On my R9 390, the voltage was reported as a constant 1000 mV.
This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor()
function, where some magic constants were used in a condition,
to determine whether the voltage should be read from PLANE2_VID
or PLANE1_VID. The VDDC mask was incorrectly used, instead of
the VDDGFX mask.
This patch changes the code to use the correct defined constants
(and apply the correct bitshift), thus resulting in correct voltage reporting.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Normally softwareshutdowntemp should be greater than Thotspotlimit.
However, on some VEGA10 ASIC, the softwareshutdowntemp is 91C while
Thotspotlimit is 105C. This seems not right and may trigger some
false alarms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
DC uses these to raise the voltage as needed for higher dispclk/dppclk
and to ensure that we have enough bandwidth to drive the displays.
There's a bug preventing these from actuially sending messages since
it's checking the actual clock (which is 0) instead of the incoming
clock (which shouldn't be 0) when deciding to send the hardmin.
[How]
Check the clocks != 0 instead of the actual clocks.
Fixes: 9ed9203c3e ("drm/amd/powerplay: rv dal-pplib interface refactor powerplay part")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Do the maths in celsius degree. This can fix the issues caused
by the changes below:
drm/amd/pm: correct Vega20 swctf limit setting
drm/amd/pm: correct Vega12 swctf limit setting
drm/amd/pm: correct Vega10 swctf limit setting
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The UVD/VCE PG state is managed by UVD and VCE IP. It's error-prone to
assume the bootup state in SMU based on the dpm status.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add some APU flags to simplify handling of different APU
variants. It's easier to understand the special cases
if we use names flags rather than checking device ids and
silicon revisions.
v2: rebase on latest code
Acked-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current codebase makes use of one-element arrays in the following
form:
struct something {
int length;
u8 data[1];
};
struct something *instance;
instance = kmalloc(sizeof(*instance) + size, GFP_KERNEL);
instance->length = size;
memcpy(instance->data, source, size);
but the preferred mechanism to declare variable-length types such as
these ones is a flexible array member[1][2], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on. So, replace
the one-element array with a flexible-array member.
Also, make use of the new struct_size() helper to properly calculate the
size of struct smu10_voltage_dependency_table.
This issue was found with the help of Coccinelle and, audited and fixed
_manually_.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The prompts will contain pci address(segment/bus/port/function),
severity(warn or error) and some keywords(GPU, amdgpu). Also this
address the issue that pci bus retrieved by PCI_BUS_NUM(adev->pdev->devfn)
is wrong.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The struct member 'asic_setup' was assigned twice, let's remove one:
static const struct pp_hwmgr_func smu10_hwmgr_funcs = {
......
.asic_setup = NULL,
......
.asic_setup = smu10_setup_asic_task,
......
};
This fixes the following coccicheck warning:
drivers/gpu/drm/amd/powerplay/hwmgr/smu10_hwmgr.c:1357:52-53:
asic_setup: first occurrence line 1360, second occurrence line 1388
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following gcc warning:
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/vega10_powertune.c:710:46:
warning: ‘PSMGCEDCThresholdConfig_vega10’ defined but not used
[-Wunused-const-variable=]
static const struct vega10_didt_config_reg
PSMGCEDCThresholdConfig_vega10[] =
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/vega10_powertune.c:654:46:
warning: ‘PSMSEEDCThresholdConfig_Vega10’ defined but not used
[-Wunused-const-variable=]
static const struct vega10_didt_config_reg
PSMSEEDCThresholdConfig_Vega10[] =
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Initialize thermal controller fields in the PowerPlay table for Hawaii
GPUs, so that fan speeds are reported.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the smu10, smu12, and gfx9 drivers to use headers for
registers instead of hardcoding in the C source files.
Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The automated conversion of /* fallthrough */ comments converted
a comment outside of an #ifdef/#endif case block that should be
inside the block.
Move the fallthrough inside the block to silence the warning.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes coccicheck warning:
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:723:2-50: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:733:3-52: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:747:3-51: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Under sriov pp one vf mode, there is no need to set
soc clk under pp one vf because smu firmware will depend
on the mclk to set the appropriate soc clk for it.
Signed-off-by: Yintian Tao <yttao@amd.com>
Reviewed-by : Monk Liu <monk.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are several occurrances of the pointer hwmgr being dereferenced
before it is null checked. Fix these by performing the dereference
of hwmgr after it has been null checked.
Addresses-Coverity: ("Dereference before null check")
Fixes: c9ffa427db ("drm/amd/powerplay: enable pp one vf mode for vega10")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Originally, due to the restriction from PSP and SMU, VF has
to send message to hypervisor driver to handle powerplay
change which is complicated and redundant. Currently, SMU
and PSP can support VF to directly handle powerplay
change by itself. Therefore, the old code about the handshake
between VF and PF to handle powerplay will be removed and VF
will use new the registers below to handshake with SMU.
mmMP1_SMN_C2PMSG_101: register to handle SMU message
mmMP1_SMN_C2PMSG_102: register to handle SMU parameter
mmMP1_SMN_C2PMSG_103: register to handle SMU response
v2: remove module parameter pp_one_vf
v3: fix the parens
v4: forbid vf to change smu feature
v5: use hwmon_attributes_visible to skip sepicified hwmon atrribute
v6: change skip condition at vega10_copy_table_to_smc
Signed-off-by: Yintian Tao <yttao@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/powerplay/hwmgr/vega10_hwmgr.c: In function vega10_get_performance_level:
drivers/gpu/drm/amd/powerplay/hwmgr/vega10_hwmgr.c:5217:23: warning: variable data set but not used [-Wunused-but-set-variable]
'data' is introduced by commit f688b614b6 ("drm/amd/pp:
Implement get_performance_level for legacy dgpu"), but never used,
so remove it.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c: In function smu7_check_mc_firmware:
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:4215:11: warning: variable vbios_version set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c: In function smu7_get_performance_level:
drivers/gpu/drm/amd/powerplay/hwmgr/smu7_hwmgr.c:5054:21: warning: variable data set but not used [-Wunused-but-set-variable]
'vbios_version' is introduced by commit 599a7e9fe1 ("drm/amd/powerplay:
implement smu7 hwmgr to manager asics with smu ip version 7."),
but never used, so remove it.
'data' is introduced by commit f688b614b6 ("drm/amd/pp:
Implement get_performance_level for legacy dgpu"), but never used,
so remove it.
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is to improve the performance in the compute mode
for vega10. For example, the original performance for a rocm
bandwidth test: 2G internal GPU copy, is about 99GB/s.
With the idle power features disabled dynamically, the porformance
is promoted to about 215GB/s.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add xgmi pstate setting on powerplay routine.
V2: split the change of is_support_sw_smu_xgmi into a separate patch
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
