POV - so no PLL enable/disable programming is
required as opposed to the non-TBT PLLs - and the clocks for different
link rates are enabled/disabled at a different level, via the
intel_encoder::enable_clock()/disable_clock() interface.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20251117104602.2363671-32-mika.kahola@intel.com
Add .get_dplls function pointer for MTL+ platforms
to support dpll framework. Reuse the ICL function
pointer.
v2: Getting configuration either for a C10 or on the PTL port B
eDP on TypeC PHY case for a C20 PHY PLL. Hence refer to this
case as "non_tc_phy" instead of "c10phy".
v3: Fix comment to "eDP over TypeC" (Suraj)
Fix pll id as separate variable (Suraj)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20251117104602.2363671-20-mika.kahola@intel.com
To bring MTL+ platform aligned call and calculate PLL state
from dpll framework.
v2: Rename mtl_compute_c10phy_dpll() to mtl_compute_non_tc_phy_dpll().
The state is computed either for a C10 or on the PTL port B eDP
over TypeC PHY case for a C20 PHY PLL. Hence refer to this case as
"non_tc_phy" instead of "c10phy".
Rename mtl_compute_c20phy_dplls() to mtl_compute_tc_phy_dplls() for
symmetry with mtl_compute_non_tc_phy_dpll().
v3: Reword commit message (Suraj)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://lore.kernel.org/r/20251117104602.2363671-19-mika.kahola@intel.com
Convert some of the intel_de_wait_custom() users over to
intel_de_wait_us(). We'll eventually want to eliminate
intel_de_wait_custom() as it's a hinderance towards using
poll_timeout_us().
This includes all the obvious cases where we only specify
a microsecond timeout to intel_de_wait_custom().
Done with cocci (with manual formatting fixes):
@@
expression display, reg, mask, value, timeout_us, out_value;
@@
- intel_de_wait_custom(display, reg, mask, value, timeout_us, 0, out_value)
+ intel_de_wait_us(display, reg, mask, value, timeout_us, out_value)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251110172756.2132-6-ville.syrjala@linux.intel.com
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
intel_de_wait*() take the timeout in milliseconds. Include
that information in the function name to make life less
confusing. I'll also be introducing microsecond variants
of these later.
Done with cocci:
@@
@@
(
static int
- intel_de_wait
+ intel_de_wait_ms
(...)
{
...
}
|
static int
- intel_de_wait_fw
+ intel_de_wait_fw_ms
(...)
{
...
}
|
static int
- intel_de_wait_for_set
+ intel_de_wait_for_set_ms
(...)
{
...
}
|
static int
- intel_de_wait_for_clear
+ intel_de_wait_for_clear_ms
(...)
{
...
}
)
@@
@@
(
- intel_de_wait
+ intel_de_wait_ms
|
- intel_de_wait_fw
+ intel_de_wait_fw_ms
|
- intel_de_wait_for_set
+ intel_de_wait_for_set_ms
|
- intel_de_wait_for_clear
+ intel_de_wait_for_clear_ms
)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patch.msgid.link/20251110172756.2132-4-ville.syrjala@linux.intel.com
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
The remaining utils display needs from i915_utils.h are primarily
MISSING_CASE() and fetch_and_zero(), with a couple of
i915_inject_probe_failure() uses.
To avoid excessive churn, add duplicates of MISSING_CASE() and
fetch_and_zero() to intel_display_utils.h, and switch display to use the
display utils.
As long as there are display files that include i915_drv.h, which
includes i915_utils.h, we'll need #ifndef guards for MISSING_CASE() and
fetch_and_zero() in both utils headers. We can remove them once display
no longer depends on i915_drv.h.
A couple of files in display still need i915_utils.h for
i915_inject_probe_failure(). Annotate this. They will be handled
separately.
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patch.msgid.link/79f9e31ca64c8c045834d48e20ceb0c515d1e9e1.1761146196.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a scripted split of the display related register macros from
i915_reg.h to display/intel_display_regs.h. As a starting point, move
all the macros that are only used in display code (or GVT). If there are
users in core i915 code or soc/, or no users anywhere, keep the macros
in i915_reg.h. This is done in groups of macros separated by blank
lines, moving the comments along with the groups.
