This changes the default IOTLB flushing method to lazy flushing, which
means that there will be no direct flush after each DMA unmap operation.
Instead, the iommu bitmap pointer will be adjusted after unmap, so that
no DMA address will be re-used until after an iommu bitmap wrap-around.
The only IOTLB flush will then happen after each wrap-around.
A new kernel parameter "s390_iommu=" is also introduced, to allow changing
the flushing behaviour to the old strict method.
Reviewed-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add binding spec for Qualcomm SoC PHYs, starting with the SATA PHY on
the IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In case of multi-phy PHY providers, each PHY should be modeled as a sub
node of the PHY provider. Then each PHY will have a different node pointer
(node pointer of sub node) than that of PHY provider. Added this provision
in the PHY core.
Also fixed all drivers to use the updated API.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
The Berlin SATA PHY drives the PHY related to the SATA interface. Add
the corresponding documentation.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy-supply is a phandle to the regulator that provides power to the
PHY. This regulator is managed during the PHY power on/off sequence
by the phy core driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
8-bit delay value (0xF1) is required for GEN2 devices to be enumerated
consistently. Added an API to be called from PHY drivers to set this delay
value and called it from PIPE3 driver to set the delay value.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
PCIe PHY uses an external pll instead of the internal pll used by SATA
and USB3. So added support in pipe3 PHY to use external pll.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
This panel is used by the Medcom Wide and supported by the
simple-panel driver.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
V4L2_CID_BASE_LASTP1 should be V4L2_CID_LASTP1. This has probably been wrong
since the earliest days of this documentation until I did a copy-and-paste
and found out that V4L2_CID_BASE_LASTP1 doesn't actually exist :-)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add defines for the start line numbers of each field for both
525 and 625 line formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The fact that the pixelformat is using a packed RGB format has nothing
to do with the colorspace that is being used. Those are very different
things. The colorspace decides what color a triplet of RGB numbers
actually map to. E.g. a red color with values (255, 0, 0) is a different
type of red depending on the colorspace. If the original pixelformat was
e.g. YUV in colorspace REC709, then after the conversion to RGB the
colorspace is still REC709. Unless the hardware actually converted the
colorspace as well from REC709 to sRGB, but that rarely if ever happens.
Remove this incorrect comment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New field buffersize was added to inform application maximum
buffer size used. Add it to documentation too.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_SDR_FMT_CS14LE is complex signed 14-bit sample format, used
for software defined radio devices.
[m.chehab@samsung.com: remove V4L2_FL_USE_FH_PRIO setting to avoid
compilation breakage, as this flag doesn't exist anymore]
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
V4L2_SDR_FMT_CS8 is complex signed 8-bit sample format, used for
software defined radio devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Document V4L2_SDR_FMT_RU12LE format. It is real unsigned 12-bit
little endian sample inside 16-bit space. Used by software defined
radio devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.
As this is not always the case, the regulator is requested as optional.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Allwinner A23 SoC has a PRCM unit like the previous A31 SoC.
The differences are the AR100 clock can no longer be modified,
the APB0 clock has different divisors, and some clock gates are
gone.
This patch adds a compatible with a modified subdevice list for
the A23.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This series enables the "KVM_(S|G)ET_MP_STATE" ioctls on s390 to make
the cpu state settable by user space.
This is necessary to avoid races in s390 SIGP/reset handling which
happen because some SIGPs are handled in QEMU, while others are
handled in the kernel. Together with the busy conditions as return
value of SIGP races happen especially in areas like starting and
stopping of CPUs. (For example, there is a program 'cpuplugd', that
runs on several s390 distros which does automatic onlining and
offlining on cpus.)
As soon as the MPSTATE interface is used, user space takes complete
control of the cpu states. Otherwise the kernel will use the old way.
Therefore, the new kernel continues to work fine with old QEMUs.
