Many of the boards use GPIO-mapped buttons for generic input.
For Arndale board, these buttons also serve as wakeup source.
And the issues reported in commit 522ccdb6fd ("ARM: dts:
Disable the RTC by default on exynos5") are no longer reproduced
on EXYNOS5250 based systems. Hence it would be better to re-enable
RTC support for EXYNOS5250.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
[mturquette@linaro.org: ack on RTC enabling]
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
On OMAP2+ platforms, USB support needs physical layer signalling and
the NOP USB Transceiver driver since v3.10. This patch enables USB_PHY
and NOP_USB_XCEIV in omap2plus_defconfig. These two are harmless to
the kernel stability, and useful since they are required for USB and
Ethernet (over USB) support.
We do not enable USB_EHCI_HCD here because all features aren't fully
supported yet.
This patch applies to Linux 3.10-rc3.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Adrien Vergé <adrienverge@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
From Santosh Shilimkar:
SOC support for Keystone II devices:
- Minimal machine and device-tree support with arch_timers and console UART
- Reboot hook using PLL reset
- Low level debug support using UART
- SMP boot support
* tag 'keystone-soc-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: Enable SMP support on Keystone machines
ARM: keystone: Add minimal TI Keystone platform support
ARM: dts: keystone: Add minimal Keystone SOC device tree data
Signed-off-by: Olof Johansson <olof@lixom.net>
Texas Instruments Keystone family of multi-core devices are
based on ARM Cortex A15. Patch adds basic definitions for a
new Keystone sub-architecture in ARM.
The TCI66xxK2H Communications Infrastructure Keystone SoCs
are member of the C66x family based on TI's new KeyStone 2
multi-core SoC Architecture designed specifically for high
performance wireless and networking infrastructure applications.
The SOCs contains many subsystems like Cortex A15 ARM CorePacs,
C66XX DSP CorePacs, MSMC memory controller, Tera Net bus,
IP Network, Navigator, Hyperlink, 1G/10G Ethernet, Radio layers
and queue based communication systems.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Enable MMC_UNSAFE_RESUME to be accomplish a proper suspend/resume cycle
for SD/SDIO/(e)MMC.
ARMMMCI host driver supports clock gating through runtime PM, thus
MMC_CLKGATE is not needed. Moreover ARMMMCI can do scatter-gather which
means we can explicity disable MMC_BLOCK_BOUNCE, since it's default
enabled, to skip unnecessary bounce buffer copying.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we removed our dependency on <mach/*> the U300
can be converted to mutliplatform. Remove the invalid restriction
that U300 would not support AUTO_ZRELADDR (it does) and update
the defconfig in the process.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove board support for the r8a7740 based Bonito board
The r8a7740 SoC support code is still kept around since it
is in use by the Armadillo800eva board which is basically a more
recent board where the design is based on Bonito.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove board support for the sh7372 based AP4EVB board
The sh7372 SoC support code is still kept around since it
is in use by the Mackerel board which is basically a more
recent board where the design is based on AP4EVB.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
From Nicolas Ferre:
Adding the DT support to USB gadget High-Speed aka usba.
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
USB: gadget: atmel_usba: add DT support
USB: gadget: atmel_usba: allow multi instance
USB: gadget: atmel_usba: move global struct usba_ep usba_ep to struct usba_udc
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
ARM: at91: dt: use #include for all device trees
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/at91sam9260.dtsi
arch/arm/boot/dts/sama5d3.dtsi
From Stephen Warren:
ARM: tegra: defconfig updates
Enable some new features:
* The Tegra114 SPI controller, for Dalmore's SPI flash.
* Set all the GPIO leds triggers to their "if you don't know, say X"
value, so there are some useful triggers for the gpio-leds support.
* TPS65090 charger, for Dalmore.
* ASoC RT5640 machine driver, for audio on Beaver and Dalmore.
Also, rebuild tegra_defconfig on top of linux-next. This should make it
easier to create future defconfig patches, without extraneous diffs.
