[Why]
If VBlank_nom is too small, it will cause
VStartUP_Start smaller than VBackPorch + VSync width which is an
invalid case for VStartUP_Start and where to send AS-SDP.
[How]
Setup a minimum value to VBlank_nom
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
vstartup is calculated to be a large number. it works because
it is within vertical blank, but it reduces region of blank that
can be used for power gating.
[how]
Calculation needs to convert micro seconds to number of
vertical lines.
Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
This Unit correction exposes a Replay corruption.
[how]
This reverts commit:
commit dbd29029c7 ("drm/amd/display: Correct unit conversion for vstartup")
Roll back unit conversion until Replay can fix their corruption.
Fixes: dbd29029c7 ("drm/amd/display: Correct unit conversion for vstartup")
Reviewed-by: Reza Amini <reza.amini@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DMUB subsystem was continuing to use compile time offset calculation for
register access. Switch this to runtime calculation to stay consistent
with rest of DC code.
To enable this, an additional interface init_reg_offsets() are added to
DMUB's hw_funcs struct. Asics with runtime register offset calculation
enabled shall populate this hook with a fn pointer that will invoke the
necessary macros to calculate the offset.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
To organize the edp power control a bit:
1. add flag in dc_link to indicate dc to skip all implicit eDP power control.
2. add edp_set_panel_power link service for DM to call.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
PQ has a fixed range of 0-10,000 nits.
Using 1=80 nits normalization, PQ should map to 1.0 for X=125.0
HW LUT used for interpolation does not have X=125 so it's interpolated.
However, we cap Y to 1 for all X>=125.
The closest larger HW point is 128.
What we want is Y(128) such that interpolation through 125 gives 1.0.
Such value is ~1.00256.
Another change is to hardcode PQ table, we pretty much always have 1=80
normalization so the table can be static.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
HW LUTs changed slightly in DCN3: 256 base+slope pairs were replaced by
257 bases. Code was still calculating all 256 base+slope and then
creating 257th pt as last base + last slope.
This was done in wrong format, and then "fixed" it by making the last
two points the same thus making the last slope=0.
However, this also created some precision problems near the end that
are not visible but they do show up with capture cards.
Solution is to calculate 257 and remove deltas since we no longer have
those HW registers.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
if hmm_range_get_pages returns EBUSY error during
svm_range_validate_and_map, within the context of a page fault
interrupt. This should retry through svm_range_restore_pages
callback. Therefore we treat this as EAGAIN error instead, and defer
it to restore pages fallback.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Instead of maintaining a list per device, keep the reset handlers common
per ASIC family. A pointer to the list of handlers is maintained in
reset control.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Tested-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add critical temperature message support func for smu v13.0.6
and expose critical temperature as part of hw mon attributes
for GC v9.4.3
v2:
Added comment for pmfw version requirement & move the check
to get_thermal_temperature_range function
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using kmemdup() helper function rather than implementing it again
with kmalloc() + memcpy(), which improves the code readability.
Signed-off-by: Chen Jiahao <chenjiahao16@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- There is a DPM issue where if DC is not present,
FCLK will stay at low level.
We need to send a SMU message to configure the DPM
- Reuse smu_v13_0_notify_display_change() for this purpose
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bokun Zhang <bokun.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Setup replay config on device init.
- Enable replay if feature is enabled (prioritize replay over PSR, since
it can be enabled in more usecases)
- Add debug masks to enable replay on supported ASICs
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3.1.4 is reported to hang on s2idle entry if graphics activity
is happening during entry. This is because GFXOFF was scheduled as
delayed but RLC gets disabled in s2idle entry sequence which will
hang GFX IP if not already in GFXOFF.
To help this problem, flush any delayed work for GFXOFF early in
s2idle entry sequence to ensure that it's off when RLC is changed.
commit 4b31b92b14 ("drm/amdgpu: complete gfxoff allow signal during
suspend without delay") modified power gating flow so that if called
in s0ix that it ensured that GFXOFF wasn't put in work queue but
instead processed immediately.
This is dead code due to commit 10cb67eb8a ("drm/amdgpu: skip
CG/PG for gfx during S0ix") because GFXOFF will now not be explicitly
called as part of the suspend entry code. Remove that dead code.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
GFX v11.0.1 reported fence fallback timer expired issue on
SDMA and GFX rings after S0ix resume. This is generated by
EOP interrupts are disabled when S0ix suspend but fails to
re-enable when resume because of the GFX is in GFXOFF.
[ 203.349571] [drm] Fence fallback timer expired on ring sdma0
[ 203.349572] [drm] Fence fallback timer expired on ring gfx_0.0.0
[ 203.861635] [drm] Fence fallback timer expired on ring gfx_0.0.0
For S0ix, GFX is in GFXOFF state, avoid to touch the GFX registers
to configure the fence driver interrupts for rings that belong to GFX.
The interrupts configuration will be restored by GFXOFF exit.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Update addresses of PCIE link width registers,
& link width format used to populate gpu metrics
table for smu v13.0.6
v2:
Removed ESM register update
v3:
Updated patch subject and message
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The parameter amdgpu_mcbp shall have priority against the default value
calculated from the chip version.
User could disable mcbp by setting the parameter mcbp as zero.
v2: do not trigger preemption in sw ring muxer when mcbp is disabled.
Signed-off-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3.1.4 is reported to hang on s2idle entry if graphics activity
is happening during entry. This is because GFXOFF was scheduled as
delayed but RLC gets disabled in s2idle entry sequence which will
hang GFX IP if not already in GFXOFF.
To help this problem, flush any delayed work for GFXOFF early in
s2idle entry sequence to ensure that it's off when RLC is changed.
commit 4b31b92b14 ("drm/amdgpu: complete gfxoff allow signal during
suspend without delay") modified power gating flow so that if called
in s0ix that it ensured that GFXOFF wasn't put in work queue but
instead processed immediately.
This is dead code due to commit 10cb67eb8a ("drm/amdgpu: skip
CG/PG for gfx during S0ix") because GFXOFF will now not be explicitly
called as part of the suspend entry code. Remove that dead code.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX v11.0.1 reported fence fallback timer expired issue on
SDMA and GFX rings after S0ix resume. This is generated by
EOP interrupts are disabled when S0ix suspend but fails to
re-enable when resume because of the GFX is in GFXOFF.
[ 203.349571] [drm] Fence fallback timer expired on ring sdma0
[ 203.349572] [drm] Fence fallback timer expired on ring gfx_0.0.0
[ 203.861635] [drm] Fence fallback timer expired on ring gfx_0.0.0
For S0ix, GFX is in GFXOFF state, avoid to touch the GFX registers
to configure the fence driver interrupts for rings that belong to GFX.
The interrupts configuration will be restored by GFXOFF exit.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update pcie link speed registers for smu v13.0.6 &
populate gpu metric table with pcie link speed rather than
gen for smu v13_0_0, smu v13_0_6 & smu v13_0_7
v2:
Update ESM register address
Used macro to convert pcie gen to speed
v3:
Chaged macro to inline function for pcie gen to speed
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update addresses of PCIE link width registers,
& link width format used to populate gpu metrics
table for smu v13.0.6
v2:
Removed ESM register update
v3:
Updated patch subject and message
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Improve power saving feature
- Clean up for code clarity
- Fix crashing bug
- Fix pipe allocation for older ASIC
- Fix for gamut remap
- Fix 8K 60Hz display in test cases
- Fix bug in clock gating
- Improve DP2 compliance
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some ASICS only offer one type of power attribute, so in the visible
callback check whether the attributes are supported and hide if not
supported.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
