Add a device node for the HDA controller found on Tegra124.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add efuse and apbmisc bindings for Tegra20, Tegra30, Tegra114 and
Tegra124.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to support dynamic frequency scaling:
* the cpuclk Device Tree node needs to be updated to describe a
second set of registers describing the PMU DFS registers.
* the clock-latency property of the CPUs must be filled, otherwise
the ondemand and conservative cpufreq governors refuse to work. The
latency is high because the cost of a frequency transition is quite
high on those CPUs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404920715-19834-5-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The CA9 MPcore SoC Control block is a set of registers that allows to
configure certain internal aspects of the core blocks of the SoC
(Cortex-A9, L2 cache controller, etc.). In most cases, the default
values are fine so they aren't many reasons to touch those registers,
but there is one exception: to support cpuidle on Armada 38x, we need
to modify the value of the CA9 MPcore Reset Control register.
Therefore, this commit adds a new Device Tree binding for this
hardware block, and uses this new binding for the Armada 38x Device
Tree file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Link: https://lkml.kernel.org/r/1404913221-17343-11-git-send-email-thomas.petazzoni@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Display domain is removed due to instability issues. Explaining
the problem below:
exynos_init_late triggers the pm_genpd_poweroff_unused which powers
off the unused power domains. This call hits before the trigger to
deferred probes.
DRM DP Panel defers the probe due to supply get failure. By the time,
deferred probe is scheduled again, Display Power Domain is powered
off by pm_genpd_poweroff_unused.
FIMD and DP drivers are accessing registers during Probe and Bind
callbacks. If display domain is enabled/disabled around register
accesses, display domain gets unstable and we are getting Power Domain
Disable fail notification. Increasing the Timeout also didn't help.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add MAX98090 audio codec, I2S interface and the sound complex
nodes to enable audio on Odroid-X2/U3 boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
TFLASH (SDHCI2 controller) uses internal card detect line, but it looks
that the driver fails to operate it properly. Use GPIO interrupt on
SD_CDn line for detecting SD card state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for simple GPIO-based button availabled on
Exynos4 based Odroid boards. All supported boards have POWER button,
which has been defined in exynos4412-odroid-common.dtsi. X/X2 boards
also have additional user-configurable button which has been mapped to
KEY_HOME. All defined keys have been marked as possible wakeup source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On Odroid U2/U3 BUCK8 is used for providing power to also to P3V3
source, which is also connected to LAN9730 chip's nRESET signal. To
reset lan chip on system reboot, the BUCK8 output should not be used in
'always on' mode. This change has no impact on X/X2 boards.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves some parts of exynos4412-odroidx.dts to common
exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and
U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz
instead of 1.4GHz), while U2/U3 differs from X2 by different way of
routing signals to host USB hub. It also lacks some hw modules not yet
supported by those dts files (i.e. LCD & touch panel).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Last megabyte of RAM is used by secure firmware and should not be accessed
by Linux kernel, so correct available memory size in DTS file.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds basic support for USB modules (host and device) on
OdroidX board.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
[removed incorrect port@2 node]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for common hardware modules available on all
Exynos4412-based Odroid boards, which already have complete support in
mainline kernel. This includes secure firmware calls, watchdog, g2d and
fimc (mem2mem) multimedia accelerators.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds port sub-nodes to exynos4 ehci and ohci modules, which
are required by recently merged new exynos4 usb2 phy support.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from
being reset across sleep/wake. If we don't set it to anything then
the TPM will be reset. U-Boot will detect this as invalid
and will reset the system on resume time. This GPIO can always be low
and not hurt anything. It will get pulled back high again during a
normal warm reset when it will default back to an input.
To properly preserve the TPM state across suspend/resume and to make
the chrome U-Boot happy, properly set the GPIO to mask the
reset to the TPM.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
DRA7xx has 13 system mailboxes, and is present on both the
DRA72x and DRA74x family of SoCs. Add the DT nodes for all
these 13 mailboxes. Except for mailbox 1, all other mailboxes
do not have interrupts mapped into the MPU GIC by default.
All the mailboxes have been disabled and the interrupts
property information is left out intentionally for now,
because of the dependencies against the crossbar driver.
These mailboxes can be enabled when a usecase arises
and the crossbar driver dependencies are met.
NOTE: The mailbox 1 has different number of mailbox fifos
and IP interrupts compared to the remaining 12 mailboxes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node for AM4372 is enabled and is corrected to
remove some properties that have crept in by mistake.
Fixes: 9e3269b (ARM: dts: AM4372: Add L2, EDMA, mailbox, MMC and SHAM nodes)
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node data has been added for AM33xx device.