* tag 'tegra-for-3.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: defconfig updates
Signed-off-by: Olof Johansson <olof@lixom.net>
From Simon Horman:
Second Round of Renesas ARM based SoC defconfig updates for v3.11
* Changes by Morimoto-san to enable MMCIF, M25P80 and RTC RX8581 for the
bockw board
* tag 'renesas-defconfig2-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: bockw defconfig: add MMCIF support
ARM: shmobile: bockw defconfig: add M25P80 support
ARM: shmobile: bockw defconfig: add RTC RX8581 support
Signed-off-by: Olof Johansson <olof@lixom.net>
From Stephen Warren:
ARM: bcm2835: defconfig updates
This enables gpio-leds and simplefb.
* tag 'bcm2835-for-3.11-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: defconfig updates
mvebu register map changes for v3.11
This series removes the hardcoded register base address for mvebu.
Depends:
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
* tag 'regmap-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: disable DEBUG_LL/EARLY_PRINTK in defconfig
arm: mvebu: add another earlyprintk Kconfig option
arm: mvebu: don't hardcode the physical address for mvebu-mbus
arm: mvebu: don't hardcode a physical address in headsmp.S
arm: mvebu: remove hardcoded static I/O mapping
arm: mvebu: move cache and mvebu-mbus initialization later
arm: mvebu: avoid hardcoded virtual address in coherency code
arm: mvebu: remove dependency of SMP init on static I/O mapping
arm: mvebu: fix length of Ethernet registers area in .dtsi
arm: mvebu: fix length of SATA registers area in .dtsi
arm: mvebu: mark functions of armada-370-xp.c as static
ARM: mvebu: Remove init_irq declaration in machine description
ARM: Orion: Remove redundant init_dma_coherent_pool_size()
Signed-off-by: Olof Johansson <olof@lixom.net>
Pulling in a set of fixes from Tony Lindgren to resolve conflicts with later
cleanup branch:
A set of small fixes for omaps for the -rc cycle:
- am7303 iva2 reset PM regression fix
- am33xx uart2 dma channel fix
- am33xx gpmc properties fix
- omap44xx rtc wake-up mux fix for nirq pins
- omap36xx clock divider restore fix
There's also one tiny non-critical .dts fix for omap5
timer pwm properties.
* tag 'omap-for-v3.10/fixes-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that we have two different addresses for the UART, depending on
which bootloader is used, it is no longer desirable to enable
earlyprintk by default in the defconfig. Users who need earlyprintk
support will have to enable it explicitly, and select the right UART
configuration depending on their platform.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Enable some new features:
* The Tegra114 SPI controller, for Dalmore's SPI flash.
* Set all the GPIO leds triggers to their "if you don't know, say X"
value, so there are some useful triggers for the gpio-leds support.
* TPS65090 charger, for Dalmore.
* ASoC RT5640 machine driver, for audio on Beaver and Dalmore.
Also, rebuild tegra_defconfig on top of linux-next. This should make it
easier to create future defconfig patches, without extraneous diffs.
This should introduce no changes; simply moving entries around due to
Kconfig ordering changes. The apparent exceptions are:
* AUTO_ZRELADDR: Selected by ARM multi-platform support.
* MTD_CHAR: Removed in Kconfig.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren, squashed various patches]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
The mailbox hardware (in OMAP) uses a queued mailbox interrupt
mechanism that provides a communication channel between processors
through a set of registers and their associated interrupt signals
by sending and receiving messages.
The OMAP mailbox framework/driver code is moved to be under
drivers/mailbox, in preparation for adapting to a common mailbox
driver framework. This allows the build for OMAP mailbox to be
enabled (it was disabled during the multi-platform support).
As part of the migration from plat and mach code:
- Kconfig symbols have been renamed to build OMAP1 or OMAP2+ drivers.
- mailbox.h under plat-omap/plat/include has been split into a public
and private header files. The public header has only the API related
functions and types.
