Without that change wifi card isn't probed because pwrseq is necessary for
libertas chip.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define pinmux and usage if irq pin + fix irq edge.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define pwm backlight node which is using dmtimer pwm.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Secure variants of DRA7xx and AM57xx SoCs may need to reserve a region
of the SRAM for use by secure software. To account for this, add a child
node to the ocmcram1 node that will act as a placeholder at the start
of the SRAM for the reserved region of memory that may be required
by secure services. The node is added with size 0 so that by default
parts will have the full space available but the bootloader or board dts
file is able to resize the node as needed depending on how much reserved
space is needed, if any, so end users of the ocmcram1 region on HS parts
must be aware that a smaller amount of SRAM than expected may be available.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add all ocmcram nodes to dra7.dtsi using the generic mmio-sram driver.
DRA7xx and AM57xx families of SoCs can contain three ocmcram regions of
SRAM, one of 512kb and also an optional two additional of 1Mb each. Mark
the two additional 1MB regions of SRAM as disabled as only ocmcmram1 is
on all variants of the SoCs, then depending on which specific variant
is in use the ocmcram2 and ocmcram3 nodes can be enabled in the board
dts file if the data manual for that part number indicates the ocmcram
region is available.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add PWMSS device tree nodes for DRA7 SoC family and add documentation
for dt bindings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Add eCAP and use updated bindings for PWMSS and ePWM]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previous patches switched the ECAP and EPWM to use the new bindings.
These bindings explicitly adds the various required clocks via DT rather
than depending on hwmod.
Therefore, it is safe to remove the hwmod entries since they are no longer
needed.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch to a new ECAP and EPWM bindings that doesn't depend on hwmod to
provide the various required clocks.
For AM437 and AM335x, add the required clocks explicitly to DT. The
hwmod entries for ECAP and EPWM will be removed and this will prevent
anything from breaking.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid depending on the bootloader or the ROM for configuring the pinmux by
explicitly setting the pinmux here.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The pinctrl IP used in some of the Keystone 2 devices differ vs other
TI SoCs. Therefore, create a Keystone specific pinctrl header.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Enable FPGA's IRQ controller. It is in charge of dispatching interrupts
generated by IPs in the FPGA. The SoC is notified that an interrupt
occurred through a GPIO.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 6c42db30d8 introduced audio support based on alsa ucm profiles
taken from the ChromeOS userspace. Both in the kernel as well as alsa
they were named (and matched against) ROCKCHIP-I2S. Audio profiles are
very much board-specific and hogging the ROCKCHIP-I2S name would make
it harder for future boards and also is misleading.
For Veyron boards the audio setup is similar over all variants, so
VEYRON-I2S is a more suitable name. This rename also was merged into
the alsa ucm profile so both userspace and kernel match and the old
naming was never released in any alsa or kernel release.
Fixes: 6c42db30d8 ("ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
DSS's 'pll2_clkctrl' and 'pll2' have wrong addresses in the dra74x.dtsi
file. Video PLL2 has not been used so wrong addresses went unnoticed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pinctrl node and populate the pinctrl registers with the default
values.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The PCI DT bindings contain a bogus entry for IO space which is not
supported on Keystone. The current bogus entry has an invalid size
and throws following error during boot.
[0.420713] keystone-pcie 21021000.pcie: error -22: failed to map
resource [io 0x0000-0x400000003fff]
So remove it from the dts. While at it also add a bus-range
value that eliminates following log at boot up.
[0.420659] No bus range found for /soc/pcie@21020000, using [bus 00-ff]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The notion of which uart instance is serial0 or serial1
is board specific rather than generic to the chip. This
patch removes the serial aliases from generic chip dtsi
and adds an appropriate alias to the board specific dtsi.
By making the alias for serial0 point to uart1 for the arria10_socdk,
the linux boot command line supports specifying console=ttyS0,115200
for backwards compatibility, and it supports not specifying
the console at all.
