Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP
table. Due to the lack of proper OPP definition, use an arbitrary safe
value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every
OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this
value since the clock transition latency is not the only parameter that
will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since the valid Vmin voltage is not documented in the HW spec.
- clocks
phandle to the CPU clock source. This clock source is used for all the
4 CortexA15 located inside the same cluster.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Change the setting of OPPs for ES2.0]
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c3 node, to allow the generic CPUFreq driver to use it.
Enable the i2c3 pin mux and the device node as well since the
da9210 is connected to that bus.
Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Changes Vmin for disabling DVS]
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk support is not enabled in the kernel in the
shmobile defconfig it does not make much sense to provide for
it in the default command line.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (ranges_format): /clocks has empty "ranges" property but its #address-cells (2) differs from / (1)
Warning (ranges_format): /clocks has empty "ranges" property but its #size-cells (2) differs from / (1)
As r8a7779 doesn't support LPAE, change #address-cells and #size-cells from
"<2>" to "<1>", and update the affected "reg" properties to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Correct the unit-address for the "cpg_clocks" node,
- Add missing unit-addresses for the "mstp*_clks" nodes,
- Rename "cpg_clocks" and "mstp*_clks" nodes to the more generic
"clocks".
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add 1GHz to the r8a7779 DTS to describe the maximum CPU frequency.
Based on work by Magnus dam for the r8a7740 SoC.
Cc: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the DTS file r8a7779-marzen.dts can be used with
board-marzen.c and board-marzen-reference.c, proceed with removing
r8a7779-marzen-reference.dts.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let the multiplatform Marzen support boot with the legacy DTS for
Marzen as well as the Marzen reference DTS.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that r8a7779 has CCF support remove the legacy Marzen reference
Kconfig bits CONFIG_MACH_MARZEN_REFERENCE for the non-multiplatform
case.
Starting from this commit Marzen board support is always enabled via
CONFIG_MACH_MARZEN, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-marzen.c and board-marzen-reference.c
The file board-marzen-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Based on work for the Koelsch board by Laurent Pinchart.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Marzen and r8a7779 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.
Marzen board support exists in 3 flavours:
1) SHMOBILE_MULTI, MACH_MARZEN - board-marzen-reference.c (CCF + DT)
2) SHMOBILE, MACH_MARZEN_REFERENCE - board-marzen-reference.c (DT)
3) SHMOBILE, MACH_MARZEN - board-marzen.c (legacy C code)
When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Based on work for the Koelsch and r8a7791 by Magnus Damm.
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CPU Frequency information to the r7s72100 DTS file. This
will allow us to use the shared C code on r7s72100 and Genmai
which reads out the clock frequency from DT and calculates the
delay settings from there.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reference clocks using a "clocks" property in all nodes corresponding to
devices that require a clock.
Based on work by Laurent Pinchart for the r8a7790 and r8a7791 SoC.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The external crystal frequency is 31.25 on the Marzen board.
Specify it in the device tree.
Based on work for the Lager board by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Copy the device nodes from Marzen reference into the Marzen device tree
file. This will allow us to use a single DTS file regardless of kernel
configuration. In case of legacy C board code the device nodes may or
may not be used, but in the multiplatform case all the DT device nodes
will be used.
Based on a similar change for the Lager board by Laurent Pinchart.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare all core and MSTP clocks currently used by r8a7779-based boards.
Based on work by Laurent Pinchart for the r8a7790 and r8a7791 SoCs.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CPU Frequency information to the EMEV2 DTS file. This
will allow us to use the shared C code to on EMEV2 which
reads out the clock frequency from DT and calculates the
delay settings from there.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The qspi node defines crossbar number as its interrupt number. But,
the crossbar dts patches are not yet there, this causes a warning during
boot. So interrupts = < > property should be removed from DT and added
later by crossbar series.
Reported-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These new properties more accurately reflect the real connections of the
boards and therefore make it easier to match them up with schematics.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All ChromeOS ARM devices that have the standard "CrOS EC" have the
same keyboard mapping. It's silly to include this same definition
everywhere. Let's create a "dtsi" fragment that we can include from
many different boards.
This fragment is based on what's currently in tegra124-venice2.dts
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch fixes reg entry sizes in GIC node that were not
large enough to cover whole regions.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Modify the clock nodes for the ATL clocks to use the ATL clock driver to
handle them.
Add the ATL device node at the same time for DRA7.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables two IR devices in dts:
- One IR device physically found on Cubieboard 2
- One IR device physically found on Cubietruck
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: Alexsey Shestacov <wingrime@linux-sunxi.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
AM437x EPOS evm use external clock for RMII interface.
Enable the same in DT.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the Final production Data Manual for OMAP5432,
SWPS050F(APRIL 2014)
There are only two OPPs - 1GHz and 1.5GHz. the older OPP_LOW has been
completely descoped. The Nominal voltages are still correct though.
