It's 1.6 GHz for the Cortex-A15.
Avoids warnings like "/cpus/cpu@0 missing clock-frequency property".
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the STMicroelectonics MEMS sensor devices to the Ux500
family device trees:
- Accelerometer
- Magnetometer
- Gyroscope
- Pressure (barometer)
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds some missing DMA channel information to the disabled
MMC/SD/SDIO blocks number 3 and 5, and notes that the assignment
of MSP channels vary with ASIC variant.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a VCC and VIO regulator supplies to the the STMPE expander
found on the STUIB UIB variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 has the same MMIO reset controllers matching the clocks gates,
just like in the A31. This patch adds the reset controller nodes and
the reset control phandles for the peripherals needing them to the
DTSI.
Unlike the sun6i DTSI, this patch uses sun6i-a31-clock-reset for
ahb1_rst. sun6i-a31-ahb-reset is for early init, and requires some
additions to the machine code. It is used to support the hstimer.
However the hstimer on sun8i only has 1 timer, which is somewhat
useless. Support for it will probably not be added. Hence the
decision to use sun6i-a31-clock-reset here to avoid the changes to
sun8i machine code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Merge "Renesas ARM Based SoC Cleanup for v3.17" from Simon Horman:
- Use shmobile_init_delay on r8a7790, r7s72100 and EMEV2 SoCs
- Remove unused redundant callbacks on EMEV2 SoC
* tag 'renesas-soc-cleanup-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove unused r8a7790_init_early()
ARM: shmobile: Use r8a7790 DT CPU Frequency for Lager
ARM: shmobile: Use r8a7790 DT CPU Frequency in common case
ARM: shmobile: Use shmobile_init_delay() on r7s72100
ARM: shmobile: Use shmobile_init_delay() on Genmai boards
ARM: shmobile: Update r7s72100 DTS to include CPU frequency
ARM: shmobile: Get rid of redundant EMEV2 mach callbacks
ARM: shmobile: Use shmobile_init_delay() on EMEV2
ARM: shmobile: Update EMEV2 DTS to include CPU frequency
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull "Renesas ARM Based SoC r8a7779-multiplatform Updates for v3.17" from
Simon Horman:
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
* tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: marzen: Do not use workaround for scif devices
ARM: shmobile: marzen: Initialise SCIF devices using DT
ARM: shmobile: marzen: Remove early_printk from command line
ARM: shmobile: r8a7779: Add scif nodes to dtsi
ARM: shmobile: r8a7779 dtsi: Correct #address-cells/#size-cells for clocks
ARM: shmobile: r8a7779 dtsi: Update unit-addresses for clocks
ARM: shmobile: r8a7779: Remove unused r8a7779_init_delay()
ARM: shmobile: marzen-reference: Use DT CPU Frequency
ARM: shmobile: r8a7779: Use DT CPU Frequency in common case
ARM: shmobile: r8a7779: Add Maximum CPU Frequency to DTS
ARM: shmobile: marzen-reference: Remove legacy clock support
ARM: shmobile: Remove Marzen reference DTS
ARM: shmobile: Let Marzen multiplatform boot with Marzen DTB
ARM: shmobile: Remove non-multiplatform Marzen reference support
ARM: shmobile: marzen-reference: Instantiate clkdevs for SCIF and TMU
ARM: shmobile: marzen-reference: Initialize CPG device
ARM: shmobile: r8a7779: Initial multiplatform support
ARM: shmobile: marzen-reference: Move clock and OF device initialisation into board code
ARM: shmobile: r8a7779: Move r8a7779_earlytimer_init to clock-r8a7779.c
ARM: shmobile: r8a7779: Add helper to read mode pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SPI device for RSPI on Genmai.
On this board, only rspi4 is in use. Its bus contains a single device
(a wm8978 audio codec), for which no bindings are defined yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
pwm-cells should be 3. Third cell is optional PWM flags. And This flag
supported by this binding is PWM_POLARITY_INVERTED.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have support for sun8i specific clocks in the driver,
add the corresponding clock nodes to the DTSI. Also update the
existing peripherals with the correct clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Without the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
532000000
With the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
266000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
133000000
The l3 clock derived from core DPLL is actually a divider clock,
with the default divider set to 2. l4 then derived from l3 is a fixed factor
clock, but the fixed divider is 2 and not 1. Which means the l3 clock is
half of core DPLLs h12x2 and l4 is half of l3 (as seen with this patch)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Otherwise legacy boot clock data is used. This patch also includes the
clock data files to the base dtsi files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform. Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.