Capabilities can be enabled on a vcpu or (since recently) on a vm. Document
this and note for the existing capabilites whether they are per-vcpu or
per-vm.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Merge "ARM: mvebu: DT changes for v3.17 (round 2)" from Jason Cooper:
mvebu DT changes for v3.17 (round 2):
- kirkwood
* Add d2 Network v2 board
- mvebu
* Add Armada 375 ethernet node
* Add CA9 MPcore SoC controller node
* Add support for dynamic freq scaling on Armada XP
* tag 'mvebu-dt-3.17-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: update Armada XP DT for dynamic frequency scaling
ARM: mvebu: add CA9 MPcore SoC Controller node
ARM: mvebu: Enable the network controller in Armada 375 DB board
ARM: mvebu: Add support for the network controller in Armada 375 SoC
ARM: Kirkwood: add DT support for d2 Network v2
ARM: Kirkwood: allow to use netxbig DTSI for d2net_v2 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung exynos cpuidle update for v3.17" from Kukjin Kim:
- add callbacks exynos_suspend() and exynos_powered_up()
for support cpuidle through mcpm
- skip exynos_cpuidle for exynos5420 because is uses
cpuidle-big-liggle generic cpuidle driver
- add generic functions to calculate cpu number is used
for pmu and this is required for exynos5420 multi-cluster
- add of_device_id structure for big.LITTLE cpuidle and
add "samsung,exynos5420" compatible string for exynos5420
* tag 'exynos-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: populate suspend and powered_up callbacks for mcpm
ARM: EXYNOS: do not allow cpuidle registration for exynos5420
cpuidle: big.LITTLE: init driver for exynos5420
cpuidle: big.LITTLE: Add ARCH_EXYNOS entry in config
ARM: EXYNOS: add generic function to calculate cpu number
cpuidle: big.LITTLE: add of_device_id structure
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung cleanup for v3.17" from Kukjin Kim:
Most of them are for exynos SoCs, remove useless codes and update for
PMU consolidation.
- remove unnecessary header file in mach-exynos/pmu.c
- remove unused code in mach-exynos/common.h
- remove mach-exynos/regs-pmu.h dependency from PD
- remove file path from comment section in mach-exynos
- move SYSREG definitions into mach-exynos/regs-sys.h
- add mapping PMU base address via DT for PMU cleanup
- use staic in mach-exynos/common.h
- update Samsung UART config options for low-level debug
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add support for mapping PMU base address via DT
ARM: EXYNOS: Remove "linux/bug.h" from pmu.c
ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain
ARM: EXYNOS: Remove file path from comment section
ARM: EXYNOS: Move SYSREG definition into sys-reg specific file
ARM: EXYNOS: Make exynos machine_ops as static
ARM: EXYNOS: Remove unused code in common.h
ARM: debug: Update Samsung UART config options
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: device tree changes for 3.17" from Thierry Reding:
- New board support:
* Apalis T30
- HDA support for Tegra124 and Venice2
- Display on Medcom Wide and Roth
- GK20A support on Tegra124
- XUSB pad controller for Tegra124 and Jetson TK1
- Various cleanups
This pulls in the for-3.17/fuse-move, for-3.17/dt-cros-ec-kbd and
for-3.17/xusb-padctl branches to resolve dependencies.
Note that the Apalis T30 support has a runtime dependency on the
for-3.17/pcie-regulators branch, so they should preferably be applied
in that order. I didn't merge that branch into this because Apalis T30
support is new, therefore can't regress, and because the dependency
exists only at runtime.
* tag 'tegra-for-3.17-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (28 commits)
ARM: tegra: roth: add display DT node
ARM: tegra: Fix typoed ams,ext-control properties
ARM: tegra: jetson-tk1: Add XUSB pad controller
ARM: tegra: tegra124: Add XUSB pad controller
ARM: tegra: add GK20A GPU to Tegra124 DT
ARM: tegra: of: add GK20A device tree binding
ARM: tegra: roth: enable input on mmc clock pins
ARM: tegra: roth: fix unsupported pinmux properties
ARM: tegra: Migrate Apalis T30 PCIe power supply scheme
ARM: tegra: tamonten: add the display to the Medcom Wide
ARM: tegra: tamonten: add the base board regulators
ARM: tegra: initial support for apalis t30
ARM: tegra: jetson-tk1: mark eMMC as non-removable
ARM: tegra: venice2 - Enable HDA
ARM: tegra: Add Tegra124 HDA support
ARM: tegra: Add the EC i2c tunnel to tegra124-venice2
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: Add XUSB pad controller support" from Thierry Reding:
Adds device tree bindings and a driver for the XUSB pad controller found
on Tegra114 and later. This is a prerequisites for PCIe, SATA and XUSB
drivers which are all currently being reviewed or pending for merge.
This is a separate branch in case it needs to be pulled into the pinctrl
tree to resolve conflicts.
* tag 'tegra-for-3.17-xusb-padctl' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
pinctrl: Add NVIDIA Tegra XUSB pad controller support
of: Add NVIDIA Tegra XUSB pad controller binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: rework PCIe regulators" from Thierry Reding:
This branch reworks the set of regulators that the Tegra PCIe driver
uses, so that the driver and DT bindings more correctly model what's
really going on in HW. For backwards-compatibility the driver will
fallback to using the old set of regulators if the new ones can't be
found.