However, expectation for final production configuration is operation
with Adaptive Body Bias (ABB) and Adaptive Voltage Scaling Class 0
operation.
There are no IDcode or version change information encoded to
programmatically detect this and software is supposed to NOT use
OPP_LOW(500MHz) anymore for all devices (legacy and production
samples).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add required nodes and properties into the Berlin BG2Q device tree to
take advantage of the newly introduced SMP support. Add the scu and
cpu-ctrl nodes along with the CPUs enable-method property.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Add required nodes and properties into the Berlin BG2 device tree to
take advantage of the newly introduced SMP support. Add the scu and
cpu-ctrl nodes along with the CPUs enable-method property.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Enable the I2C0 and I2C2 for the Marvell Berlin BG2G DMP. I2C1 and I2C3
are also working on this board, but no devices seemed to be there.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Berlin BG2Q has 4 TWSI compatible with the Synopsys
DesignWare I2C driver. Add the corresponding nodes.
The pin-muxing setup is also done here, since there cannot be another
muxing setup if I2C{0,1,2,3} are enabled.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As early printk support is not enabled in the kernel in the
shmobile defconfig it does not make much sense to provide for
it in the default command line.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
N900 now seems to shut down the external oscillator when hitting
off-idle.
And Beagle XM seems to have OSC_EN pin connected to allow shutting
down the oscillator looking at the schematics. The oscillator
output is cut off in off-idle and you can monitor it from R56 on
the bottom side of the board near the power jack. Note that for
beagle we need to also enable the UART wake-up event, the others
have that enabled in earlier patches.
OMAP37XX EVM (TMDSEVM3730) does not seem to have twl4030 clken
pin connected, so there is no point trying to enable shutting
down of the oscillator on it for the extra latency it adds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Pull part two of ARM SoC updates from Arnd Bergmann:
"This is a small follow-up to the larger ARM SoC updates merged last
week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code that
came in through Russell's ARM tree. This allows the keystone platform
to do cache-coherent DMA and to finally support all the available
physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten, and
there is a small bug fix to allow building the orion5x platform again"
* tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: Drop use of meminfo since its not available anymore
ARM: orion5x: fix mvebu_mbus_dt_init call
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
ARM: keystone: Update the dma offset for non-dt platform devices
ARM: keystone: Switch over to coherent memory address space
ARM: configs: keystone: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: keystone: drop CONFIG_COMMON_CLK_DEBUG
Pull input updates from Dmitry Torokhov:
"A big update to the Atmel touchscreen driver, devm support for polled
input devices, several drivers have been converted to using managed
resources, and assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: synaptics - fix resolution for manually provided min/max
Input: atmel_mxt_ts - fix invalid return from mxt_get_bootloader_version
Input: max8997_haptic - add error handling for regulator and pwm
Input: elantech - don't set bit 1 of reg_10 when the no_hw_res quirk is set
Input: elantech - deal with clickpads reporting right button events
Input: edt-ft5x06 - fix an i2c write for M09 support
Input: omap-keypad - remove platform data support
ARM: OMAP2+: remove unused omap4-keypad file and code
Input: ab8500-ponkey - switch to using managed resources
Input: max8925_onkey - switch to using managed resources
Input: 88pm860x-ts - switch to using managed resources
Input: 88pm860x_onkey - switch to using managed resources
Input: intel-mid-touch - switch to using managed resources
Input: wacom - process outbound for newer Cintiqs
Input: wacom - set stylus_in_proximity when pen is in range
DTS: ARM: OMAP3-N900: Add tsc2005 support
Input: tsc2005 - add DT support
Input: add common DT binding for touchscreens
Input: jornada680_kbd - switch top using managed resources
Input: adp5520-keys - switch to using managed resources
...
Pull OMAP DT fbdev updates from Tomi Valkeinen:
"Here are display related device tree data changes for OMAP. They are
based on an already merged branch to satisfy the dependencies for the
dts file changes.
Add OMAP DT data:
- omap5 display subsystem
- display data for omap5 uEVM board
- am43xx display subsystem
- display data for am43xx ePOS and GP boards (LCD only)
- display data for GTA04 board
- display data for overo board
- display data for duovero-parlor board
- display data for omap3 evm and ldp boards"
* tag 'fbdev-omap-dt-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
ARM: omap5.dtsi: Add audio related parameters to hdmi node
ARM: omap4.dtsi: Add audio related parametes to hdmi node
ARM: dts: duovero-parlor: Add HDMI output
ARM: dts: overo: Add support for 3.5'' LCD output
ARM: dts: overo: Add support for 4.3'' LCD output
ARM: dts: overo: Add support for DVI output
ARM: dts: Add LCD panel sharp ls037v7dw01 support for omap3-evm and ldp
ARM: dts: omap3-gta04: Add display support
ARM: dts: omap5-uevm.dts: add display nodes
ARM: dts: omap5-uevm.dts: add tca6424a
ARM: dts: omap5.dtsi: add DSS nodes
ARM: dts: am43x-epos-evm: add LCD data
ARM: dts: am437x-gp-evm: add LCD data
ARM: dts: am4372.dtsi: add DSS information
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.16 are pretty typical: mostly clock
driver additions and fixes. There are additions to the clock core
code for some of the basic types (e.g. the common divider type has
some fixes and featured added to it).
