Track dc balance flip count with params per crtc. Increment
DC Balance Flip count before every flip to indicate DMC
firmware about new flip occurrence which needs to be adjusted
for dc balancing. This is tracked separately from legacy
FLIP_COUNT register also Reset DC balance flip count value
while disabling VRR adaptive mode, this is to start with
fresh counts when VRR adaptive refresh mode is triggered again.
--v2:
- Call during intel_update_crtc.(Ankit)
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patch.msgid.link/20251223104542.2688548-11-mitulkumar.ajitkumar.golani@intel.com
The helper intel_vrr_compute_config_late() practically just computes the
guardband. Rename intel_vrr_compute_config_late() to
intel_vrr_compute_guardband().
Since we are going to compute the guardband and then move the
vblank_start for optmizing guardband move it to
intel_crtc_compute_config() which handles such changes.
v2: Move the function at the last after clocks, pipe_mode etc. are all
set. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20251016055415.2101347-4-ankit.k.nautiyal@intel.com
The helper intel_vrr_vblank_delay() was used to keep track of the SCL
lines + the extra vblank delay required for ICL/TGL.
This was used to wait for sufficient lines for:
-push send bit to clear for VRR case
-evasion to delay the commit.
For first case we are using safe window scanline wait and with that we
just need to wait for SCL lines, we do not need to wait for the extra
vblank delay required for ICL/TGL. For the second case, we actually
do not need to wait for extra lines before the undelayed vblank, if we
are already in the safe window.
To sum up, SCL lines is sufficient for both cases.
So drop the helper intel_vrr_vblank_delay and just use
crtc_state->set_context_latency instead.
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-10-ankit.k.nautiyal@intel.com
Until LNL, intel_dsb_wait_vblanks() used to wait for the undelayed vblank
start. However, from PTL onwards, it waits for the start of the
safe-window defined by the number of lines programmed in the register
TRANS_SET_CONTEXT_LATENCY. This change was introduced to move the SCL
window out of the vblank region, supporting modes with higher refresh
rates and smaller vblanks. This change introduces a "safe window" a
scanline range from (undelayed vblank - SCL) to (delayed vblank - SCL).
As a result, on PTL+ platforms, the DSB wait for vblank completes exactly
SCL lines earlier than the undelayed vblank start (safe window start).
If the flip occurs in the active region and the push happens before the
vmin decision boundary, the DSB wait fires early, and the push is sent
inside this safe window. In such cases, the push bit is cleared at the
delayed vblank, but our wait logic does not account for the early trigger,
leading to DSB poll errors.
To fix this, we add an explicit wait for the end of the safe window i.e.,
the scanline range from (undelayed vblank - SCL) to (delayed vblank - SCL).
Once past this window, we are exactly SCL lines away from the delayed
vblank, and our existing wait logic works as intended.
This additional wait is only effective if the push occurs before the vmin
decision boundary. If the push happens after the boundary, the hardware
already guarantees we're SCL lines away from the delayed vblank, and the
extra wait becomes a no-op.
v2:
- Use helpers for safe window start/end. (Ville)
- Move the extra wait inside the helper to wait for delayed vblank. (Ville)
- Update the commit message.
v3:
- Add more documentation for explanation for the wait. (Ville)
- Rename intel_vrr_vmin_safe_window_start/end as this is vmin safe
window. (Ville)
- Minor refactoring to align with the code. (Ville)
- Update the commit message for more clarity.
v4:
- Retain name for intel_vrr_safe_window_start as it doesn't change with
vmin/vmax etc. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250924141542.3122126-7-ankit.k.nautiyal@intel.com
Since the vrr.guardband can now change for platforms that always use the
VRR Timing Generator, and it is unsafe to reprogram the guardband on the
fly, move the guardband and pipeline_full checks from the pure !fastboot
path and add a check for intel_vrr_always_use_vrr_tg().
For older platforms the vrr.guardband change happens when VRR Timing
generator is off. For the platforms that always use the VRR Timing
Generator, this will prevent reprogramming the vrr.guardband without a
full modeset. However, this will disrupt LRR functionality for these
platforms.
v2: Modify the check to avoid breaking the LRR on older platform.
(Ville)
v3: Correct the oversight of not removing the lines from the original
location. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250324133248.4071909-12-ankit.k.nautiyal@intel.com
During modeset enable sequence, program the fixed timings, and turn on the
VRR Timing Generator (VRR TG) for platforms that always use VRR TG.
