[Why]
PSR support could vary from the panels connected to one GPU versus
another.
[How]
Move PSR support message into amdgpu_dm which has the scope of the
GPU and use that information.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDCP locality check has strict timing requirements, currently broken
due to reliance on msleep which does not guarantee accuracy.
The PR moves the write-poll-read sequence into DMUB using new generic
Fused IO interface, where the timing accuracy is greatly improved.
New flow is enabled using DCN resource capability bit (none for now),
or using a debug flag.
[How]
* Extended mod_hdcp_config with new function for requesting DMUB
to execute a sequence of fused I2C/AUX commands and synchronously
wait until an outbox reply arrives or a timeout expires.
* If the timeout expires, send an abort to DMUB.
* Update HDCP to use the DMUB for locality check if supported.
* Add DC_HDCP_LC_FORCE_FW_ENABLE and DC_HDCP_LC_ENABLE_SW_FALLBACK.
* Make the first enable new flow regardless of resource capabilities.
* Make the second enable fallback to old SW flow.
* Clean up makefile source file listings for easier updates.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When BIOS includes a lot of custom brightness data points, walking
the entire list can be time consuming. This is most noticed when
dragging a power slider. The "higher" values are "slower" to drag
around.
[How]
Move custom brightness calculation loop into a static function. Before
starting the loop check the "half way" data point to see how it compares
to the input. If greater than the half way data point use that as the
starting point instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In the mode validation, mst dsc is considered for bw calculation after
common dsc config is determined. Currently it considered common dsc config
is found if max and min target bpp are non zero which is not accurate. Invalid
max and min target bpp values would not get max_kbps and min_kbps calculated,
leading to falsefully pass a mode that does not have valid dsc parameters
available.
[how]
Use the return value of decide_dsc_bandwidth_range() to determine whether valid
dsc common config is found or not. Prune out modes that do not have valid common
dsc config determined.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Depending on when the HW latching event (vupdate) of double-buffered
registers happen relative to the PSR SDP (signals panel psr enter/exit)
deadline, and how bad the Panel clock has drifted since the last ALPM
off event, there can be up to 3 frames of delay between sending the PSR
exit cmd to DMUB fw, and when the panel starts displaying live frames.
This can manifest as micro-stuttering when userspace commit patterns
cause rapid toggling of the DRM vblank counter, since PSR enter/exit is
hooked up to DRM vblank disable/enable respectively.
In the ideal world, the panel should present the live frame immediately
on PSR exit cmd. But due to HW design and PSR limitations, immediate
exit can only happen by chance, when:
1. PSR exit cmd is ack'd by FW before HW latching (vupdate) event, and
2. Panel's SDP deadline -- determined by it's PSR Start Delay in DPCD
71h -- is after the vupdate event. The PSR exit SDP can then be sent
immediately after HW latches. Otherwise, we have to wait 1 frame. And
3. There is negligible drift between the panel's clock and source clock.
Otherwise, there can be up to 1 frame of drift.
Note that this delay is not expected with Panel Replay.
[How]
Since PSR power savings can be quite substantial, and there are a lot of
systems in the wild with PSR panels, It'll be nice to have a middle
ground that balances user experience with power savings.
A simple way to achieve this is by extending the vblank offdelay, such
that additional PSR exit delays will be less perceivable.
We can set:
20/100 * offdelay_ms = 3_frames_ms
=> offdelay_ms = 5 * 3_frames_ms
This ensures that `3_frames_ms` will only be experienced as a 20% delay
on top how long the panel has been static, and thus make the delay
less perceivable.
If this ends up being too high of a percentage, it can be dropped
further in a future change.
Fixes: 537ef0f888 ("drm/amd/display: use new vblank enable policy for DCN35+")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
The displays currently don't get turned off until after other IP blocks
have been suspended. However turning off the displays first gives a
very visible response that the system is on it's way down.
[How]
Turn off displays in a prepare_suspend() callback instead when possible.
This will help for suspend and hibernate sequences.
The shutdown sequence however will not call prepare() so check whether
the state has been already saved to decide what to do.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPU reset will attempt to restore cached state, but brightness doesn't
get restored. It will come back at 100% brightness, but userspace thinks
it's the previous value.
[How]
When running resume sequence if GPU is in reset restore brightness
to previous value.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To avoid flickering during boot default brightness level set by BIOS
should be maintained for as much of the boot as feasible.
commit 2fe87f54ab ("drm/amd/display: Set default brightness according
to ACPI") attempted to set the right levels for AC vs DC, but brightness
still got reset to maximum level in initialization code for
setup_backlight_device().
[How]
Remove the hardcoded initialization in setup_backlight_device() and
instead program brightness value to match BIOS (AC or DC). This avoids a
brightness flicker from kernel changing the value. Userspace may however
still change it during boot.
Fixes: 2fe87f54ab ("drm/amd/display: Set default brightness according to ACPI")
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It seems HPD interrupts are enabled by default for all connectors, even
if the hpd source isn't valid. An eDP for example, does not have a valid
hpd source (but does have a valid hpdrx source; see construct_phy()).
Thus, eDPs should have their hpd interrupt disabled.
In the past, this wasn't really an issue. Although the driver gets
interrupted, then acks by writing to hw registers, there weren't any
subscribed handlers that did anything meaningful (see
register_hpd_handlers()).
But things changed with the introduction of IPS. s2idle requires that
the driver allows IPS for DMUB fw to put hw to sleep. Since register
access requires hw to be awake, the driver will block IPS entry to do
so. And no IPS means no hw sleep during s2idle.
This was the observation on DCN35 systems with an eDP. During suspend,
the eDP toggled its hpd pin as part of the panel power down sequence.
The driver was then interrupted, and acked by writing to registers,
blocking IPS entry.
[How]
Since DC marks eDP connections as having invalid hpd sources (see
construct_phy()), DM should disable them at the hw level. Do so in
amdgpu_dm_hpd_init() by disabling all hpd ints first, then selectively
enabling ones for connectors that have valid hpd sources.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We advertise DCC as supported for NV12/P010 formats on GFX12,
but it would fail on this check on atomic commit.
Signed-off-by: David Rosca <david.rosca@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_* macros are more helpful that DRM_* macros since the former
indicates the associated DRM device that prints the error, which maybe
helpful when debugging.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Upgrading the kernel may cause some systems that were previously not using
a firmware specified brightness curve to use one.
In the event of problems with this curve (for example an interpolation
error) add a new dcdebugmask value that can be used to turn it off. Also
add an info message to show that custom brightness curves are currently in
use.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-6-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All cases except a failure to create a copy of the current context will
call dc_state_release() on the copied context.
Use a _free() macro to free the context and then adjust the error handling
flow to drop the unnecessary use of goto statements.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
