This commit adds the dt-binding for KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
This binding is necessary to set specific capabilities for this switch
chip that are necessary due to the ksz dsa driver only accepting
specific chip ids.
The KSZ8567 is very similar to KSZ9567 however only containing 100 Mbps
phys on its downstream ports.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-1-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Extend device tree bindings to support drive strength configuration for the
ksz* switches. Introduced properties:
- microchip,hi-drive-strength-microamp: Controls the drive strength for
high-speed interfaces like GMII/RGMII and more.
- microchip,lo-drive-strength-microamp: Governs the drive strength for
low-speed interfaces such as LEDs, PME_N, and others.
- microchip,io-drive-strength-microamp: Controls the drive strength for
for undocumented Pads on KSZ88xx variants.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz switch driver allows specifying an interrupt line to prevent
having to periodically poll the switch for link ups/downs and other
asynchronous events.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
DSA switches can fall into one of two categories: switches where all ports
follow standard '(ethernet-)?port' properties, and switches that have
additional properties for the ports.
The scenario where DSA ports are all standardized can be handled by
switches with a reference to the new 'dsa.yaml#/$defs/ethernet-ports'.
The scenario where DSA ports require additional properties can reference
'$dsa.yaml#' directly. This will allow switches to reference these standard
definitions of the DSA switch, but add additional properties under the port
nodes.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk> # realtek
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz_switch_chips[] element for KSZ9477 says that port 5 is an xMII
port and it supports speeds of 10/100/1000. The device tree example does
declare a fixed-link at 1000, and RGMII is the only one of those modes
that supports this speed, so use this phy-mode.
The microchip,ksz8565 compatible string is not supported by the
microchip driver, however on Microchip's product page it says that there
are 5 ports, 4 of which have internal PHYs and the 5th is an
MII/RMII/RGMII port. It's a bit strange that this is port@6, but it is
probably just the way it is. Select an RGMII phy-mode for this one as
well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
Document the new microchip,synclko-disable property which can be
specified to disable the reference clock output from the device if not
required by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