I've made this a separate branch in case it needs to be pulled into the
PCIe tree to resolve any conflicts.
* tag 'tegra-for-3.17-pcie-regulators' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: tegra: Add new PCIe regulator properties
PCI: tegra: Overhaul regulator usage
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: tegra: move fuse code out of arch/arm" from Thierry Reding:
This branch moves code related to the Tegra fuses out of arch/arm and
into a centralized location which could be shared with ARM64. It also
adds support for reading the fuse data through sysfs.
Included is also some preparatory work that moves Tegra-related header
files from include/linux to include/soc/tegra as suggested by Arnd.
Furthermore the Tegra chip ID is now retrieved using a function rather
than a variable so that sanity checks can be done. This is convenient
in subsequent patches that will move some of the code that's currently
called from Tegra machine setup into regular initcalls so that it can
be reused on 64-bit ARM. The sanity checks help with verifying that no
code tries to obtain the Tegra chip ID before the underlying driver is
properly initialized.
* tag 'tegra-for-3.17-fuse-move' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: device tree updates for 3.17" from Shawn Guo:
The i.MX device tree updates for 3.17:
- Add device tree sources and pin function header for i.MX6SX SoC
- Initial imx6sx-sdb board support with FEC, MMC, USB, PMIC, Audio
and GPIO key enabled
- New board support: mbimxsd25 and mbimxsd27 from Eukrea, aristainetos
imx6dl boards, Rex Pro and Basic, Ka-Ro TX6
- Restructure imx6qdl-wandboard.dtsi for new rev C1 board
- Split M28EVK and M53EVK into SoM and EVK parts
- A few correction around SDMA, SSI and SATA device nodes
- Add eSATA support for Cubox-i board
- Updates on edmqmx6 to enable PCIe, I2C and CAN
- Use DT macro for clock ID for imx27 and imx6qdl
- Add FlexCAN support for VF610 SoC
* tag 'imx-dt-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (125 commits)
ARM: dts: vf610: add FlexCAN node
ARM: dts: add initial Rex Basic board support
ARM: dts: add initial Rex Pro board support
ARM: dts: mx5: Split M53EVK into SoM and EVK parts
ARM: dts: imx6: RIoTboard explicitly define pad settings
ARM: dts: vf610: fix length of eshdc1 register property
ARM: dts: Restructure imx6qdl-wandboard.dtsi for new rev C1 board.
ARM: dts: imx53: correct clock-names of SATA node
ARM: imx6: Align ssi nodes between mx6 variants
ARM: i.MX27 clk: dts: Use clock defines in DTS files
ARM: dts: imx: correct sdma compatbile for imx6sl and imx6sx
ARM: dts: imx6sx-sdb: Add audio support
ARM: dts: imx6sx: Pass the fsl,fifo-depth property
ARM: dts: imx6sx: Fix sdma node
ARM: dts: imx6: edmqmx6: Add can bus
ARM: dts: imx6: edmqmx6: Add two other i2c buses
ARM: dts: imx6: edmqmx6: Add PCIe support
ARM: dts: imx25-pdk: Add USB OTG support
ARM: dts: i.MX53: add aipstz nodes
ARM: dts: mxs: Split M28EVK into SoM and EVK parts
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: SoC changes for 3.17" from Shawn Guo:
The i.MX SoC changes for 3.17:
- Add devicetree support for i.MX1 and i.MX21 clock driver
- Use CLOCKSOURCE_OF_DECLARE() to initialize timer for DT targets
- Use of_clk_init() to initialize i.MX25 and i.MX27 clock driver in
device tree boot
- Remove i.MX1 camera support
- Remove i.MX27 IP Camera and Lite-Kit board support
- Add suspend and cpuidle support for i.mx6sx
- Clean up unused clk_register_clkdev() lookups
- Update imx-weim bus driver to support populating devices on a simple
bus
- Switch i.MX27 and i.MX6QDL clock driver to use macro for clock IDs
- Make i.MX51 a DT only platform and clean up the non-DT support code
- Support disabling supervisor protect via DT
- Random defconfig updates
* tag 'imx-soc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (69 commits)
ARM: imx: clk-vf610: fix FlexCAN clock gating
ARM: i.MX: Use CLOCKSOURCE_OF_DECLARE() for DT targets
ARM: i.MX53: globally disable supervisor protect
ARM: i.MX: allow disabling supervisor protect via DT
ARM: i.MX27 clk: Add 26 MHz oscillator circuit clock gate
