The ldousb_reg regulator provides power to the USB1 and USB2
High Speed PHYs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a IRQ crossbar device in the soc, which
maps the irq requests from the peripherals to the
mpu interrupt controller's inputs. The Peripheral irq
requests are connected to only one crossbar
input and the output of the crossbar is connected to only one
controller's input line. The crossbar device is used to map
a peripheral input to a free mpu's interrupt controller line.
Here, adding a new crossbar device node and replacing all the peripheral
interrupt numbers with its fixed crossbar input lines.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a IRQ crossbar device in the soc, which maps the
irq requests from the peripherals to the mpu interrupt
controller's inputs. The gic provides the support for such
IPs in the form of routable-irqs. So adding the property
here to gic node.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add ABB device nodes for OMAP5 family of devices. Data is based on
final production OMAP543x Technical Reference Manual revision Z (April 2013).
Final production Data Manual for OMAP5432 SWPS050F(APRIL 2014).
[nm@ti.com: co-developer and updates to latest documentation]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "Berlin DT changes for v3.17" from Sebastian Hesselbarth:
- L2CC latency properties for BG2Q
- DW i2c nodes for BG2Q and corresponding dev board
- SMP related nodes for BG2 and BG2Q
* tag 'berlin-dt-3.17-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add SMP related nodes and properties for BG2Q
ARM: dts: berlin: add SMP related nodes and properties for BG2
Documentation: bindings: add the marvell,berlin-smp CPU enable method
Documentation: bindings: add the Berlin CPU control doc
ARM: dts: berlin: enable i2c0 and i2c2
ARM: dts: berlin: add I2C nodes for BG2Q
ARM: dts: berlin2q: set L2CC tag and data latency to 2 cycles
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "First pull request of Versatile family clean-ups for v3.17" from Linus
Walleij:
- Remove <mach/memory.h> from the Integrator, paving the
road for multiplatform.
- Push the CLCD helper code down into the framebuffer subsystem,
removing the last hook in plat-versatile for the Integrator,
also paving the road for multiplatform.
Patches tested on Integrator/AP, Integrator/CP and Versatile AB
(all real hardware).
* tag 'versatile-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
video: move Versatile CLCD helpers
ARM: integrator: get rid of <mach/memory.h>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "DT IRQ and clock support for Versatile platforms" from Rob Herring.
This branch moves IRQ and clock support over to DT for the versatile
platforms.
* tag 'versatile-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
clk: versatile: add versatile OSC support
dts: versatile: add clock tree
ARM: timer-sp: allow getting timer1 clock from DT to fallback to legacy clock
dt/bindings: add compatible string for versatile osc clock
dt/bindings: arm-boards: add binding for Versatile core module
dts: versatile: add pl180 compatible strings
ARM: versatile: remove init_irq hook for DT boot
ARM: integrator: convert to use irqchip_init
irqchip: versatile-fpga: add support for arm,versatile-sic
irqchip: versatile-fpga: Add IRQCHIP_DECLARE support
dts: versatile: add missing irq controller properties
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Samsung fixes-2 for v3.16" from Kukjin Kim:
- fix the check for SMP configuration with using CONFIG_SMP
not just SMP
- fix the number of pwm-cells for exynos4 pwm
- fix ftrace for exynos_mct
- register exynos_mct for stable udely
- fix secondary boot addr for secure mode for exynos SoCs
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Update secondary boot addr for secure mode
clocksource: exynos_mct: Register the timer for stable udelay
clocksource: exynos_mct: Fix ftrace
ARM: dts: fix pwm-cells in pwm node for exynos4
ARM: EXYNOS: Fix the check for non-smp configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently CLK_FOUT_EPLL was set as one of the parents of AUDSS mux.
As per the user manual, it should be CLK_MAU_EPLL.
The problem surfaced when the bootloader in Peach-pit board set
the EPLL clock as the parent of AUDSS mux. While booting the kernel,
we used to get a system hang during late boot if CLK_MAU_EPLL was
disabled.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
It's 1.6 GHz for the Cortex-A15.
Avoids warnings like "/cpus/cpu@0 missing clock-frequency property".
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
As this board use external clock for RMII interface we should specify 'rmii'
phy mode and 'rmii-clock-ext' to make ethernet working.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of FIFO in McASP can reduce the risk of audio under/overrun and
lowers the load on the memories since the DMA will operate in bursts.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After clarification from the hardware team it was found that
this 1.8V PHY supply can't be switched OFF when SoC is Active.
Since the PHY IPs don't contain isolation logic built in the design to
allow the power rail to be switched off, there is a very high risk
of IP reliability and additional leakage paths which can result in
additional power consumption.
The only scenario where this rail can be switched off is part of Power on
reset sequencing, but it needs to be kept always-on during operation.
This patch is required for proper functionality of USB, SATA
and PCIe on DRA7-evm.
CC: Rajendra Nayak <rnayak@ti.com>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the STMicroelectonics MEMS sensor devices to the Ux500
family device trees:
- Accelerometer
- Magnetometer
- Gyroscope
- Pressure (barometer)
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds some missing DMA channel information to the disabled
MMC/SD/SDIO blocks number 3 and 5, and notes that the assignment
of MSP channels vary with ASIC variant.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a VCC and VIO regulator supplies to the the STMPE expander
found on the STUIB UIB variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The A23 has the same MMIO reset controllers matching the clocks gates,
just like in the A31. This patch adds the reset controller nodes and
the reset control phandles for the peripherals needing them to the
DTSI.
Unlike the sun6i DTSI, this patch uses sun6i-a31-clock-reset for
ahb1_rst. sun6i-a31-ahb-reset is for early init, and requires some
additions to the machine code. It is used to support the hstimer.