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Without having an ethernet alias, ethernet will have a random MAC address,
versus take an address that was provided from the bootloader.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
MFC device can be used without any external hardware dependencies (when
IOMMU is enabled), so it can be enabled by default (like it has been
already done for Exynos 542x platforms). This unifies handling of this
device for Exynos3250, Exynos4 and Exynos542x platforms. Board can still
include exynos-mfc-reserved-memory.dtsi to enable using this device
without IOMMU being enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Generic reserved memory regions bindings allow to automatically allocate
region of given parameters (alignment and size), so use this feature
instead of the hardcoded values, which had no dependency on the real
hardware. This patch also increases "left" region from 8MiB to 16MiB to
make the codec really usable with nowadays steams (with 8MiB reserved
region it was not even possible to decode 480p H264 video).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Using the new line naming mechanism from the GPIO subsystem, name
the GPIO lines on the HREFv60plus board that are connected as
GPIO on this design.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the new line naming mechanism from the GPIO subsystem, name
the GPIO lines on the Snowball board that are connected as
GPIO on this design.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the compatible string "stericsson,ab8500" from the board
definitions into the main node in the chipset file where it
belongs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use compatible "atmel,sama5d2-ohci" to be capable of suspending
ports while sleep to save the power consumption.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bea7eef694 ("ARM: dts: exynos: Fix DTC unit name warnings in
Peach Pit") fixed the DTC warnings about mismatches between unit names
and reg properties in the Exynos5420 Peach Pit DTS.
But unfortunately it also added a regression on the Peach Pit when
changing the port node names since the OF graph logic expects the port
nodes to be always named 'port'.
The Documentation/devicetree/bindings/graph.txt binding document says
that when there is more than one port, '#address-cells', '#size-cells'
and 'reg' properties should be used to number the port nodes.
Fixes: bea7eef694 ("ARM: dts: exynos: Fix DTC unit name warnings in Peach Pit")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Commit 5c9cbade06 ("ARM: dts: exynos: Fix DTC unit name warnings in
Exynos5250") fixed all the DTC warnings about mismatchs between unit
names and reg properties in Exynos5250 boards DTS.
But unfortunately it also added a regression on the Exynos5250 Snow
Chromebook when changing the port node names since the OF graph logic
expects the port nodes to be always named 'port'.
The Documentation/devicetree/bindings/graph.txt binding document says
that when there is more than one port, '#address-cells', '#size-cells'
and 'reg' properties should be used to number the port nodes.
Fixes: 5c9cbade06 ("ARM: dts: exynos: Fix DTC unit name warnings in Exynos5250")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add device tree files for the Broadcom BCM23550 SoC and the
Broadcom Sparrow board.
Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The thermal nodes are not disabled in exynos5420.dtsi so there is no
need to manually enable them on Odroid XU3/XU3-Lite/XU4 boards.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Move watchdog and Security SubSystem nodes from exynos5420.dtsi to file
shared with Exynos5410 and configure the clocks on the latter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Extend the DTS for Exynos5410-based Odroid XU board with:
1. Proper PWM outputs,
2. usb3503 USB HUB (with integrated LAN9730 ethernet adapter (smsc95xx)),
3. Maxim 77802 PMIC (regulators, 32 kHz clocks, RTC),
4. CPU thermal (trip points are the same as in Odroid XU3/XU4 but
cooling maps are different as there is no CPU freq and only one
cluster available for now),
5. Regulator supplies for USB 3.0.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Add nodes for Thermal Management Unit to exynos5410.dtsi. Use the same
compatible as for Exynos5420 however without second base for TRIMINFO
register and without TMU for GPU.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Add input mux for UART2 RX in DTE mode. This allows to use the pad
UART2_TX_DATA_ALT0 as UART2 RX. This particular input select seems
to be missing in current reference manuals (Rev. B), but when looking
at the tables and other UART input select registers (e.g. UART3) it
seems naturally that this input mux register also has a fourth pad
option for UART2_TX_DATA_ALT0. It has also been proven to be required
to use UART2 in DTE mode and the particular pads on the Colibri iMX7
platform.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass "fsl,sai-mclk-direction-output" to the sai2 node, so that the
SAI2_MCLK can be an output.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SAI alias entries, which makes it possibe for the SAI driver
to retrieve the port instance.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Building with W=1 option leads to several warnings like:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch replaces custom properties for defining reserved memory
regions with generic reserved memory bindings for MFC video codec
device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Add Samsung copyrights]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
On Exynos5410 the SPI interrupt for second USB DWC3 (called DRD: Dual
Role Device) is different - 200 instead of 73.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Hang the three switches of the three MDIO busses using the new DSA
binding. Also, make use of the mdio-bus and explicitly list the phys
on one device. This is not required, but good for testing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
