mirror of
https://github.com/torvalds/linux.git
synced 2026-04-28 03:22:27 -04:00
41c1855232
As discussed in [1] it is more convenient to use a generic `channel` node name for ADC channels while storing a friendly - board-specific instead of PMIC-specific - name in the label, if/when desired to overwrite the channel description already contained (but previously unused) in the driver [2]. Follow up on the dt-bindings' `channel` node name requirement, and instead provide this (sometimes per-board) channel description through a label property. Also remove all the unused label references (not to be confused with label properties) from pm660, pmp8074 and pms405. [1]: https://lore.kernel.org/linux-arm-msm/20221106193018.270106-1-marijn.suijten@somainline.org/T/#u [2]: https://lore.kernel.org/linux-arm-msm/20230116220909.196926-4-marijn.suijten@somainline.org/ Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20230730-generic-adc-channels-v5-2-e6c69bda8034@somainline.org Signed-off-by: Bjorn Andersson <andersson@kernel.org>
142 lines
2.7 KiB
Plaintext
142 lines
2.7 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
|
|
* Copyright (c) 2019, Linaro Limited
|
|
*/
|
|
|
|
#include <dt-bindings/iio/qcom,spmi-vadc.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pm8150b-thermal {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
|
|
thermal-sensors = <&pm8150b_temp>;
|
|
|
|
trips {
|
|
trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "hot";
|
|
};
|
|
|
|
trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&spmi_bus {
|
|
pmic@2 {
|
|
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
|
|
reg = <0x2 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pon@800 {
|
|
compatible = "qcom,pm8916-pon";
|
|
reg = <0x0800>;
|
|
|
|
status = "disabled";
|
|
};
|
|
|
|
pm8150b_vbus: usb-vbus-regulator@1100 {
|
|
compatible = "qcom,pm8150b-vbus-reg";
|
|
status = "disabled";
|
|
reg = <0x1100>;
|
|
};
|
|
|
|
pm8150b_temp: temp-alarm@2400 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0x2400>;
|
|
interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
io-channels = <&pm8150b_adc ADC5_DIE_TEMP>;
|
|
io-channel-names = "thermal";
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm8150b_adc: adc@3100 {
|
|
compatible = "qcom,spmi-adc5";
|
|
reg = <0x3100>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#io-channel-cells = <1>;
|
|
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
|
|
channel@0 {
|
|
reg = <ADC5_REF_GND>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "ref_gnd";
|
|
};
|
|
|
|
channel@1 {
|
|
reg = <ADC5_1P25VREF>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "vref_1p25";
|
|
};
|
|
|
|
channel@6 {
|
|
reg = <ADC5_DIE_TEMP>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "die_temp";
|
|
};
|
|
|
|
channel@9 {
|
|
reg = <ADC5_CHG_TEMP>;
|
|
qcom,pre-scaling = <1 1>;
|
|
label = "chg_temp";
|
|
};
|
|
};
|
|
|
|
pm8150b_adc_tm: adc-tm@3500 {
|
|
compatible = "qcom,spmi-adc-tm5";
|
|
reg = <0x3500>;
|
|
interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
|
|
#thermal-sensor-cells = <1>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pm8150b_gpios: gpio@c000 {
|
|
compatible = "qcom,pm8150b-gpio", "qcom,spmi-gpio";
|
|
reg = <0xc000>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pm8150b_gpios 0 0 12>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
};
|
|
|
|
pmic@3 {
|
|
compatible = "qcom,pm8150b", "qcom,spmi-pmic";
|
|
reg = <0x3 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm8150b_lpg: pwm {
|
|
compatible = "qcom,pm8150b-lpg";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
#pwm-cells = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|