- The module name mailbox.ko from plat-omap is changed to
omap-mailbox.ko
- The module name mailbox_mach.ko from mach-omapX is changed as
mailbox_omap1.ko for OMAP1
mailbox_omap2.ko for OMAP2+
Cc: Tony Lindgren <tony@atomide.com>
[gregkh@linuxfoundation.org: ack for staging part]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
From Simon Horman:
Renesas ARM based SoC defconfig updates for v3.11
kzm9g: Enable AS3711 PMIC
bockw: Enable, USB, PM_RUNTIME, I2C and SDHI
armadillo800eva: Correct SERIAL_SH_SCI_NR_UARTS
* tag 'renesas-defconfig-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g: enable AS3711 PMIC in defconfig
ARM: shmobile: bockw: enable USB in defconfig
ARM: shmobile: bockw: enable CONFIG_PM_RUNTIME in defconfig
ARM: shmobile: bockw: enable I2C in defconfig
ARM: shmobile: bockw: enable SDHI on defconfig
ARM: shmobile: armadillo800eva: Fix maximum number of SCIF
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Atheros 803X phy driver support in defconfig which is present in
AM335x EVM and EVM Starter Kit.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An AS3711 PMIC is used on kzm9g to supply CPU power and LCD backlight.
This patch enables it in board defconfig.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable USB platform EHCI/OHCI and common PHY drivers in 'bockw_defconfig'.
Enable USB storage driver and SCSI disk driver that it needs as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In order to utilise all of the memory located on ux500 based devices
we have to enable HIGHMEM. Without it the kernel truncates memory down
to what's left after the PAGE_OFFSET has been applied, which doesn't
leave an awful lot, especially if we're running large rootfs' such
as full Linux desktop distributions or Android.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper, mvebu defconfig changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'defconfig-3.11-3' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: Enable cpufreq and ondemand on kirkwood_defconfig
arm: kirkwood: update defconfig with PCIe driver and board updates
arm: mvebu: update defconfig with PCI and USB support
ARM: Kirkwood: Enable USB 3.0 in kirkwood_defconfig
ARM: kirkwood: enable Sheevaplug DT in defconfig
ARM: mvebu: Add support for USB storage class in mvebu_defconfig
the low power version have a mmc-spi
eanble mmc-spi and RV3029C2 RTC in at91_dt_defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable CONFIG_LEDS_GPIO and all options required to enable it, or make
the option useful.
Enable the simple framebuffer driver, fbconsole, and VT support.
This patch also regenerated bcm2835_defconfig, which removes two HW_RANDOM
entries, since they're enabled by default.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Pull ARM Exynos fixes from Olof Johansson:
"Here's a shorter set of fixes for 3.10, all for Samsung Exynos
platforms.
It also includes a defconfig update so that exynos_defconfig provides
a meaningful set of drivers to boot an unmodified kernel on the
Samsung ARM-based Chromebooks."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: exynos: defconfig update
ARM: SAMSUNG: Add names to fimd0 IRQ resources
ARM: EXYNOS: fix software reset logic for EXYNOS5440 SOC
ARM: EXYNOS: Fix support of Exynos4210 rev0 SoC
ARM: dts: Enabling samsung-usb2phy driver for exynos5250
This turns on a number of configs that are useful on the Chromebook, but also
good to have on in general:
* USB host and MMC drivers(!)
* I2C GPIO arbitration driver
* CYAPA trackpad driver
* simplefb
* CROS EC and keyboard drivers
* S5M8767 driver
* MAX77686 drivers
* MAX8997 driver
* DEVTMPFS + mount
* DM_CRYPT (as module)
* CRYPTOLOOP
* HIGHMEM
* PRINTK timestamps
This also turns off DEBUG_LL, and switches the hardcoded Samsung lowlevel
uart to uart 3 (which is only used to show the "uncompressing kernel"
message at boot, it seems).
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
From Nicolas Ferre:
Big update converting pinctrl to use macros and header files. Increases
readability and avoids typos.
Update of AT91 defconfigs and merge of defconfigs for the similar SoCs
sam9260/9g20 and sam9261/9g10.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
ARM: at91: dt: use #include for all device trees
Signed-off-by: Olof Johansson <olof@lixom.net>
From Linus Walleij:
Device tree patches for the Nomadik machine:
- Move clock registration to the device tree
- Support probing the MTU timer from the device tree
- Register user LED and user key in the device tree
- Update defconfig to account for user LED and user key
- Move pin control mappings to the device tree
* tag 'nomadik-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: move the pin configuration to DT
ARM: nomadik: add led and key for S8815
ARM: nomadik: register clocksource from device tree
ARM: nomadik: convert all clocks except timer to dt
clocksource: nomadik-mtu: support of probe
Signed-off-by: Olof Johansson <olof@lixom.net>
