mirror of
https://github.com/torvalds/linux.git
synced 2026-04-22 08:44:02 -04:00
bf223612a4
This patch reads charge delay from tsc DT node and writes to REG_CHARGEDELAY register. If the charge delay is not specified in DT then default value of 0x400(CHARGEDLY_OPENDLY) is used. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
60 lines
2.1 KiB
Plaintext
60 lines
2.1 KiB
Plaintext
* TI - TSC ADC (Touschscreen and analog digital converter)
|
|
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
|
|
|
Required properties:
|
|
- child "tsc"
|
|
ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
|
|
support on the platform.
|
|
ti,x-plate-resistance: X plate resistance
|
|
ti,coordinate-readouts: The sequencer supports a total of 16
|
|
programmable steps each step is used to
|
|
read a single coordinate. A single
|
|
readout is enough but multiple reads can
|
|
increase the quality.
|
|
A value of 5 means, 5 reads for X, 5 for
|
|
Y and 2 for Z (always). This utilises 12
|
|
of the 16 software steps available. The
|
|
remaining 4 can be used by the ADC.
|
|
ti,wire-config: Different boards could have a different order for
|
|
connecting wires on touchscreen. We need to provide an
|
|
8 bit number where in the 1st four bits represent the
|
|
analog lines and the next 4 bits represent positive/
|
|
negative terminal on that input line. Notations to
|
|
represent the input lines and terminals resoectively
|
|
is as follows:
|
|
AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
|
|
XP = 0, XN = 1, YP = 2, YN = 3.
|
|
- child "adc"
|
|
ti,adc-channels: List of analog inputs available for ADC.
|
|
AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7.
|
|
|
|
Optional properties:
|
|
- child "tsc"
|
|
ti,charge-delay: Length of touch screen charge delay step in terms of
|
|
ADC clock cycles. Charge delay value should be large
|
|
in order to avoid false pen-up events. This value
|
|
effects the overall sampling speed, hence need to be
|
|
kept as low as possible, while avoiding false pen-up
|
|
event. Start from a lower value, say 0x400, and
|
|
increase value until false pen-up events are avoided.
|
|
The pen-up detection happens immediately after the
|
|
charge step, so this does in fact function as a
|
|
hardware knob for adjusting the amount of "settling
|
|
time".
|
|
|
|
Example:
|
|
tscadc: tscadc@44e0d000 {
|
|
compatible = "ti,am3359-tscadc";
|
|
tsc {
|
|
ti,wires = <4>;
|
|
ti,x-plate-resistance = <200>;
|
|
ti,coordiante-readouts = <5>;
|
|
ti,wire-config = <0x00 0x11 0x22 0x33>;
|
|
ti,charge-delay = <0x400>;
|
|
};
|
|
|
|
adc {
|
|
ti,adc-channels = <4 5 6 7>;
|
|
};
|
|
}
|