mirror of
https://github.com/torvalds/linux.git
synced 2026-04-22 08:44:02 -04:00
a1c7da5fb0
The address/size cells in PWM node are needed only if individual LEDs
are listed. If multi-led is used, then this leads to dtc W=1 warnings:
pm8550.dtsi:65.19-73.5: Warning (avoid_unnecessary_addr_size): /soc@0/spmi@c400000/pmic@1/pwm:
unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231208124332.48636-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
73 lines
1.4 KiB
Plaintext
73 lines
1.4 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2022, Linaro Limited
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
/ {
|
|
thermal-zones {
|
|
pm8550-thermal {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
|
|
thermal-sensors = <&pm8550_temp_alarm>;
|
|
|
|
trips {
|
|
trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "hot";
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
|
|
&spmi_bus {
|
|
pm8550: pmic@1 {
|
|
compatible = "qcom,pm8550", "qcom,spmi-pmic";
|
|
reg = <0x1 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pm8550_temp_alarm: temp-alarm@a00 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0xa00>;
|
|
interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pm8550_gpios: gpio@8800 {
|
|
compatible = "qcom,pm8550-gpio", "qcom,spmi-gpio";
|
|
reg = <0x8800>;
|
|
gpio-controller;
|
|
gpio-ranges = <&pm8550_gpios 0 0 12>;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
pm8550_flash: led-controller@ee00 {
|
|
compatible = "qcom,pm8550-flash-led", "qcom,spmi-flash-led";
|
|
reg = <0xee00>;
|
|
status = "disabled";
|
|
};
|
|
|
|
pm8550_pwm: pwm {
|
|
compatible = "qcom,pm8550-pwm", "qcom,pm8350c-pwm";
|
|
#pwm-cells = <2>;
|
|
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|