For this intel_vrr_set_transcoder now always programs fixed timings.
Later if vrr timings are required, vrr_enable() will switch
to the real VRR timings.
For platforms that will always use VRR TG, the VRR_CTL Enable bit is set
and reset in the transcoder enable/disable path.
v2: Update intel_vrr_set_transcoder_timings for fixed_rr.
v3: Update intel_set_transcoder_timings_lrr for fixed_rr. (Ville)
v4: Have separate functions to enable/disable VRR CTL
v5:
-For platforms that do not always have VRRTG on, do write bits other
than enable bit and also use write the TRANS_VRR_PUSH register. (Ville)
-Avoid writing trans_ctl_vrr if !vrr_possible().
v6:
-Disable VRR just before intel_ddi_disable_transcoder_func(). (Ville)
-Correct the sequence of configuring PUSH and VRR Enable/Disable. (Ville)
v7: Reset trans_vrr_ctl to 0 unconditionally in
intel_vrr_transcoder_disable(). (Ville)
v8: Reset trans_vrr_ctl if flipline is not set. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://lore.kernel.org/r/20250324133248.4071909-9-ankit.k.nautiyal@intel.com
Since we don't do mailbox updates the push send bit
should alwyas clear by the time the delay vblank fires
and the flip completes. Check for that to make sure we
haven't screwed up the sequencing/vblank evasion/etc.
On the DSB path we should be able to guarantee this
since we don't have to deal with any scheduler latencies
and whatnot. I suppose unexpected DMA/memory latencies
might be the only thing that might trip us up here.
For the MMIO path we do always have a non-zero chance
that vblank evasion fails (since we can't really guarantee
anything about the scheduling behaviour). That could trip
up this check, but that seems fine since we already print
errors for other types of vblank evasion failures.
Should the CPU vblank evasion actually fail, then the push
send bit can still be set when the next commit happens. But
both the DSB and MMIO paths should handle that situation
gracefully.
v2: Only check once instead of polling for two scanlines
since we should now be guaranteed to be past the
delayed vblank.
Also check in the MMIO path for good measure
v3: Skip the push send check when VRR is disabled.
With joiner the secondary pipe's DSBs doen't have access
to the transcoder registers, and so doing this check
there triggers a reponse timeout error on the DSB. VRR
is not currently allowed when using joiner, so this will
prevent the bogus register access.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250210160711.24010-1-ville.syrjala@linux.intel.com
Move VRR enabling/disabling into a place where it also works
for fastsets.
With this we always start the transcoder up in non-VRR mode.
Granted we already did that but for a very short period of
time. But now that we might end up doing a bit more with the
transcoder in non-VRR mode it seems prudent to also update
the active timings as the transcoder changes its operating
mode.
crtc_state->vrr.enable still tracks whether VRR is actually
enabled or not, but now we configure all the other VRR timing
registers whenever VRR is possible (whether we actually enable
it or not). crtc_state->vrr.flipline can now serve as our
"is VRR possible" bit of state.
I decided to leave the MSA timing ignore bit set all the time
whether VRR is actually enabled or not. If the sink can figure
out the timings with that information when VRR is active then
surely it can also do it when VRR is inactive.
v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321135615.27338-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Let's adjust the vblank evasion to account for the case where
a push has already been sent. In that case the vblank exit will start
at vmin vblank start (as opposed to vmax vblank start when no push
has been sent).
This should minimize the effects of the tiny race between sampling
the frame counter vs. intel_vrr_send_push() during the previous frame.
This will also be required if we want to do mailbox style updates with
vrr since then we'd definitely do multiple commits per frame. Currently
mailbox updates are only used by the legacy cursor, but we don't do
vrr push for those.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211117183103.27418-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
VRR achieves vblank stretching using the HW PUSH functionality.
So once the VRR is enabled during modeset then for each flip
request from userspace, in the atomic tail pipe_update_end()
we need to set the VRR push bit in HW for it to terminate
the vblank at configured flipline or anytime after flipline
or latest at the Vmax.
The HW clears the PUSH bit after the double buffer updates
are completed.
v2:
* Move send push to after irq en (Manasi)
* Call send push unconditionally (Jani N)
v3:
* Stall w.r.t Vrr vmax (Manasi, Gary Smith)
v4:
* Remove the rmw (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gary Smith <gary.k.smith@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-11-manasi.d.navare@intel.com
This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.
v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com