The mailbox IP in AM33xx is similar to the version found in
OMAP4+ devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox DT node data has been added for OMAP44xx
devices.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The number of mailbox fifos and users (IP interrupts) are added
to the Mailbox DT nodes on OMAP2420, OMAP2430, OMAP3, and OMAP5
family of SoCs through the DT properties "ti,mbox-num-fifos" and
"ti,mbox-num-users" properties. This data represents the same data
that used to be represented in hwmod attribute data through the
.num_fifos and .num_users fields previously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses twl6040 codec connected via McPDM link. McBSP1 and McBSP2 can
be used for FM/BT.
At the same time move the pinctrl handling to the correct place - under the
corresponding nodes.
Audio connectors on the board:
Headset in/out
Stereo Line out
Stereo Line in.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses twl6040 as audio codec. Move the corresponding pinctrl as
well under the node.
twl6040 needs 32k clock from palams.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Added dt data for PCIe PHY as a child node of ocp2scp3.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt.
26.3.3 PCIe Shared PHY Subsystem Integration in vE of DRA7xx ES1.0
describes the PCIe PHY subsystem-related components integrated in the device.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two instances of PCIe PHY in DRA7xx. So renamed
optfclk_pciephy_32khz, optfclk_pciephy_clk and optfclk_pciephy_div_clk to
optfclk_pciephy1_32khz, optfclk_pciephy1_clk and optfclk_pciephy1_div_clk
respectively. This is needed for adding the clocks for second PCIe PHY
instance.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
from dpll_pcie_ref_ck.
Figure 26-22. DPLL_PCIE_REF Functional Block Diagram in vE of DRA7xx ES1.0 TRM
shows the signal name for the output of post divider (M2) is CLKOUTLDO.
Figure 26-21. PCIe PHY Clock Generator Overview shows CLKOUTLDO is used as
input to apll mux.
So the actual output of dpll is dpll_pcie_ref_m2ldo_ck which is also the input
of apll.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add divider table to optfclk_pciephy_div clock. The 8th bit of
CM_CLKMODE_APLL_PCIE can be programmed to either 0x0 or 0x1
based on if the divider value is 0x2 or 0x1.
Figure 26-21. PCIe PHY Clock Generator Overview in vE of DRA7xx ES1.0 shows the
block diagram of Clock Generator Subsystem of PCIe PHY module. The divider
value if '1' should be programmed in order to get the correct
PCIE_PHY_DIV_GCLK frequency (2.5GHz).
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With sun8i PRCM support available, we can add the PRCM clock and
reset controller nodes to the DTSI. Also update R_UART's clock
phandle and add it's reset control phandle.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
add #reset-cells to socfpga.dtsi. This was missing from the
latest updates and caused the socfpga reset controller to fail
to load like so:
ffd05000.rstmgr: /soc/rstmgr@ffd05000 missing #reset-cells property
probe of ffd05000.rstmgr failed with error -22
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds necessary DT nodes for pcie controllers and miphys for SPEAr13xx
SoCs.
SPEAr1310 has 3 PCIe ports and SPEAr1340 has 1, which are multiplexed with
ahci/sata pins. By default evaluation board of both controller works in ahci
mode. Because of this, these nodes are marked "disabled" by default.
In order to use pcie controller on evaluation boards do necessary modifications
on board and enable (By replacing "disabled" with "okay") pcie and miphy from
respective 'evb' dtsi file.
Phy specific initialization was previously done from spear1340.c, which isn't
required anymore as we have separate drivers for it. Remove it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
[viresh: fixed logs/cclist/checkpatch warnings, clubbed multiple patches into one]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
SPEAr SOCs have some miscellaneous registers which are used to configure
peripheral.
This patch adds dt node and binding information for this block.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: devicetree@vger.kernel.org
[viresh: fixed logs/cclist]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.
- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The d2 Network v2 board (d2net_v2) shares a lot of hardware
characteristics with the 2Big and 5Big Network v2 boards. This patch
prepares the kirkwood-netxbig.dtsi file in order to allow to include it
from the d2net_v2 DTS file. The DT nodes only relevant for the 2Big and
5Big Network v2 boards are moved into their respective DTS files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-2-git-send-email-simon.guinot@sequanux.org
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Merge "Third Round of Renesas ARM Based SoC r8a7779-multiplatform Updates
for v3.17" from Simon Horman:
- Consistently use tabs for indentation
* tag 'renesas-r8a7779-multiplatform3-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen: Consistently use tabs for indentation
Signed-off-by: Olof Johansson <olof@lixom.net>