Some manually picked macro groups are kept/moved regardless of the
heuristics above.
This is obviously a very crude approach. It's not perfect. But there are
4.2k lines in i915_reg.h, and its refactoring has ground to a halt. This
is the big hammer that splits the file to two, and enables further
cleanup.
Cc: Suraj Kandpal <suraj.kandpal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com> # v2
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250606102256.2080073-1-jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Rename intel_shared_dpll to intel_dpll to represent both
shared and individual dplls. Since from MTL each PHY has it's
own PLL making the shared PLL naming a little outdated. In an
effort to make this framework accepting of future changes this
needs to be done.
--v2
-Use intel_dpll_global to make sure names start with the filename
[Jani/Ville]
-Explain the need of this rename [Jani]
--v3
-Just keep it intel_dpll [Jani]
--v4
-Fix comment [Jani]
-Use just num_dpll and dplls [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250515071801.2221120-7-suraj.kandpal@intel.com
Rename intel_shared_dpll_funcs to intel_dpll_funcs
since it needs to represent both shared and individual
dplls.
--v2
-Change intel_global_dpll to intel_dpll_global to be more
in line with the naming standard where the name should
start with the file name [Jani]
--v3
-Drop shared and global altogether [Jani]
--v4
-Keep declarations sorted [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250515071801.2221120-6-suraj.kandpal@intel.com
Now that INTEL_PCH_TYPE() and HAS_PCH_*() macros are under display, and
accept a struct intel_display pointer, use that instead of struct
drm_i915_private pointer in display code.
This is done naively by running:
$ sed -i 's/\(INTEL_PCH_TYPE\|HAS_PCH_[A-Z0-9_-]*\)([^)]*)/\1(display)/g' \
$(find drivers/gpu/drm/i915/display -name "*.c")
and fixing the fallout, i.e. removing unused local i915 variables and
adding display variables where needed.
v2: Rebase
Reviewed-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Link: https://lore.kernel.org/r/999f4d7b8ed11739b1c5ec8d6408fc39d5e3776b.1744880985.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we loop over all joined pipes and enable/disable the
shared dplls for each. We don't really have to do that since
all joined pipes will be using the same dpll. So let's just do
the enable/disable once for the whole set of joined pipes.
We can still keep tracking the dpll active set as pipes as long
as we remember to flip the bits for all the joined pipes on one go.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250310183528.3203-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The dedicated display PHYs reset to a power state that blocks S0ix,
increasing idle system power. After a system reset (cold boot,
S3/4/5, warm reset) if a dedicated PHY is not being brought up
shortly, use these steps to move the PHY to the lowest power state
to save power.
1. Follow the PLL Enable Sequence, using any valid frequency such
as DP 1.62 GHz. This brings lanes out of reset and enables the
PLL to allow powerdown to be moved to the Disable state.
2. Follow PLL Disable Sequence. This moves powerdown to the Disable
state and disables the PLL.
v2: Rename WA function to more descriptive (Jani)
For PTL, only port A needs this wa
Add helpers to check presence of C10 phy and pll enabling (Imre)
v3: Rename wa function (Imre)
Check return value of C10 pll tables readout (Imre)
Use PLL request to check pll enabling (Imre)
v4: Move intel_cx0_pll_is_enabled() right after
intel_cx0_pll_disable() (Imre)
Add drm_WARN_ON() if C10 state cannot be calculated from
the tables (Imre)
v5: Add debug message on PLL enabling (Imre)
Add check for intel_encoder_is_dig_port() (Imre)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250218100019.740556-3-mika.kahola@intel.com
Use intel_display as an argument for intel_shared_dpll_init() and
replace drm_i915_private in function wherever possible.
While at it prefer using display->platform.xx over IS_PLATFORM.
Initialize dpio_phy and dpio_channel since with IS_GEMINILAKE()
and IS_BROXTON() compiler knows it will return false for xe but
since display->platform.xx is a runtime check which means the
compiler sees a potential path where uninitialized variables
could be accessed and raises a warning.
--v2
-Amend commit message to explain why some variables were
initialized [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250212074542.3569452-8-suraj.kandpal@intel.com