One minor annoyance is a last-minute dependency that wasn't handled
quite right. Commit ba0fae3b06 ("clk: berlin: add core clock driver
for BG2/BG2CD") in this pull request depends on
include/dt-bindings/clock/berlin2.h, which is already in your tree via
the arm-soc pull request. Building for the berlin platform will break
when the clk tree is built on it's own, but merged into your master
branch everything should be fine"
* tag 'clk-for-linus-3.16' of git://git.linaro.org/people/mike.turquette/linux: (75 commits)
mmc: sunxi: Add driver for SD/MMC hosts found on Allwinner sunxi SoCs
clk: export __clk_round_rate for providers
clk: versatile: free icst on error return
clk: qcom: Return error pointers for unimplemented clocks
clk: qcom: Support msm8974pro global clock control hardware
clk: qcom: Properly support display clocks on msm8974
clk: qcom: Support display RCG clocks
clk: qcom: Return highest rate when round_rate() exceeds plan
clk: qcom: Fix mmcc-8974's PLL configurations
clk: qcom: Fix clk_rcg2_is_enabled() check
clk: berlin: add core clock driver for BG2Q
clk: berlin: add core clock driver for BG2/BG2CD
clk: berlin: add driver for BG2x complex divider cells
clk: berlin: add driver for BG2x simple PLLs
clk: berlin: add driver for BG2x audio/video PLL
clk: st: Terminate of match table
clk/exynos4: Fix compilation warning
ARM: shmobile: r8a7779: Add clock index macros for DT sources
clk: divider: Fix overflow in clk_divider_bestdiv
clk: u300: Terminate of match table
...
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle
Correction(DCC) to operate safely at frequencies >= 1.4GHz.
Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides
this support.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Pull ARM updates from Russell King:
- Major clean-up of the L2 cache support code. The existing mess was
becoming rather unmaintainable through all the additions that others
have done over time. This turns it into a much nicer structure, and
implements a few performance improvements as well.
- Clean up some of the CP15 control register tweaks for alignment
support, moving some code and data into alignment.c
- DMA properties for ARM, from Santosh and reviewed by DT people. This
adds DT properties to specify bus translations we can't discover
automatically, and to indicate whether devices are coherent.
- Hibernation support for ARM
- Make ftrace work with read-only text in modules
- add suspend support for PJ4B CPUs
- rework interrupt masking for undefined instruction handling, which
allows us to enable interrupts earlier in the handling of these
exceptions.
- support for big endian page tables
- fix stacktrace support to exclude stacktrace functions from the
trace, and add save_stack_trace_regs() implementation so that kprobes
can record stack traces.
- Add support for the Cortex-A17 CPU.
- Remove last vestiges of ARM710 support.
- Removal of ARM "meminfo" structure, finally converting us solely to
memblock to handle the early memory initialisation.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (142 commits)
ARM: ensure C page table setup code follows assembly code (part II)
ARM: ensure C page table setup code follows assembly code
ARM: consolidate last remaining open-coded alignment trap enable
ARM: remove global cr_no_alignment
ARM: remove CPU_CP15 conditional from alignment.c
ARM: remove unused adjust_cr() function
ARM: move "noalign" command line option to alignment.c
ARM: provide common method to clear bits in CPU control register
ARM: 8025/1: Get rid of meminfo
ARM: 8060/1: mm: allow sub-architectures to override PCI I/O memory type
ARM: 8066/1: correction for ARM patch 8031/2
ARM: 8049/1: ftrace/add save_stack_trace_regs() implementation
ARM: 8065/1: remove last use of CONFIG_CPU_ARM710
ARM: 8062/1: Modify ldrt fixup handler to re-execute the userspace instruction
ARM: 8047/1: rwsem: use asm-generic rwsem implementation
ARM: l2c: trial at enabling some Cortex-A9 optimisations
ARM: l2c: add warnings for stuff modifying aux_ctrl register values
ARM: l2c: print a warning with L2C-310 caches if the cache size is modified
ARM: l2c: remove old .set_debug method
ARM: l2c: kill L2X0_AUX_CTRL_MASK before anyone else makes use of this
...