ARM: i.MX27 clk: Remove unused definitions
ARM: i.MX27 clk: Introduce DT include for clock provider
ARM: i.MX: Remove Freescale Logic Product Development i.MX27 Lite-Kit board support
ARM: i.MX: Remove excess symbols ARCH_MX1, ARCH_MX25 and MACH_MX27
ARM: i.MX: Remove i.MX1 camera support
ARM: imx: use PTR_ERR_OR_ZERO
bus: imx-weim: populate devices on a simple bus
ARM: imx: build cpu_is_imx6sl function conditionally
ARM: imx: imx6sx uses imx6q cpuidle code
ARM: imx: drop PL310 errata 588369 and 727915
ARM: imx_v6_v7_defconfig: add FSL_EDMA and PRINTK_TIME
ARM: imx: clk-imx6sx: register SSI/SSI_IPG as shared gate clocks
ARM: imx_v6_v7_defconfig: Enable flexcan driver for can support
ARM: imx_v6_v7_defconfig: Enable STMPE gpio support
ARM: imx: mark .dt_compat as const
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull RCU fixes from Thomas Gleixner:
"Two RCU patches:
- Address a serious performance regression on open/close caused by
commit ac1bea8578 ("Make cond_resched() report RCU quiescent
states")
- Export RCU debug functions. Not a regression, but enablement to
address a serious recursion bug in the sl*b allocators in 3.17"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Reduce overhead of cond_resched() checks for RCU
rcu: Export debug_init_rcu_head() and and debug_init_rcu_head()
Merge "omap dts changes for v3.17 merge window, part1" from Tony Lindgren:
First set of .dts changes for omaps for v3.17 merge window:
- Enable irqchip crossbar interrupt mapping. These changes
are based on an immutable irqchip branch set up by Jason
Cooper to make it easier to merge the related .dts changes.
- Removal of omap2 related static clock data that now comes
from device tree.
- Enabling of PHY regulators for various omaps
- Enabling of PCIe for dra7
- Add support for am437x starterkit
- Enable audio for for omap5
- Enable display and am335x-evmsk
* tag 'omap-for-v3.17/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (43 commits)
ARM: DTS: omap5-uevm: Enable basic audio (McPDM <-> twl6040)
ARM: DTS: omap5-uevm: Add node for twl6040 audio codec
ARM: DTS: omap5-uevm: Enable palmas clk32kgaudio clock
ARM: dts: dra7: Add dt data for PCIe controller
ARM: dts: dra7: Add dt data for PCIe PHY
ARM: dts: dra7: Add dt data for PCIe PHY control module
ARM: dts: dra7xx-clocks: Add missing clocks for second PCIe PHY instance
ARM: dts: dra7xx-clocks: rename pcie clocks to accommodate second PHY instance
ARM: dts: dra7xx-clocks: Add missing 32KHz clocks used for PHY
ARM: dts: dra7xx-clocks: Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
ARM: dts: dra7xx-clocks: Add divider table to optfclk_pciephy_div clock
ARM: dts: dra7-evm: Add regulator information to USB2 PHYs
ARM: omap2plus_defconfig: enable TPS65218 configs
ARM: dts: AM437x: Add TPS65218 device tree nodes
ARM: dts: AM437x: Fix i2c nodes indentation
ARM: dts: AM43x: Add TPS65218 device tree nodes
ARM: dts: Add devicetree for Gumstix Pepper board
ARM: dts: dra7: add crossbar device binding
ARM: dts: dra7: add routable-irqs property for gic node
ARM: OMAP24xx: clock: remove legacy clock data
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds device tree binding documentation for the SATA
controller found on NVIDIA Tegra SoCs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add new power supply properties for input current, charge termination
current, min and max temperature
POWER_SUPPLY_PROP_TEMP_MIN - minimum operatable temperature
POWER_SUPPLY_PROP_TEMP_MAX - maximum operatable temperature
POWER_SUPPLY_PROP_INPUT_CURRENT_LIMIT - input current limit programmed
by charger. Indicates the input current for a charging source.
POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT - Charge termination current used
to detect the end of charge condition
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for the Samsung's S5PV210 SoC to the Exynos USB 2.0 PHY driver.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
[k.debski@samsung.com: cleanup and commit description]
[k.debski@samsung.com: make changes accordingly to the mailing list
comments]
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
