Program the timeout values (in escape clock) for HS TX, LP RX and TA
timeout.
HX TX: Ensure that host does not continuously transmit in the HS
state. If this timer expires, then host will gracefully end its HS
transmission and allow the link to enter into LP state.
LP RX: Monitor the length of LP receptions from Peripheral. If timeout
happens then host will drive the stop state onto all data lanes (only
Data Lane 0 should be receiving anything from the Peripheral). This
effectively takes back ownership of the bus transmit in the HS state.
TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence.
BTA sequence should complete within a bounded amount of time, with
peripheral acknowledging BTA by driving the stop state.
v2 by Jani:
- Rebase
- Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi)
- Squash HX TX, LP RX and TA timeout into one patch
- Fix bspec mode set sequence reference
- Add FIXME about two timeouts
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/60e610ccffe5f8c09dee1c65828f28f25227efce.1540900289.git.jani.nikula@intel.com
Driver needs payload/header credits for sending any command
and data over DSI link. These credits are released once command
or data sent to link. This patch adds functions to wait for releasing
of payload and header credits.
As per BSPEC, driver needs to ensure that all of commands/data
has been dispatched to panel before the transcoder is enabled.
This patch implement those steps i.e. sending NOP DCS command,
wait for header/payload credit to be released etc.
v2 by Jani:
- squash the credit wait helpers patch with the first user
- pass dev_priv to the credit wait helpers
- bikeshed credit helper names
- wait for *at least* the current maximum number of credits
- indentation fix
- add helpers for credits available
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/84bc509beabf2a2d1324a9f2a67ab4ebe05b10a6.1540900289.git.jani.nikula@intel.com
GVT-g only simulates DP port for guest and leaves EDP_PSR_IMR
and EDP_PSR_IIR registers as default MMIO read/write.
So guest won't get expected initial values of these registers when
initializing the gpu driver, which results in following warning and logs.
--------
Interrupt register 0x64838 is not zero: 0xffffffff
WARNING: CPU: 1 PID: 157 at drivers/gpu/drm/i915/i915_irq.c:177
gen3_assert_iir_is_zero+0x38/0xa0
Call Trace:
gen8_de_irq_postinstall+0xa7/0x400
gen8_irq_postinstall+0x27/0x80
drm_irq_install+0xbc/0x140
i915_driver_load+0xa9d/0xd50
--------
Because GVT-g does not handle EDP(embedded DP) simulation for guests,
always set EDP_PSR_IMR and EDP_PSR_IIR to value 0.
Signed-off-by: Longhe Zheng <longhe.zheng@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
CSFE_CHICKEN1(0x20d4) needs access with mask. This is caught in AcrnGT
conformance check test:
[drm:intel_gvt_vgpu_conformance_check]
*ERROR* gvt: vgpu1 unconformance mmio 0x20d4:0x40004,0x4
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously we assumed two 4-byte writes to the same PTE coming in sequence.
But recently we observed inconsecutive partial write happening as well. So
this patch enhances the previous solution. It now uses a list to save more
partial writes. If one partial write can be combined with another one in
the list to construct a full PTE, update its shadow entry. Otherwise, save
the partial write in the list.
v2: invalidate old entry and flush ggtt (Zhenyu)
v3: split old ggtt page unmap to another patch (Zhenyu)
v4: refine codes (Zhenyu)
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Cc: Yan Zhao <yan.y.zhao@intel.com>
Cc: Xiaolin Zhang <xiaolin.zhang@intel.com>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
I want to sort out support for tinydrm in vc4, so I needed to get a
tinydrm-appropriate panel working and this is what I had on hand.
This is derived from a combination of ili9341.c from tinydrm and
fb_hx8357d.c from staging's fbtft.
v2: Write my own register defs from the spec to not need the header
from fbtft. Fix spi device string to enable module autoloading.
(Suggestions by Noralf)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024184313.2967-3-eric@anholt.net
Reviewed-by: Noralf Trønnes <noralf@tronnes.org> (v1)
This patch will work as workaround for silicon limitation
related to PWM dutycycle when the backlight level goes to 0.
Actually PWM value is 16 bit value and valid range from 1-65535.
when ever user requested to set this PWM value to 0 which is not
fall in the range, in VBIOS taken care this by limiting to 1.
This patch here will do the same. Either driver or VBIOS can not
pass 0 value as it is not a valid range for PWM and it will
give a high PWM pulse which is not the intended behaviour as
per HW constraints.
Signed-off-by: suresh guttula <suresh.guttula@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable
DC5/6 when appropriate.
v2: (James Ausmus)
- Also handle ICL as GEN9_LP in i915_drm_suspend_late and
i915_drm_suspend_early
- Add DC9 to gen9_dc_mask for ICL
- Re-order GEN checks for newest platform first
- Use INTEL_GEN instead of INTEL_INFO->gen
- Use INTEL_GEN >= 11 instead of IS_ICELAKE
- Consolidate GEN checks
v3: (James Ausmus)
- Also allow DC6 for ICL (Imre, Art)
- Simplify !(GEN >= 11) to GEN < 11 (Imre)
v4: (James Ausmus)
- Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the
PPS regs are Always On
- Rebase against upstream changes
v5: (Anusha Srivatsa)
- rebased against the latest upstream changes.
v6: (Anusha Srivatsa)
- rebased.Use INTEL_GEN consistently.
- Simplify the code (Rodrigo)
v7: rebased. Change order according to platforms(Jyoti)
v8: rebased. Change the check from platform specific to
HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Tested-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029221410.4423-1-anusha.srivatsa@intel.com
Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well.
As described in the general dual-dsi devicetree binding, the panel should
define two input ports and point each of them to one of the used dsi-
controllers, as well as declare one of them as clock-master.
This is used to determine the dual-dsi state and get access to both
controller instances.
v6:
handle master+slave component in dsi-attach
v5:
use driver-internal mechanism to find dual dsi slave
v4:
add component directly in probe when adding empty dsi slave controller
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-8-heiko@sntech.de
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
Add the ROCKCHIP DSI controller driver that uses the Synopsys DesignWare
MIPI DSI host controller bridge and remove the old separate one.
changes:
v2:
add err_pllref, remove unnecessary encoder.enable & disable
correct spelling mistakes
v3:
call dw_mipi_dsi_unbind() in dw_mipi_dsi_rockchip_unbind()
fix typo, use of_device_get_match_data(),
change some bind() logic into probe()
add 'dev_set_drvdata()'
v4:
return -EINVAL when can not get best_freq
add a clarifying comment when get vco
add review tag
v5:
keep our power domain enabled while touching GRF
v6:
change func name dw_mipi_encoder_disable to
dw_mipi_dsi_encoder_disable
v7:
none
v8: Heiko
add Archit's Review tag
adapt to recent changes in the original rockchip-dsi driver
beautify grf-handling
split hw-setup (resources, dsi-host) from bind into probe
v2-new: Heiko
add SPDX header instead of license blurb
drop old versioning to not confuse people
v3-new: Heiko
include ordering
moved hwaccess from mode_set to enable callback
move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps)
v4-new: Heiko
rebase against recent rockchip-dsi changes
move to call component_add in the new glue host-attach
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-6-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
Move virtio_gpu_resource_id_{get,put} to virtgpu_object.c and make them
static. Allocate and free the id on creation and destroy, drop all
other calls. That way objects have a valid handle for the whole
lifetime of the object.
Also fixes ids leaking. Worst offender are dumb buffers, and I think
some error paths too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181019061847.18958-7-kraxel@redhat.com