However the hstimer on sun8i only has 1 timer, which is somewhat
useless. Support for it will probably not be added. Hence the
decision to use sun6i-a31-clock-reset here to avoid the changes to
sun8i machine code.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Merge "Renesas ARM Based SoC Cleanup for v3.17" from Simon Horman:
- Use shmobile_init_delay on r8a7790, r7s72100 and EMEV2 SoCs
- Remove unused redundant callbacks on EMEV2 SoC
* tag 'renesas-soc-cleanup-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove unused r8a7790_init_early()
ARM: shmobile: Use r8a7790 DT CPU Frequency for Lager
ARM: shmobile: Use r8a7790 DT CPU Frequency in common case
ARM: shmobile: Use shmobile_init_delay() on r7s72100
ARM: shmobile: Use shmobile_init_delay() on Genmai boards
ARM: shmobile: Update r7s72100 DTS to include CPU frequency
ARM: shmobile: Get rid of redundant EMEV2 mach callbacks
ARM: shmobile: Use shmobile_init_delay() on EMEV2
ARM: shmobile: Update EMEV2 DTS to include CPU frequency
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull "Renesas ARM Based SoC r8a7779-multiplatform Updates for v3.17" from
Simon Horman:
Move r8a7779 SoC and its Marzen board to use common clocks,
multiplatform and initialise SCIF (serial) devices using DT.
* tag 'renesas-r8a7779-multiplatform-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: marzen: Do not use workaround for scif devices
ARM: shmobile: marzen: Initialise SCIF devices using DT
ARM: shmobile: marzen: Remove early_printk from command line
ARM: shmobile: r8a7779: Add scif nodes to dtsi
ARM: shmobile: r8a7779 dtsi: Correct #address-cells/#size-cells for clocks
ARM: shmobile: r8a7779 dtsi: Update unit-addresses for clocks
ARM: shmobile: r8a7779: Remove unused r8a7779_init_delay()
ARM: shmobile: marzen-reference: Use DT CPU Frequency
ARM: shmobile: r8a7779: Use DT CPU Frequency in common case
ARM: shmobile: r8a7779: Add Maximum CPU Frequency to DTS
ARM: shmobile: marzen-reference: Remove legacy clock support
ARM: shmobile: Remove Marzen reference DTS
ARM: shmobile: Let Marzen multiplatform boot with Marzen DTB
ARM: shmobile: Remove non-multiplatform Marzen reference support
ARM: shmobile: marzen-reference: Instantiate clkdevs for SCIF and TMU
ARM: shmobile: marzen-reference: Initialize CPG device
ARM: shmobile: r8a7779: Initial multiplatform support
ARM: shmobile: marzen-reference: Move clock and OF device initialisation into board code
ARM: shmobile: r8a7779: Move r8a7779_earlytimer_init to clock-r8a7779.c
ARM: shmobile: r8a7779: Add helper to read mode pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add SPI device for RSPI on Genmai.
On this board, only rspi4 is in use. Its bus contains a single device
(a wm8978 audio codec), for which no bindings are defined yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge OMAP fixes from Tony Lindgren:
Fixes for omaps for issues discovered during the merge window and
enabling of a few features that had to wait for the driver
dependencies to clear.
The fixes included are:
- Fix am43xx hard reset flags
- Fix SoC detection for DRA722
- Fix CPU OPP table for omap5
- Fix legacy mux parser bug if requested muxname is a prefix of
multiple mux entries
- Fix qspi interrupt binding that relies on the irq crossbar
that has not yet been enabled
- Add missing phy_sel for am43x-epos-evm
- Drop unused gic_init_irq() that is no longer needed
And the enabling of features that had driver dependencies are:
- Change dra7 to use Audio Tracking Logic clock instead of a fixed
clock now that the clock driver for it has been merged
- Enable off idle configuration for selected omaps as all the kernel
dependencies for device tree based booting are finally merged as
this is needed to get the automated PM tests working finally with
device tree based booting
- Add hwmod entry for ocp2scp3 for omap5 to get sata working as
all the driver dependencies are now in the kernel and this patch
fell through the cracks during the merge window
* tag 'omap-for-v3.16/fixes-against-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7-evm: remove interrupt binding
ARM: OMAP2+: Fix parser-bug in platform muxing code
ARM: DTS: dra7/dra7xx-clocks: ATL related changes
ARM: OMAP2+: drop unused function
ARM: dts: am43x-epos-evm: Add Missing cpsw-phy-sel for am43x-epos-evm
ARM: dts: omap5: Update CPU OPP table as per final production Manual
ARM: DRA722: add detection of SoC information
ARM: dts: Enable twl4030 off-idle configuration for selected omaps
ARM: OMAP5: hwmod: Add ocp2scp3 and sata hwmods
ARM: OMAP2+: hwmod: Change hardreset soc_ops for AM43XX
pwm-cells should be 3. Third cell is optional PWM flags. And This flag
supported by this binding is PWM_POLARITY_INVERTED.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have support for sun8i specific clocks in the driver,
add the corresponding clock nodes to the DTSI. Also update the
existing peripherals with the correct clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Without the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
532000000
With the patch:
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck # cat clk_rate
532000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div # cat clk_rate
266000000
/debug/.../dpll_core_x2_ck/dpll_core_h12x2_ck/l3_iclk_div/l4_root_clk_div # cat clk_rate
133000000
The l3 clock derived from core DPLL is actually a divider clock,
with the default divider set to 2. l4 then derived from l3 is a fixed factor
clock, but the fixed divider is 2 and not 1. Which means the l3 clock is
half of core DPLLs h12x2 and l4 is half of l3 (as seen with this patch)
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Otherwise legacy boot clock data is used. This patch also includes the
clock data files to the base dtsi files.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
