port_fdb_dump() is supposed to only add fdb entries, but we iterate over
the full ARL table, which also includes multicast entries.
So check if the entry is a multicast entry before passing it on to the
callback().
Additionally, the port of those entries is a bitmask, not a port number,
so any included entries would have even be for the wrong port.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251217205756.172123-1-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
BCM5325/65's ARL entry registers do not contain the VID, only the search
result register does. ARL entries have a separate VID entry register for
the index into the VLAN table.
So make ARL entry accessors use the VID entry registers instead, and
move the VLAN ID field definition to the search register definition.
Fixes: c45655386e ("net: dsa: b53: add support for FDB operations on 5325/5365")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251128080625.27181-7-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently use the mask 0xf for writing and reading b53_entry::port,
but this is only correct for unicast ARL entries. Multicast ARL entries
use a bitmask, and 0xf is not enough space for ports > 3, which includes
the CPU port.
So extend the mask accordingly to also fit port 4 (bit 4) and MII (bit
5). According to the datasheet the multicast port mask is [60:48],
making it 12 bit wide, but bits 60-55 are reserved anyway, and collide
with the priority field at [60:59], so I am not sure if this is valid.
Therefore leave it at the actual used range, [53:48].
The ARL search result register differs a bit, and there the mask is only
[52:48], so only spanning the user ports. The MII port bit is
contained in the Search Result Extension register. So create a separate
search result parse function that properly handles this.
Fixes: c45655386e ("net: dsa: b53: add support for FDB operations on 5325/5365")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20251128080625.27181-6-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ARL registers of BCM63XX embedded switches are somewhat unique. The
normal ARL table access registers have the same format as BCM5389, but
the ARL search registers differ:
* SRCH_CTL is at the same offset of BCM5389, but 16 bits wide. It does
not have more fields, just needs to be accessed by a 16 bit read.
* SRCH_RSLT_MACVID and SRCH_RSLT are aligned to 32 bit, and have shifted
offsets.
* SRCH_RSLT has a different format than the normal ARL data entry
register.
* There is only one set of ENTRY_N registers, implying a 1 bin layout.
So add appropriate ops for bcm63xx and let it use it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251107080749.26936-9-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.18-rc5).
Conflicts:
drivers/net/wireless/ath/ath12k/mac.c
9222582ec5 ("Revert "wifi: ath12k: Fix missing station power save configuration"")
6917e268c4 ("wifi: ath12k: Defer vdev bring-up until CSA finalize to avoid stale beacon")
https://lore.kernel.org/11cece9f7e36c12efd732baa5718239b1bf8c950.camel@sipsolutions.net
Adjacent changes:
drivers/net/ethernet/intel/Kconfig
b1d16f7c00 ("libie: depend on DEBUG_FS when building LIBIE_FWLOG")
93f53db9f9 ("ice: switch to Page Pool")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When iterating over the ARL table we stop at max ARL entries / 2, but
this is only valid if the chip actually returns 2 results at once. For
chips with only one result register we will stop before reaching the end
of the table if it is more than half full.
Fix this by only dividing the maximum results by two if we have a chip
with more than one result register (i.e. those with 4 ARL bins).
Fixes: cd169d799b ("net: dsa: b53: Bound check ARL searches")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-4-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch clears the ARL_SRCH_STDN bit when the search is done, i.e. it
finished traversing the ARL table.
This means that there will be no valid result, so we should not attempt
to read and process any further entries.
We only ever check the validity of the entries for 4 ARL bin chips, and
only after having passed the first entry to the b53_fdb_copy().
This means that we always pass an invalid entry at the end to the
b53_fdb_copy(). b53_fdb_copy() does check the validity though before
passing on the entry, so it never gets passed on.
On < 4 ARL bin chips, we will even continue reading invalid entries
until we reach the result limit.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the New Control register bit 1 is either reserved, or has a different
function:
Out of Range Error Discard
When enabled, the ingress port discards any frames
if the Length field is between 1500 and 1536
(excluding 1500 and 1536) and with good CRC.
The actual bit for enabling IP multicast is bit 0, which was only
explicitly enabled for BCM5325 so far.
For older switch chips, this bit defaults to 0, so we want to enable it
as well, while newer switch chips default to 1, and their documentation
says "It is illegal to set this bit to zero."
So drop the wrong B53_IPMC_FWD_EN define, enable the IP multicast bit
also for other switch chips. While at it, rename it to (B53_)IP_MC as
that is how it is called in Broadcom code.
Fixes: 63cc54a6f0 ("net: dsa: b53: Fix egress flooding settings")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251102100758.28352-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM63XX's switch does not support MDIO scanning of external phys, so its
MACs needs to be manually configured for autonegotiated link speeds.
So b53_force_port_config() and b53_force_link() accordingly also when
mode is MLO_AN_PHY for those ports.
Fixes lower speeds than 1000/full on rgmii ports 4 - 7.
This aligns the behaviour with the old bcm63xx_enetsw driver for those
ports.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251101132807.50419-3-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is no guarantee that the port state override registers have their
default values, as not all switches support being reset via register or
have a reset GPIO.