For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown. Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By providing labels for rtc, wdt, cpu and dispc nodes,
boards can access them to add board-specific data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Franklin Cooper Jr. <fcooper@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ba10 tvbox is an A10 based android tvbox, with 512M RAM, 8G nand flash,
rtl8188ctv usb wifi 1 USB-A receptacle hooked up to an EHCI/OHCI controller,
1 USB-A receptacle hooked up to the OTG and 100Mbit ethernet using a
rtl8201 phy.
The PCB is labelled ba10 hence I've named the board ba10-tvbox. It is used
in noname allwinner A10 tv-boxes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LinkSprite pcDuino V3 is an A20 based development board featuring
arduino compatible io headers, 1G RAM, 4G nand, sata, rtl8188cus usb wifi
and 100 Mbit ethernet using an ip101a phy:
http://www.pcduino.com/pcduino-v3/
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
[hdegoede@redhat.com: Various cleanups, correct led pins]
[hdegoede@redhat.com: Add axp209, ir and gpio-keys nodes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sun7i block is the same as the one in the sun4i, rename the compatible
to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
I've already included the matching change to sunxi-cir.c in my pull-req to
Mauro.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At a node for the axp209, and where necessary the i2c controller to the dts
for various boards. Note the axp209 regulators are omitted as we don't have
any use for them yet, and on some boards were not sure how exactly they are
wired up.
Adding support for just the axp209 without the regulators is still useful, as
it will give us power-button and poweroff support.
Signed-off-by: Carlo Caione <carlo@caione.org>
[hdegoede@redhat.com: Drop the regulator bits for now]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At a node for the axp209, and where necessary the i2c controller to the dts
for various boards. Note the axp209 regulators are omitted as we don't have
any use for them yet, and on some boards were not sure how exactly they are
wired up.
Adding support for just the axp209 without the regulators is still useful, as
it will give us power-button and poweroff support.
Signed-off-by: Carlo Caione <carlo@caione.org>
[hdegoede@redhat.com: Drop the regulator bits for now]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl device is also an interrupt controller for external
interrupts. Add the missing #interrupt-cells property.
Also remove the unused #address-cells property.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: make the same change for sun4i, sun5i and sun6i]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets with A23 SoCs. There are at least 2 versions of the board, with
different peripherals, such as WiFi chips.
Common features among these tablets include 512 MB DRAM, NAND, MMC, LCD,
capacitive touchscreen, accelerometer, 1 or 2 camera sensors, USB OTG,
microphone and speaker.
v5 of these board designs has a ESP8089 WiFi chip (not supported)
connected to mmc1. This patch adds very basic support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A23 is a tablet oriented SoC with 2 Cortex-A7 cores
and a Mali-400MP2 GPU.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Integrator has a custom <mach/memory.h> header defining the
BUS_OFFSET for *_to_bus and bus_to_* operations as offset from
0x80000000.
This switches the Integrator over to using the mechanism
introduced for the Keystone to provide the same offset using
the device tree, deletes <mach/memory.h> and augments the
Integrator device tree to provide the bus offset.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jonathan Austin <jonathan.austin@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a stdout-path property to the Versatile devicetree so that automatic
console selection works without needing a console= line on the kernel
command line.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Merge "First AT91 fixes batch for 3.16" from Nicolas Ferre:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
Merge "mvebu fixes for v3.16" from Jason Cooper:
- mvebu
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- kirkwood
- Fix phy-connection-type on GuruPlug board
* tag 'mvebu-fixes-3.16' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
The versatile dts is missing any clock data. Add the clocks.
It is not clear from the documentation where pclk comes from, so for
now it is a dummy clock which is sufficient for things to work.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
While not needed for probing, add the "arm,pl180" compatible string for
completeness.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