So when forcing port config, we need to make sure to clear all fields,
which we currently do not do for the speed and flow control
configuration. This can cause flow control stay enabled, or in the case
of speed becoming an illegal value, e.g. configured for 1G (0x2), then
setting 100M (0x1), results in 0x3 which is invalid.
For PORT_OVERRIDE_SPEED_2000M we need to make sure to only clear it on
supported chips, as the bit can have different meanings on other chips,
e.g. for BCM5389 this controls scanning PHYs for link/speed
configuration.
Fixes: 5e004460f8 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251101132807.50419-2-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.17-rc6).
Conflicts:
net/netfilter/nft_set_pipapo.c
net/netfilter/nft_set_pipapo_avx2.c
c4eaca2e10 ("netfilter: nft_set_pipapo: don't check genbit from packetpath lookups")
84c1da7b38 ("netfilter: nft_set_pipapo: use avx2 algorithm for insertions too")
Only trivial adjacent changes (in a doc and a Makefile).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For some reason Broadcom decided that BCM53101 uses 0.5s increments for
the ageing time register, but kept the field width the same [1]. Due to
this, the actual ageing time was always half of what was configured.
Fix this by adapting the limits and value calculation for BCM53101.
So far it looks like this is the only chip with the increased tick
speed:
$ grep -l -r "Specifies the aging time in 0.5 seconds" cdk/PKG/chip | sort
cdk/PKG/chip/bcm53101/bcm53101_a0_defs.h
$ grep -l -r "Specifies the aging time in seconds" cdk/PKG/chip | sort
cdk/PKG/chip/bcm53010/bcm53010_a0_defs.h
cdk/PKG/chip/bcm53020/bcm53020_a0_defs.h
cdk/PKG/chip/bcm53084/bcm53084_a0_defs.h
cdk/PKG/chip/bcm53115/bcm53115_a0_defs.h
cdk/PKG/chip/bcm53118/bcm53118_a0_defs.h
cdk/PKG/chip/bcm53125/bcm53125_a0_defs.h
cdk/PKG/chip/bcm53128/bcm53128_a0_defs.h
cdk/PKG/chip/bcm53134/bcm53134_a0_defs.h
cdk/PKG/chip/bcm53242/bcm53242_a0_defs.h
cdk/PKG/chip/bcm53262/bcm53262_a0_defs.h
cdk/PKG/chip/bcm53280/bcm53280_a0_defs.h
cdk/PKG/chip/bcm53280/bcm53280_b0_defs.h
cdk/PKG/chip/bcm53600/bcm53600_a0_defs.h
cdk/PKG/chip/bcm89500/bcm89500_a0_defs.h
[1] a5d3fc9b12/cdk/PKG/chip/bcm53101/bcm53101_a0_defs.h (L28966)
Fixes: e39d14a760 ("net: dsa: b53: implement setting ageing time")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20250905124507.59186-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
BCM5325 and BCM5365 are part of a much older generation of switches which,
due to their limited number of ports and VLAN entries (up to 256) allowed
a single 64-bit register to hold a full ARL entry.
This requires a little bit of massaging when reading, writing and
converting ARL entries in both directions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Link: https://patch.msgid.link/20250614080000.1884236-6-noltari@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When Linux sends out untagged traffic from a port, it will enter the CPU
port without any VLAN tag, even if the port is a member of a vlan
filtering bridge with a PVID egress untagged VLAN.
This makes the CPU port's PVID take effect, and the PVID's VLAN
table entry controls if the packet will be tagged on egress.
Since commit 45e9d59d39 ("net: dsa: b53: do not allow to configure
VLAN 0") we remove bridged ports from VLAN 0 when joining or leaving a
VLAN aware bridge. But we also clear the untagged bit, causing untagged
traffic from the controller to become tagged with VID 0 (and priority
0).
Fix this by not touching the untagged map of VLAN 0. Additionally,
always keep the CPU port as a member, as the untag map is only effective
as long as there is at least one member, and we would remove it when
bridging all ports and leaving no standalone ports.
Since Linux (and the switch) treats VLAN 0 tagged traffic like untagged,
the actual impact of this is rather low, but this also prevented earlier
detection of the issue.
Fixes: 45e9d59d39 ("net: dsa: b53: do not allow to configure VLAN 0")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250602194914.1011890-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add RGMII to supported interfaces for BCM63xx RGMII ports so they can be
actually used in RGMII mode.
Without this, phylink will fail to configure them:
[ 3.580000] b53-switch 10700000.switch GbE3 (uninitialized): validation of rgmii with support 0000000,00000000,00000000,000062ff and advertisement 0000000,00000000,00000000,000062ff failed: -EINVAL
[ 3.600000] b53-switch 10700000.switch GbE3 (uninitialized): failed to connect to PHY: -EINVAL
[ 3.610000] b53-switch 10700000.switch GbE3 (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 4
Fixes: ce3bf94871 ("net: dsa: b53: add support for BCM63xx RGMIIs")
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://patch.msgid.link/20250602193953.1010487-5-jonas.gorski@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
